LAISHA
Open Laisha

ICAR AIEEA-PG / PGS Food Plant Design, Hygienic Engineering, Utilities & Automation: practice questions

ICAR AIEEA-PG / PGS — Code 18 Food Science Technology · India · ICAR through the National Testing Agency

Original practice questions written to the published syllabus · not past papers
10worked here, free
111written to this exam in this subject
15syllabus units

About ICAR AIEEA-PG / PGS

ICAR AIEEA-PG / PGS — Code 18 Food Science Technology is a postgraduate admission exam run by ICAR through the National Testing Agency, for candidates in India. Computer-based, multiple choice, +4/−1 marking.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Food Plant Design, Hygienic Engineering, Utilities & Automation in ICAR AIEEA-PG / PGS

Turning a process into a plant that is hygienic, efficient and safe: hygienic equipment and building design, plant layout, process flow and equipment selection, steam, water, compressed air and refrigeration utilities, instrumentation and automation, energy audit and scale-up. Agricultural Engineering's food-quality-safety-plant-design covers plant location, layout and feasibility reports; this subject adds hygienic engineering (EHEDG and 3-A principles), utilities, automation and energy management in depth.

Our 111 ICAR AIEEA-PG / PGS questions in this subject: 42 easy, 54 medium, 15 hard, across 15 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG / PGS and are not shown on any other exam's page.

Question 1 · medium

What is a dead leg in a hygienic pipeline?

  1. A pipe branch that has been fitted with a mix-proof double-seat valve
  2. A support bracket that carries the weight of a vertical pipe run
  3. A stagnant pipe section that cleaning flow cannot reach
  4. A pipe section that slopes downward in the direction of product flow
Answer and working

C. A stagnant pipe section that cleaning flow cannot reach

A dead leg is a stagnant branch, such as a capped tee, which CIP flow does not sweep, so soil and biofilm build up. Supports, falls in the flow direction and double-seat valves are normal hygienic features, not dead legs.

Question 2 · medium

An open conveyor frame is being specified. Which construction meets hygienic design principles?

  1. Box sections and angle iron welded into a closed frame that keeps water out of the interior
  2. Open frame of round tubes, minimal horizontal surfaces and floor clearance for cleaning beneath
  3. A frame sitting flush on the floor so that nothing can get underneath it during production
  4. Flat horizontal shelves under the belt to collect fallen product for later recovery
Answer and working

B. Open frame of round tubes, minimal horizontal surfaces and floor clearance for cleaning beneath

Round tubes shed water and soil, open frames can be seen and cleaned, and clearance from the floor allows cleaning beneath. Hollow box sections and angle iron trap soil and are hard to inspect, horizontal ledges collect debris, and frames flush to the floor create inaccessible crevices.

Question 3 · medium

Why are low-carbon 'L' grades such as 316L specified for welded food equipment?

  1. Less carbon means no chromium carbides form at grain boundaries when welded
  2. L grades are non-magnetic only after welding, which helps metal detectors
  3. L grades contain extra copper that protects welds from lactic acid attack
  4. Low carbon makes the steel soft enough to weld without any filler metal at all
Answer and working

A. Less carbon means no chromium carbides form at grain boundaries when welded

In standard grades, heat from welding can precipitate chromium carbides at grain boundaries, depleting chromium and causing intergranular corrosion (sensitisation). Low carbon prevents this. The other claims about softness, copper and magnetism are false.

Question 4 · medium

Why are drains a particular concern in ready-to-eat food plants?

  1. They are major harbourage sites for Listeria, which splashes and aerosols then spread
  2. They are only a concern for odours, which affect staff comfort but not food safety
  3. They are the main source of Clostridium botulinum spores in finished canned products
  4. They concentrate heavy metals from cleaning chemicals, which then volatilise into air
Answer and working

A. They are major harbourage sites for Listeria, which splashes and aerosols then spread

Listeria persists in wet drains and is spread by splashing and high-pressure hosing; drains are sited away from equipment, trapped, cleaned and sanitised. Botulinum in canned food is controlled by the thermal process, and drains are a microbial hazard, not just an odour issue.

Question 5 · hard

Condensation forms on a ceiling above an open product conveyor. Which combination of measures addresses the cause?

  1. Increase hosing of the ceiling during production so that droplets are washed away
  2. Lower the room temperature further, so that the ceiling becomes even colder
  3. Insulate cold surfaces, control room humidity and maintain adequate air movement
  4. Fit a horizontal ledge below the ceiling to catch the droplets before they fall
Answer and working

C. Insulate cold surfaces, control room humidity and maintain adequate air movement

Condensation forms where surfaces are below the air's dew point; insulation, humidity control and air movement prevent it. Hosing during production makes aerosols and more moisture, colder surfaces worsen condensation, and ledges collect water and soil.

Question 6 · easy

Where are HEPA filters typically used in food plants?

  1. On compressor intakes to remove water vapour
  2. In boiler flues, where they can remove carbon dioxide
  3. Over aseptic fillers and in some high-care rooms
  4. In effluent lines to remove fats and grease
Answer and working

C. Over aseptic fillers and in some high-care rooms

High-efficiency particulate air filters are used where the highest air cleanliness is required, such as aseptic filling. They do not remove gases such as CO2 or water vapour and are not used on liquid effluent.

Question 7 · easy

Which boiler type passes hot combustion gases through tubes immersed in a large water shell and is common in small and medium food plants?

  1. Water-tube boiler
  2. Once-through (supercritical) boiler
  3. Electrode boiler
  4. Fire-tube (shell) boiler
Answer and working

D. Fire-tube (shell) boiler

In fire-tube boilers the gases pass through tubes surrounded by water; the large water volume buffers load changes and suits small and medium plants at moderate pressures. Water-tube boilers carry water inside tubes and handle higher pressures and capacities.

Question 8 · easy

A refrigeration plant is rated at 100 tonnes of refrigeration (TR). What is its capacity in kilowatts?

  1. 3,517 kW
  2. 352 kW
  3. 100 kW
  4. 28 kW
Answer and working

B. 352 kW

1 TR = 3.517 kW (12,000 Btu/h), so 100 TR = 352 kW. 3,517 kW is a decimal-place slip and 28 kW divides instead of multiplies.

Question 9 · easy

Which temperature sensor is standard for pasteuriser and retort control because of its accuracy and stability?

  1. Bimetallic strip thermostat
  2. Infrared surface thermometer
  3. Pt100 platinum RTD
  4. Liquid-in-glass thermometer
Answer and working

C. Pt100 platinum RTD

Pt100 RTDs are accurate and stable and are the norm for critical thermal processes. Bimetallic devices are crude, glass is a breakage hazard in production, and infrared measures surfaces, not the product stream.

Question 10 · easy

Which control mode suits a cold-room temperature where a small swing about the set point is acceptable?

  1. Cascade control
  2. Ratio control
  3. Model predictive control
  4. On/off control
Answer and working

D. On/off control

On/off control switches the compressor fully on or off, cycling within a dead band; it is simple and adequate where some swing is acceptable. Cascade, predictive and ratio control are for more demanding or different duties.

A study plan for Food Plant Design, Hygienic Engineering, Utilities & Automation in ICAR AIEEA-PG / PGS

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (42% of the 111 questions): Compressed air and refrigeration utilities (10, 9%); Steam generation and distribution (10, 9%); Energy audit and energy conservation (9, 8%); Hygienic design of buildings: floors, drains, walls and air handling (9, 8%); Hygienic design of equipment: EHEDG and 3-A principles (9, 8%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Materials of construction and corrosion in food plants (8, 7%); Plant layout: product, process and hygienic zoning (8, 7%); Process control: feedback loops, PID and PLC/SCADA (8, 7%); Instrumentation and sensors in food plants (7, 6%); Process flow diagrams and piping and instrumentation diagrams (6, 5%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Project feasibility and costing of a food plant (6, 5%); Water supply and treatment for food plants (6, 5%); Online data acquisition and digital plants (5, 5%); Plant location and site selection (5, 5%); Scale-up and pilot plants (5, 5%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Steam generation and distribution (3 hard of 10), Process control: feedback loops, PID and PLC/SCADA (2 hard of 8), Compressed air and refrigeration utilities (2 hard of 10).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Plant layout: product, process and hygienic zoning (4 easy of 8); Process flow diagrams and piping and instrumentation diagrams (3 easy of 6).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG / PGS Food Plant Design, Hygienic Engineering, Utilities & Automation

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.