LAISHA
Open Laisha

EHEDG hygienic design training Food Plant Design, Hygienic Engineering, Utilities & Automation: practice questions

EHEDG hygienic design training · International (Europe-based) · European Hygienic Engineering & Design Group

Original practice questions written to the published syllabus · not past papers
10worked here, free
20written to this exam in this subject
3syllabus units

About EHEDG hygienic design training

EHEDG hygienic design training is a professional certification run by European Hygienic Engineering & Design Group, for candidates worldwide. Hygienic design courses and certificates for engineers and food technologists.

Official site: ehedg.org.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Food Plant Design, Hygienic Engineering, Utilities & Automation in EHEDG hygienic design training

Turning a process into a plant that is hygienic, efficient and safe: hygienic equipment and building design, plant layout, process flow and equipment selection, steam, water, compressed air and refrigeration utilities, instrumentation and automation, energy audit and scale-up. Agricultural Engineering's food-quality-safety-plant-design covers plant location, layout and feasibility reports; this subject adds hygienic engineering (EHEDG and 3-A principles), utilities, automation and energy management in depth.

Our 20 EHEDG hygienic design training questions in this subject: 6 easy, 12 medium, 2 hard, across 3 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to EHEDG hygienic design training and are not shown on any other exam's page.

Question 1 · medium

In a ready-meal plant, where is the boundary between low-risk and high-risk areas ideally placed?

  1. At the goods-inwards dock, because raw materials are the only source of contamination in the plant
  2. At the canteen entrance, so that staff change clothing only at meal breaks and not between rooms
  3. At the lethal step itself, such as a through-wall oven loaded on the raw side and emptied on the cooked side
  4. At the dispatch door, so that all production rooms share one zone and staff can move freely inside it
Answer and working

C. At the lethal step itself, such as a through-wall oven loaded on the raw side and emptied on the cooked side

The best barrier is the cooking equipment: raw product enters on the low-risk side and cooked product leaves on the high-risk side, so nothing crosses the wall uncooked. A single shared zone or a boundary at the canteen or dock leaves cooked product exposed to raw-side contamination.

Question 2 · medium

Why should overhead service pipes and cable trays not pass above exposed product?

  1. Overhead services always raise the room's air-conditioning load
  2. They interfere with the radio signals used by handheld scanners
  3. Dust, drips and condensation from them could fall into the product
  4. Food law forbids any pipe from crossing above a production floor
Answer and working

C. Dust, drips and condensation from them could fall into the product

Pipework and trays above product collect dust and form condensation that can drip into food; services are routed outside the product zone or above walk-on ceilings. Radio interference and air-conditioning load are not the issue, and overhead pipes are allowed where they do not pass over exposed product.

Question 3 · easy

Which two bodies publish the most widely used hygienic design criteria for food processing equipment?

  1. ISA and IEC 61131-3 committees
  2. EHEDG and 3-A Sanitary Standards
  3. ISO 50001 and ISO 8573-1 committees
  4. WOAH and Codex Alimentarius
Answer and working

B. EHEDG and 3-A Sanitary Standards

The European Hygienic Engineering and Design Group and 3-A Sanitary Standards Inc. publish guidelines, standards and certification for hygienic equipment; ISO 14159 and EN 1672-2 cover machinery hygiene. ISO 50001 is energy management, ISO 8573-1 air quality, WOAH animal health, and ISA/IEC 61131-3 automation.

Question 4 · medium

Why is a mix-proof double-seat valve used where product and cleaning lines meet?

  1. A leakage chamber vented to drain between two seats keeps a seat leak from mixing them
  2. Its single ball with a central cavity traps any leaking detergent until shutdown
  3. It is the cheapest valve available and needs no cleaning of its own seats or chamber
  4. It lets product and cleaning solution flow together at a controlled ratio during production
Answer and working

A. A leakage chamber vented to drain between two seats keeps a seat leak from mixing them

Between the two seats is a chamber vented to drain; if either seat leaks, the leak shows at the drain instead of contaminating product. Mixing the fluids is exactly what it prevents; it is costly and its seats are cleaned by seat-lifting; ball valves with cavities are unhygienic.

Question 5 · hard

Welds in product-contact pipework are found to be uneven with incomplete penetration on the inside. Why is this a hygiene problem?

  1. Rough welds raise the pipe's surface roughness only on the outside, which is unimportant
  2. Uneven welds increase pipe pressure drop so much that product flow stops entirely
  3. Crevices and rough internal beads harbour soil and bacteria that cleaning cannot remove
  4. Incomplete penetration makes the pipe magnetic, which upsets metal detectors downstream
Answer and working

C. Crevices and rough internal beads harbour soil and bacteria that cleaning cannot remove

Product-zone welds must be continuous, full-penetration and ground flush, ideally orbital-welded, because pits and crevices inside the pipe hold soil and biofilm out of reach of cleaning. The pressure-drop effect is small, welds do not make austenitic steel a detection issue downstream, and the defect described is on the inside.

Question 6 · medium

Which elastomers are commonly used for hygienic seals and gaskets in food equipment?

  1. Untreated rubber and felt
  2. Natural cork, felt and leather pads
  3. Asbestos fibre and graphite
  4. EPDM, FKM, silicone and PTFE
Answer and working

D. EPDM, FKM, silicone and PTFE

Approved elastomers and plastics such as EPDM, FKM, silicone and PTFE resist product, cleaning chemicals and temperature. Cork, leather and felt are absorbent; asbestos is banned; untreated rubber degrades.

Question 7 · easy

Why must bearings and lubrication points on food machinery be placed outside the product zone, with food-grade lubricants where incidental contact is possible?

  1. To keep lubricant and wear debris out of the food
  2. Because food-grade lubricants are cheaper than other lubricants
  3. Because bearings inside the product zone run too cold to turn
  4. To make bearings easier to paint during annual maintenance
Answer and working

A. To keep lubricant and wear debris out of the food

Bearings shed lubricant and metal particles; keeping them outside the product zone and using lubricants registered for incidental food contact limits chemical and physical contamination. Temperature, price and painting are not the reason.

Question 8 · medium

A floor slopes to a drain at a fall of 1 in 50. How much lower is the floor at the drain than at a point 6 m away?

  1. 120 mm
  2. 300 mm
  3. 12 mm
  4. 60 mm
Answer and working

A. 120 mm

Fall = run ÷ 50 = 6,000 mm ÷ 50 = 120 mm. A 1-in-100 fall would give 60 mm; 300 mm multiplies instead of divides; 12 mm is a factor-of-ten slip. Falls of about 1 in 50 to 1 in 100 are common, steeper in very wet areas.

Question 9 · medium

Which window arrangement is appropriate in a production area?

  1. Few windows, fixed or insect-screened, with shatterproof glazing or film
  2. Windows with deep internal sills on which tools can be kept handy
  3. Ordinary float glass, which is acceptable if a glass register is kept
  4. Large openable windows without screens to give natural ventilation
Answer and working

A. Few windows, fixed or insect-screened, with shatterproof glazing or film

Glass breakage is a foreign-body hazard and open windows admit pests and dust, so windows are minimised, fixed or screened and protected against shattering. A register does not make ordinary glass safe, and sills collect dust.

Question 10 · medium

High-care rooms are kept at positive air pressure relative to adjacent areas. What does this achieve?

  1. Air flows outward through openings, so unfiltered air from less clean areas does not enter
  2. It raises the boiling point of water in the room so that cleaning is more effective
  3. Air flows inward from the corridor, carrying fresh air from outside across exposed product
  4. It keeps the room's humidity at zero, which prevents any condensation forming on surfaces
Answer and working

A. Air flows outward through openings, so unfiltered air from less clean areas does not enter

Supplying more filtered air than is extracted makes air leak outward through doors and gaps, keeping less clean air out. The pressure difference is tiny and does not change boiling point or remove all humidity.

A study plan for Food Plant Design, Hygienic Engineering, Utilities & Automation in EHEDG hygienic design training

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (45% of the 20 questions): Hygienic design of buildings: floors, drains, walls and air handling (9, 45%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Hygienic design of equipment: EHEDG and 3-A principles (8, 40%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Plant layout: product, process and hygienic zoning (3, 15%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Hygienic design of equipment: EHEDG and 3-A principles (1 hard of 8), Hygienic design of buildings: floors, drains, walls and air handling (1 hard of 9).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Hygienic design of equipment: EHEDG and 3-A principles (3 easy of 8); Hygienic design of buildings: floors, drains, walls and air handling (3 easy of 9).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — EHEDG hygienic design training Food Plant Design, Hygienic Engineering, Utilities & Automa

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.