LAISHA
Open Laisha

ICAR AICE-JRF/SRF Thermal Processing & Canning Technology: practice questions

ICAR AICE-JRF/SRF (PhD) — Food Processing Technology, Food Safety & Quality, Processing and Food Engineering · India · ICAR through the National Testing Agency

Original practice questions written to the published syllabus · not past papers
10worked here, free
78written to this exam in this subject
14syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Food Processing Technology, Food Safety & Quality, Processing and Food Engineering is a PhD, fellowship and lectureship exam run by ICAR through the National Testing Agency, for candidates in India. Computer-based, multiple choice.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Thermal Processing & Canning Technology in ICAR AICE-JRF/SRF

35.a Unit 2 names thermal processing and process time evaluation for canned products, process optimisation and aseptic canning; 35.a Unit 1 names aseptic preservation; 35.b covers microbiological aspects of sterilisation and UHT. Expect general-method and formula-method reasoning, optimisation for quality (cook value, z of quality factors), particulate aseptic processing and regulatory concepts.

Designing and validating heat processes that make food safe and shelf-stable: microbial death kinetics, heat penetration, process calculation by the general and formula methods, retorts and aseptic systems, and the regulatory framework for low-acid canned foods. Agricultural Engineering's food-dairy-engineering introduces D, z and F; this subject teaches the full process-establishment practice.

Our 78 ICAR AICE-JRF/SRF questions in this subject: 7 easy, 48 medium, 23 hard, across 14 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · medium

An organism has D₁₁₀ = 3.0 min and z = 10 °C. Its D at 121.1 °C is closest to

  1. 38.6 min
  2. 3.33 min
  3. 2.70 min
  4. 0.23 min
Answer and working

D. 0.23 min

D₁₂₁.₁ = D₁₁₀ × 10^((110 − 121.1)/10) = 3.0 × 10^(−1.11) = 3.0 × 0.0776 = 0.23 min. 38.6 min uses the wrong sign, giving a larger D at a higher temperature, which is impossible; 3.33 and 2.70 min multiply or divide by the exponent 1.11 instead of by 10 raised to it.

Question 2 · hard

Using Ea ≈ 2.303 R T₁ T₂ / z with R = 8.314 J mol⁻¹ K⁻¹, the activation energy equivalent to z = 10 °C between 110 °C and 120 °C is closest to

  1. 125 kJ mol⁻¹
  2. 25.3 kJ mol⁻¹
  3. 288 kJ mol⁻¹
  4. 2.88 kJ mol⁻¹
Answer and working

C. 288 kJ mol⁻¹

Ea = 2.303 × 8.314 × 383.15 × 393.15 / 10 = 288424 J mol⁻¹ ≈ 288 kJ mol⁻¹. 125 kJ mol⁻¹ omits the 2.303; 25.3 kJ mol⁻¹ uses Celsius instead of kelvin; 2.88 is a unit slip by a factor of 100.

Question 3 · medium

Ball's calculated process time B is 46.2 min and the retort come-up time is 10 min. The operator's process time at retort temperature is closest to

  1. 36.2 min
  2. 50.4 min
  3. 41.6 min
  4. 42.0 min
Answer and working

D. 42.0 min

Ball credits 42 % of come-up as effective, so Pt = B − 0.42 × CUT = 46.2 − 4.2 = 42.0 min. 36.2 min subtracts the whole come-up; 50.4 min adds the credit instead of subtracting it; 41.6 min uses 46 % instead of 42 %.

Question 4 · medium

In Ball's formula B = fh log(jh Ih / g), if a product's fh doubles while everything else stays the same (including g), the process time B

  1. doubles, because B is directly proportional to fh
  2. halves, because faster heating is shown by a larger value of fh
  3. stays the same, because B depends only on jh and the initial temperature
  4. increases by log 2, because fh enters the formula inside the logarithm
Answer and working

A. doubles, because B is directly proportional to fh

fh multiplies the logarithmic term, so B is proportional to fh; a larger fh means slower heating. fh is outside the logarithm, not inside, and it is not an indicator of faster heating.

Question 5 · hard

Why is chlorinated or otherwise treated cooling water required for cans after retorting?

  1. Untreated water reacts with the internal lacquer and turns it yellow during long storage in the warehouse
  2. Contracting cans can draw water in through tiny seam gaps before the compound seals fully
  3. Treated water cools cans faster because chlorine raises its heat capacity
  4. Treated water is needed only to protect the retort from corrosion, not the food
Answer and working

B. Contracting cans can draw water in through tiny seam gaps before the compound seals fully

As cans cool, the internal pressure falls and a small leak can suck in water; treated water ensures it carries few microorganisms. Chlorine does not change heat capacity; yellowing and retort corrosion are not the reason for the requirement.

Question 6 · easy

The inner layer of a typical retortable pouch, which forms the heat seal, is usually made of

  1. polyester
  2. polypropylene
  3. aluminium foil
  4. nylon
Answer and working

B. polypropylene

Cast polypropylene is used as the sealant because it seals well and withstands retort temperatures. Polyester is the outer strength and print layer; aluminium foil is the barrier layer; nylon is sometimes added for puncture resistance, not sealing.

Question 7 · medium

In an aseptic line, a flow-diversion valve after the holding tube is required to

  1. divide the flow between two fillers so that each runs at half capacity
  2. release excess pressure from the holding tube whenever the product starts to boil inside it
  3. send product back for reprocessing automatically if outlet temperature falls below the set point
  4. add a measured dose of sterile water after the holding tube to standardise product solids before filling
Answer and working

C. send product back for reprocessing automatically if outlet temperature falls below the set point

Flow diversion ensures that product not held at the scheduled temperature never reaches the sterile filler. It is a safety device, not a flow splitter, pressure relief or dosing valve.

Question 8 · medium

Juice HACCP rules in the United States require processors to achieve a reduction of the most resistant pertinent pathogen of at least

  1. 3 log
  2. 5 log
  3. 12 log
  4. 1 log
Answer and working

B. 5 log

21 CFR 120 requires a 5-log reduction of the pertinent microorganism. 12 log is the botulinum criterion for low-acid canning; 1 and 3 log are too small.

Question 9 · medium

A processor wants to improve the colour of a convection-heating vegetable soup without reducing safety. Which change is most likely to help?

  1. Lower the retort temperature and lengthen the process to reach the same F₀ more gently over a longer time
  2. Reduce F₀ below the botulinum cook to shorten the process
  3. Process at a higher retort temperature with agitation for a shorter time to the same F₀
  4. Increase fill and reduce headspace so that the product moves less
Answer and working

C. Process at a higher retort temperature with agitation for a shorter time to the same F₀

Higher temperature and agitation give the same F₀ with less quality damage for convection products. Lowering temperature increases cooking; reducing F₀ below the safety target is unacceptable; less headspace reduces mixing and slows heating.

Question 10 · medium

Records required for each retort load of a low-acid canned food include

  1. the names and addresses of all the customers who will eventually buy the product
  2. the market price of tinplate on the day of production
  3. the sales forecast for the product line
  4. retort temperature records, reference thermometer readings and processing times
Answer and working

D. retort temperature records, reference thermometer readings and processing times

Processing records prove the scheduled process was delivered and are reviewed before release. Commercial information is not part of process records.

A study plan for Thermal Processing & Canning Technology in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (44% of the 78 questions): Thermal death kinetics: D value, z value and the thermal death time curve (8, 10%); Process calculation: Ball's formula method (7, 9%); Regulatory control of low-acid canned foods and process authorities (7, 9%); Aseptic processing and packaging (6, 8%); Can making, double seams and seam evaluation (6, 8%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Heat penetration tests and cold-spot determination (6, 8%); Retort pouches and flexible containers (6, 8%); Retort types: still, rotary, hydrostatic and continuous (6, 8%); Process calculation: the general method (5, 6%); Quality optimisation: cook value and nutrient retention (5, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Acid and low-acid foods; pH 4.6 and the target organism (4, 5%); Commercial sterility and spoilage probability (4, 5%); Lethality, F0 and the 12D concept (4, 5%); Pasteurisation of acid and acidified foods (4, 5%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Commercial sterility and spoilage probability (3 hard of 4), Process calculation: the general method (3 hard of 5), Lethality, F0 and the 12D concept (2 hard of 4).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Regulatory control of low-acid canned foods and process authorities (2 easy of 7); Can making, double seams and seam evaluation (1 easy of 6).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Thermal Processing & Canning Technology

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.