ICAR AIEEA-PG / PGS — Code 18 Food Science Technology · India · ICAR through the National Testing Agency
Original practice questions written to the published syllabus · not past papers
10worked here, free
64written to this exam in this subject
9syllabus units
About ICAR AIEEA-PG / PGS
ICAR AIEEA-PG / PGS — Code 18 Food Science Technology is a postgraduate admission exam run by ICAR through the National Testing Agency, for candidates in India. Computer-based, multiple choice, +4/−1 marking.
The practical semester most food technology degrees require: work in a food plant or laboratory, an experiential-learning unit that makes and sells a product, and a project or capstone that takes one problem from question to report.
Our 64 ICAR AIEEA-PG / PGS questions in this subject: 24 easy, 39 medium, 1 hard, across 9 units.
10 practice questions, worked
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AIEEA-PG / PGS and are not shown on any other exam's page.
Question 1 · easy
Which learning objective is written in SMART form?
Learn about the dairy industry in general terms
Understand everything about food safety during the placement
By week four, map the milk line and its CCPs unaided
Become a good food technologist by the end of the year
Answer and working
C. By week four, map the milk line and its CCPs unaided
A SMART objective is specific, measurable, achievable, relevant and time-bound; the other options are vague and unmeasurable.
Question 2 · medium
What does document control in a quality system ensure?
Documents are never changed once they have been written
Only current versions are in use
All documents are kept secret from the production staff
Only senior managers may read the written procedures
Answer and working
B. Only current versions are in use
Document control approves, issues and withdraws documents so that obsolete versions are not used.
Question 3 · medium
In a mass balance for a steady continuous process, what is assumed about accumulation?
It always equals the input
It is equal to the water evaporated
It equals the product flow
It is zero, so input equals output
Answer and working
D. It is zero, so input equals output
At steady state nothing builds up inside the system, so inflows equal outflows.
Question 4 · medium
Why are blanks and control samples run with each batch of analyses?
To increase the number of results reported each day
To use up surplus reagents before they expire
To replace the need for calibration of instruments
To detect contamination and confirm the method
Answer and working
D. To detect contamination and confirm the method
Blanks reveal reagent or glassware contributions; controls show whether the analytical system performs as expected. Instruments still need calibration.
Question 5 · medium
Why does the experiential unit assign roles such as production, quality, marketing and finance?
To let each student avoid any production work
Because the law requires four managers in every unit
To experience running a whole small enterprise
To make record keeping unnecessary for the group
Answer and working
C. To experience running a whole small enterprise
Role-based teams mirror a small company and teach how functions depend on each other.
Question 6 · medium
Which control point is critical when hot-filling jam into jars?
The number of jars per carton
The brand name on the lid
The colour of the fruit
Filling temperature and container treatment
Answer and working
D. Filling temperature and container treatment
Hot filling at a sufficient temperature with sterilised or hot containers and inversion controls post-process contamination; the others are not safety controls.
Question 7 · medium
For the same data (mean 3.30%, SD 0.16%), what is the CV?
0.16%
3.3%
48%
4.8%
Answer and working
D. 4.8%
CV = 0.158/3.30 × 100 = 4.8%. The other values confuse SD, mean or decimal places.
Question 8 · medium
What must the materials and methods section allow?
The student to avoid citing methods
Another person to repeat the work
The reader to skip the results
The results to be omitted
Answer and working
B. Another person to repeat the work
Methods give equipment, materials, conditions, replicates and statistics in enough detail to reproduce the study.
Question 9 · easy
A trainee has had diarrhoea the night before a production shift. What should they do?
Tell nobody to avoid losing a day
Wear two pairs of gloves and continue
Report it before entering production areas
Work as usual and wash hands more often
Answer and working
C. Report it before entering production areas
Illness must be reported so the trainee can be excluded or restricted, protecting the product.
Question 10 · easy
May a trainee post photographs of the production line on social media?
Yes, freely, at any time during the placement
Only with the host's permission
Yes, provided that all faces are blurred out
Yes, but only after the placement has ended
Answer and working
B. Only with the host's permission
Photographs can reveal confidential processes; permission is required.
A study plan for In-plant Training, Experiential Learning & Project in ICAR AIEEA-PG / PGS
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
First, the heavy units (41% of the 64 questions): Daily production and quality-control duties (9, 14%); Plant orientation: process flow, utilities and quality systems (9, 14%); Choosing a placement and setting learning objectives (8, 13%).
Read the manual chapters for these first and do every worked question you can find on them.
Then the middle band: Laboratory practice in an industry or regulatory laboratory (8, 13%); Professional conduct, safety and confidentiality (8, 13%); Experiential learning: running a small production unit (7, 11%).
Aim for one sitting per unit, then mixed questions across them.
Then the lighter units: Report writing and presentation (7, 11%); Data collection and analysis (4, 6%); Project planning and literature review (4, 6%).
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Leave time for the hard ones: Plant orientation: process flow, utilities and quality systems (1 hard of 9).
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Bank the easy marks: Choosing a placement and setting learning objectives (4 easy of 8); Data collection and analysis (2 easy of 4).
Do these early in revision so they are fast on the day.
Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.