LAISHA
Open Laisha

EHEDG hygienic design training

International (Europe-based) · European Hygienic Engineering & Design Group · unverified source

37practice questions written to this syllabus
4subjects

What EHEDG hygienic design training is

EHEDG hygienic design training is a professional certification run by European Hygienic Engineering & Design Group, for candidates worldwide.

Format

Hygienic design courses and certificates for engineers and food technologists.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose.

Check the current format, eligibility, fees and dates on the official site: ehedg.org.

How it has changed

The guidelines themselves are cited in the food-plant-design-utilities subject.

How to prepare for EHEDG hygienic design training

Where our 37 questions for it fall

Our reading of the syllabus, from the questions we have written to this exam; the exam body's own weighting, where published, is under Format above.

  1. Heaviest (86% of the questions): Food Plant Design, Hygienic Engineering, Utilities & Automation (20); Food Plant Sanitation, Cleaning & Pest Management (12).

    Start here: read these subjects' manuals first and work their questions until the reasoning is automatic.

  2. Middle band: Transport Phenomena in Food Processing: Fluid Flow, Heat & Mass Transfer (3); Mechanical Unit Operations: Size Reduction, Mixing & Separation (2).

    One pass per subject, then mixed sets across them.

  3. Hardest share: Food Plant Sanitation, Cleaning & Pest Management (3 hard of 12), Food Plant Design, Hygienic Engineering, Utilities & Automation (2 hard of 20).

    Leave untimed time for these and read every explanation, including for the options you rejected.

Official source: ehedg.org

8 practice questions, worked

Original questions written to this exam's published syllabus and pattern. Not past papers.

1. In an HTST pasteuriser, the timing pump is usually a positive-displacement pump because

  1. its flow rises when downstream pressure rises, keeping milk hotter
  2. it needs no electrical power when milk is flowing
  3. it can be run against a closed valve indefinitely
  4. its flow is set by speed, which fixes the minimum holding time
Answer and working

D. its flow is set by speed, which fixes the minimum holding time

PD flow is nearly independent of discharge pressure, so the maximum flow, and hence the minimum holding time, is controlled. PD pumps must not run against a closed valve without relief.

Transport Phenomena in Food Processing: Fluid Flow, Heat & Mass Transfer · Pumps for foods: centrifugal and positive-displacement

2. Why should dead legs be avoided in hygienic pipework?

  1. They raise the flow velocity too high for cleaning
  2. Cleaning solution does not flow through them, so soil and microbes remain
  3. They let sanitiser drain away too quickly
  4. They make the conductivity sensor read too low
Answer and working

B. Cleaning solution does not flow through them, so soil and microbes remain

In a dead leg the liquid is stagnant during CIP, so soil and biofilms persist and recontaminate product. Hygienic-design guidance keeps any unavoidable branch very short.

Food Plant Sanitation, Cleaning & Pest Management · Cleaning-in-place: design, cycles and the Sinner circle

3. What surface roughness is commonly specified for hygienic food-contact stainless steel?

  1. Roughness does not matter if sanitiser is used
  2. Ra of about 80 µm
  3. Ra of about 0.8 µm or less
  4. Ra of about 8 µm or more
Answer and working

C. Ra of about 0.8 µm or less

Hygienic-design guidance commonly specifies Ra ≤ about 0.8 µm so that surfaces clean easily; rougher finishes trap soil and bacteria. Sanitiser cannot compensate for poor surface finish.

Food Plant Sanitation, Cleaning & Pest Management · Biofilm control

4. Why must bearings and lubrication points on food machinery be placed outside the product zone, with food-grade lubricants where incidental contact is possible?

  1. To keep lubricant and wear debris out of the food
  2. Because food-grade lubricants are cheaper than other lubricants
  3. Because bearings inside the product zone run too cold to turn
  4. To make bearings easier to paint during annual maintenance
Answer and working

A. To keep lubricant and wear debris out of the food

Bearings shed lubricant and metal particles; keeping them outside the product zone and using lubricants registered for incidental food contact limits chemical and physical contamination. Temperature, price and painting are not the reason.

Food Plant Design, Hygienic Engineering, Utilities & Automation · Hygienic design of equipment: EHEDG and 3-A principles

5. A floor slopes to a drain at a fall of 1 in 50. How much lower is the floor at the drain than at a point 6 m away?

  1. 120 mm
  2. 300 mm
  3. 12 mm
  4. 60 mm
Answer and working

A. 120 mm

Fall = run ÷ 50 = 6,000 mm ÷ 50 = 120 mm. A 1-in-100 fall would give 60 mm; 300 mm multiplies instead of divides; 12 mm is a factor-of-ten slip. Falls of about 1 in 50 to 1 in 100 are common, steeper in very wet areas.

Food Plant Design, Hygienic Engineering, Utilities & Automation · Hygienic design of buildings: floors, drains, walls and air handling

6. What is a dead leg in a hygienic pipeline?

  1. A pipe branch that has been fitted with a mix-proof double-seat valve
  2. A support bracket that carries the weight of a vertical pipe run
  3. A stagnant pipe section that cleaning flow cannot reach
  4. A pipe section that slopes downward in the direction of product flow
Answer and working

C. A stagnant pipe section that cleaning flow cannot reach

A dead leg is a stagnant branch, such as a capped tee, which CIP flow does not sweep, so soil and biofilm build up. Supports, falls in the flow direction and double-seat valves are normal hygienic features, not dead legs.

Food Plant Design, Hygienic Engineering, Utilities & Automation · Hygienic design of equipment: EHEDG and 3-A principles

7. What is the purpose of an air gap or reduced-pressure-zone valve on a water supply to equipment?

  1. To stop backflow into the potable supply
  2. To remove chlorine before use
  3. To raise the water pressure for cleaning
  4. To heat the water for sanitising
Answer and working

A. To stop backflow into the potable supply

Backflow prevention stops contaminated liquid being siphoned or pushed back into potable pipes through hoses or equipment connections. It does not change pressure, temperature or chlorine.

Food Plant Sanitation, Cleaning & Pest Management · Water hygiene in food plants

8. Metal detectors are commonly placed after conveying and size-reduction steps because

  1. metal detectors usually also measure product moisture and salt content
  2. they replace the need for any cleaning
  3. worn screws, blades and belts shed foreign bodies
  4. conveyors magnetise all food products
Answer and working

C. worn screws, blades and belts shed foreign bodies

Wear of moving parts is a known source of metal contamination; detectors catch it before packing.

Mechanical Unit Operations: Size Reduction, Mixing & Separation · Material handling: conveyors and elevators for foods

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock all 37 questions — EHEDG hygienic design training

US$10 a month · one price worldwide · cancel any time

  • Every practice question for this course, with explanations
  • Timed papers for the exams this course leads to
  • Ask Laisha to explain any topic — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.