ICAR AICE-JRF/SRF In-plant Training, Experiential Learning & Project: practice questions
ICAR AICE-JRF/SRF (PhD) — Food Processing Technology, Food Safety & Quality, Processing and Food Engineering · India · ICAR through the National Testing Agency
Original practice questions written to the published syllabus · not past papers
10worked here, free
21written to this exam in this subject
9syllabus units
About ICAR AICE-JRF/SRF
ICAR AICE-JRF/SRF (PhD) — Food Processing Technology, Food Safety & Quality, Processing and Food Engineering is a PhD, fellowship and lectureship exam run by ICAR through the National Testing Agency, for candidates in India. Computer-based, multiple choice.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
In-plant Training, Experiential Learning & Project in ICAR AICE-JRF/SRF
The practical semester most food technology degrees require: work in a food plant or laboratory, an experiential-learning unit that makes and sells a product, and a project or capstone that takes one problem from question to report.
Our 21 ICAR AICE-JRF/SRF questions in this subject: 1 easy, 12 medium, 8 hard, across 9 units.
10 practice questions, worked
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.
Question 1 · medium
A tomato line uses more tomatoes than the solids balance predicts for its paste output. What does this indicate?
That the mass balance must always be wrong in practice
That tomatoes gain solids during processing
That the line is more efficient than anyone expected
Losses in peeling, pulping, cleaning or spills
Answer and working
D. Losses in peeling, pulping, cleaning or spills
The gap between theoretical and actual yield shows losses to investigate; solids are not created in processing.
Question 2 · hard
A duplicate pair of moisture results differs by more than the method's repeatability limit. What is the correct response?
Report the average of the two results anyway
Report only the lower of the two results obtained
Repeat it and look for the cause
Discard the method permanently and choose another
Answer and working
C. Repeat it and look for the cause
Exceeding the repeatability limit indicates an error or heterogeneity; the analysis is repeated and the cause sought before reporting.
Question 3 · hard
Customers report that the unit's biscuits taste rancid after three weeks. Which investigation is most useful?
Change the font and colour on the label
Increase the price of the biscuits to cover returns
Check fat quality, pack barrier and storage
Reduce the number of biscuits in each pack
Answer and working
C. Check fat quality, pack barrier and storage
Rancidity points to oxidation: fat freshness and stability, oxygen and light barrier of the pack, and storage conditions; antioxidants may help.
Question 4 · easy
What does a Gantt chart show?
The chemical structure of a compound
Tasks plotted against time with milestones
The organisation chart of a laboratory
Results of a sensory panel test
Answer and working
B. Tasks plotted against time with milestones
A Gantt chart shows when each task runs, how tasks overlap and when milestones fall.
Question 5 · medium
In a literature search, what does combining terms with AND do?
Excludes records containing the second term
Narrows results to records containing all terms
Broadens results to records containing any term
Sorts results by publication date
Answer and working
B. Narrows results to records containing all terms
AND requires all terms (narrowing); OR finds any (broadening); NOT excludes.
Question 6 · medium
How should a literature review be organised?
By themes, leading to the gap
By the alphabetical order of the authors only
By copying the abstracts of each paper one after another
As a list of unconnected summaries in date order
Answer and working
A. By themes, leading to the gap
A thematic, critical structure shows what is known, where studies disagree and why the project is needed.
Question 7 · medium
A student measures the viscosity of one yoghurt batch five times and treats these as five replicates. What is wrong?
Five readings are always too many for viscosity
Viscosity cannot be measured in a yoghurt at all
Readings of one batch are not true replicates
Nothing is wrong with this experimental design
Answer and working
C. Readings of one batch are not true replicates
True replicates are independent experimental units (separate batches); repeated readings measure only instrument precision.
Question 8 · hard
One result is far from the others with no recorded error. What should the student do?
Delete it silently to improve the final results
Replace it with the average of the other results
Investigate and report any exclusion
Repeat the experiment until the value disappears
Answer and working
C. Investigate and report any exclusion
Outliers are examined for causes; unexplained exclusion or replacement is poor practice and can be misconduct.
Question 9 · medium
What is the main purpose of a viva voce examination?
To test understanding and defence of the work
To re-measure the samples in front of the examiners
To grade the formatting of the references only
To decide the student's next placement host
Answer and working
A. To test understanding and defence of the work
Examiners check understanding, contribution and the ability to justify methods and conclusions.
Question 10 · hard
Why do employers rate professional behaviour so highly in trainees?
It is the only part of a degree that is ever assessed
Technical knowledge is never useful in food plants
Professional behaviour replaces the need for training
Reliability and communication earn responsibility
Answer and working
D. Reliability and communication earn responsibility
Trustworthy, communicative trainees can be given real tasks safely; technical knowledge remains essential.
A study plan for In-plant Training, Experiential Learning & Project in ICAR AICE-JRF/SRF
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
First, the heavy units (67% of the 21 questions): Data collection and analysis (6, 29%); Project planning and literature review (6, 29%); Professional conduct, safety and confidentiality (2, 10%).
Read the manual chapters for these first and do every worked question you can find on them.
Then the middle band: Report writing and presentation (2, 10%); Choosing a placement and setting learning objectives (1, 5%); Daily production and quality-control duties (1, 5%).
Aim for one sitting per unit, then mixed questions across them.
Then the lighter units: Experiential learning: running a small production unit (1, 5%); Laboratory practice in an industry or regulatory laboratory (1, 5%); Plant orientation: process flow, utilities and quality systems (1, 5%).
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Leave time for the hard ones: Choosing a placement and setting learning objectives (1 hard of 1), Daily production and quality-control duties (1 hard of 1), Experiential learning: running a small production unit (1 hard of 1).
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Bank the easy marks: Project planning and literature review (1 easy of 6).
Do these early in revision so they are fast on the day.
Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.