LAISHA
Open Laisha

ICAR AIEEA-PG / PGS Mechanical Unit Operations: Size Reduction, Mixing & Separation: practice questions

ICAR AIEEA-PG / PGS — Code 18 Food Science Technology · India · ICAR through the National Testing Agency

Original practice questions written to the published syllabus · not past papers
10worked here, free
70written to this exam in this subject
15syllabus units

About ICAR AIEEA-PG / PGS

ICAR AIEEA-PG / PGS — Code 18 Food Science Technology is a postgraduate admission exam run by ICAR through the National Testing Agency, for candidates in India. Computer-based, multiple choice, +4/−1 marking.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Mechanical Unit Operations: Size Reduction, Mixing & Separation in ICAR AIEEA-PG / PGS

Unit II lists cleaning, de-husking, sorting and grading, peeling, size reduction, mixing and forming, separation, filtration and membrane processes, expression, extraction and leaching, crystallisation and distillation. MCQs test principles, equipment types and applications (hammer vs roller mills, disc-stack vs decanter, MF/UF/NF/RO, filter aids, flash-steam vs lye peeling) and short calculations.

The mechanical operations that clean, sort, reduce, mix, homogenise and separate food materials, including filtration, centrifugation and membrane processes, with the design equations used to size them.

Our 70 ICAR AIEEA-PG / PGS questions in this subject: 17 easy, 51 medium, 2 hard, across 15 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG / PGS and are not shown on any other exam's page.

Question 1 · easy

Hammer mills reduce size mainly by

  1. impact
  2. cutting with sharp knives
  3. compression between smooth rolls
  4. attrition between stones
Answer and working

A. impact

High-speed swinging hammers shatter brittle materials by impact; a screen controls product size.

Question 2 · medium

Wheat flour milling relies mainly on

  1. hammer mills with fine screens only
  2. roller mills combining compression and shear
  3. colloid mills with a narrow rotor–stator gap for each stream
  4. bowl choppers with rotating knives
Answer and working

B. roller mills combining compression and shear

Pairs of fluted break rolls and smooth reduction rolls, running at different speeds, separate endosperm from bran gradually.

Question 3 · medium

Segregation in dry-mix blending is most likely when ingredients differ greatly in

  1. flavour
  2. particle size and density
  3. country of origin
  4. packaging
Answer and working

B. particle size and density

Small or dense particles percolate downward during handling; matching sizes and adding a little liquid reduce segregation.

Question 4 · medium

Static mixers are

  1. impellers driven by variable-speed motors mounted above an open tank
  2. tumbling drums for powders
  3. fixed elements inside a pipe that divide and recombine the flow
  4. vessels heated by steam jackets
Answer and working

C. fixed elements inside a pipe that divide and recombine the flow

They mix continuously with no moving parts, using the energy of the flowing fluid.

Question 5 · hard

A starch granule 20 µm in diameter (ρ = 1,500 kg/m³) settles in water (ρ = 1,000 kg/m³, μ = 0.001 Pa s). Its Stokes settling velocity is closest to

  1. 3.27e-04 m/s
  2. 5.45e+00 m/s
  3. 1.09e-04 m/s
  4. 1.09e-07 m/s
Answer and working

C. 1.09e-04 m/s

v = d²(ρp − ρf)g/18μ = (2 × 10⁻⁵)² × 500 × 9.81/0.018 = 1.09e-04 m/s. Using ρp instead of the density difference triples it; using d instead of d² is far too large; μ = 1.0 Pa s confuses mPa s.

Question 6 · hard

A centrifuge bowl of radius 0.2 m spins at 6,000 rpm. The relative centrifugal force (g-number) is closest to

  1. 8,049
  2. 733,945
  3. 12.8
  4. 78,957
Answer and working

A. 8,049

ω = 2π × 6,000/60 = 628 rad/s; rω²/g = 0.2 × 628²/9.81 = 8,049. The first uses rpm instead of rad/s; 12.8 uses ω not ω²; 78,957 forgets to divide by g.

Question 7 · medium

A solute has concentration 40 g/L in the feed and 0.6 g/L in the permeate. Its rejection coefficient R = 1 − Cp/Cf is

  1. 0.985
  2. 0.015
  3. 66.7
  4. 0.600
Answer and working

A. 0.985

R = 1 − 0.6/40 = 0.985. 0.015 is Cp/Cf; 66.7 inverts it; 0.600 confuses permeate concentration with rejection.

Question 8 · medium

Fondant and sweetened condensed milk must have very small crystals because

  1. small crystals dissolve sugar faster in the mouth only
  2. large crystals ferment more quickly
  3. large crystals give a gritty, sandy texture
  4. small crystals raise the product's pH
Answer and working

C. large crystals give a gritty, sandy texture

Crystals below about 10–20 µm are not detected as grittiness; seeding and controlled cooling keep them small.

Question 9 · easy

The critical point of carbon dioxide used in supercritical extraction is about

  1. 31 °C and 7.4 MPa
  2. 100 °C and 0.1 MPa
  3. 374 °C and 22 MPa
  4. −78 °C and 0.1 MPa
Answer and working

A. 31 °C and 7.4 MPa

CO₂ critical point is about 31.1 °C and 7.38 MPa; 374 °C and 22 MPa is water's; −78.5 °C is the CO₂ sublimation point at atmospheric pressure.

Question 10 · medium

Continuous-discharge bucket elevators are preferred to centrifugal-discharge types for

  1. free-flowing grains at high speed
  2. fragile or dusty materials
  3. liquids
  4. packaged cartons
Answer and working

B. fragile or dusty materials

They run slower, and material slides off onto the preceding bucket, reducing damage and dust.

A study plan for Mechanical Unit Operations: Size Reduction, Mixing & Separation in ICAR AIEEA-PG / PGS

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (40% of the 70 questions): Membrane processes: microfiltration, ultrafiltration, nanofiltration and reverse osmosis (7, 10%); Mixing of solids, pastes and liquids; agitation and power number (6, 9%); Centrifugation and centrifugal separators (5, 7%); Cleaning, sorting and grading of raw materials (5, 7%); Crystallisation (5, 7%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Expression and solid-liquid extraction (5, 7%); Size reduction: energy laws of Rittinger, Kick and Bond (5, 7%); Size-reduction equipment for dry and wet foods (5, 7%); Distillation and supercritical fluid extraction (4, 6%); Filtration: cake filtration theory and filter aids (4, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: High-pressure homogenisation (4, 6%); Material handling: conveyors and elevators for foods (4, 6%); Peeling methods (4, 6%); Settling and sedimentation (4, 6%); Sieving and particle-size analysis (3, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Settling and sedimentation (1 hard of 4), Centrifugation and centrifugal separators (1 hard of 5).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Cleaning, sorting and grading of raw materials (2 easy of 5); Sieving and particle-size analysis (1 easy of 3).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG / PGS Mechanical Unit Operations: Size Reduction, Mixing & Separation

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.