LAISHA
Open Laisha

ICAR AICE-JRF/SRF Transport Phenomena in Food Processing: Fluid Flow, Heat & Mass Transfer: practice questions

ICAR AICE-JRF/SRF (PhD) — Food Processing Technology, Food Safety & Quality, Processing and Food Engineering · India · ICAR through the National Testing Agency

Original practice questions written to the published syllabus · not past papers
10worked here, free
54written to this exam in this subject
15syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Food Processing Technology, Food Safety & Quality, Processing and Food Engineering is a PhD, fellowship and lectureship exam run by ICAR through the National Testing Agency, for candidates in India. Computer-based, multiple choice.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Transport Phenomena in Food Processing: Fluid Flow, Heat & Mass Transfer in ICAR AICE-JRF/SRF

41 Units 2 and 5 cover heat and mass transfer and design of processing machinery. Expect deeper questions on non-Newtonian flow, unsteady conduction and Heisler charts, effectiveness–NTU, and the heat–mass transfer analogy.

Mass and energy balances and the three transfer processes — momentum, heat and mass — applied to foods: pumping viscous products, heating cans and pouches, and moisture and gas movement through foods and packaging films.

Our 54 ICAR AICE-JRF/SRF questions in this subject: 0 easy, 29 medium, 25 hard, across 15 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · medium

Which of these is NOT dimensionally consistent as written?

  1. Q = m cp / ΔT
  2. Q = m cp ΔT
  3. Q = m λ
  4. Q = h A ΔT t
Answer and working

A. Q = m cp / ΔT

Heat (J) = kg × J/(kg K) × K; dividing by ΔT gives J/K², inconsistent. m λ gives J; hAΔT t gives J.

Question 2 · medium

In drying calculations, the component usually chosen as the 'tie' component is

  1. the water
  2. the air
  3. the volatile flavours
  4. the dry solids
Answer and working

D. the dry solids

Dry solids pass through unchanged, linking feed and product; water is what changes.

Question 3 · medium

As the saturation pressure of steam increases, its latent heat of vaporisation

  1. increases
  2. stays constant at 2,257 kJ/kg
  3. first doubles and then falls to zero
  4. decreases
Answer and working

D. decreases

hfg falls with rising pressure and temperature, reaching zero at the critical point; 2,257 kJ/kg applies at 100 °C.

Question 4 · medium

Orifice plates are seldom used to meter milk in hygienic process lines mainly because they

  1. cannot measure any liquid denser than water at room temperature
  2. work only at flows below 1 L/h
  3. measure temperature, not flow
  4. are hard to clean and cause permanent pressure loss
Answer and working

D. are hard to clean and cause permanent pressure loss

Orifices create crevices and dead zones and large permanent losses; magnetic and Coriolis meters are preferred for hygienic duty.

Question 5 · hard

For the milk at Re = 29,355 in a smooth 38 mm tube (ρ = 1,030 kg/m³, v = 1.5 m/s), using Blasius f = 0.0791 Re^−0.25 (Fanning), the pressure drop over 20 m is closest to

  1. 3.69 kPa
  2. 59 kPa
  3. 1.33 kPa
  4. 14.7 kPa
Answer and working

D. 14.7 kPa

f = 0.0791 × 29,355^−0.25 = 0.00604; ΔP = 4f(L/D)(ρv²/2) = 14,742 Pa ≈ 14.7 kPa. 3.69 kPa drops the factor 4 of the Fanning form; 59 kPa treats f as Fanning but applies an extra 4; 1.33 kPa wrongly uses the laminar f = 16/Re.

Question 6 · hard

Doubling the velocity of a Newtonian liquid in laminar flow through the same pipe changes the frictional pressure drop by a factor of

  1. 4
  2. 1.68
  3. 2
  4. 8
Answer and working

C. 2

Hagen–Poiseuille: ΔP ∝ v in laminar flow. In turbulent smooth-pipe flow (Blasius) ΔP ∝ v^1.75, about 3.4 times; 4 would apply to fully rough turbulent flow.

Question 7 · hard

A plant switches from pumping juice to pumping a thick fruit purée through the same line. Which change is most likely to be needed?

  1. Increase the pipe length to reduce pressure drop
  2. Lower the purée temperature so that its viscosity is reduced before pumping
  3. Replace the centrifugal pump with a positive-displacement pump
  4. Fit an orifice plate to measure the flow
Answer and working

C. Replace the centrifugal pump with a positive-displacement pump

Viscous, shear-thinning purées flow laminar with high pressure drop; centrifugal pumps lose efficiency badly, PD pumps handle them. Cooling raises viscosity; longer pipes raise pressure drop.

Question 8 · hard

Insulation (k = 0.04 W/m K) on a pipe extends from r1 = 25 mm to r2 = 50 mm. With 90 °C at the inner and 30 °C at the outer surface, the heat loss per metre is closest to

  1. 15.1 W/m
  2. 21.8 W/m
  3. 50 W/m
  4. 10.5 W/m
Answer and working

B. 21.8 W/m

q/L = 2πk(T1 − T2)/ln(r2/r1) = 2π × 0.04 × 60/ln 2 = 21.8 W/m. 15.1 W/m treats the layer as a flat wall of inner area; 50 W/m uses log₁₀; 10.5 W/m multiplies by ln 2.

Question 9 · hard

For the counter-current exchanger with LMTD 24.7 K, U = 1,500 W/m² K and area 10 m², the heat duty is closest to

  1. 370,000 kW
  2. 370 kW
  3. 375 kW
  4. 15 kW
Answer and working

B. 370 kW

Q = UA·LMTD = 1,500 × 10 × 24.66 = 369,946 W ≈ 370 kW. 370,000 kW forgets W→kW; 375 kW uses the arithmetic mean 25 K; 15 kW omits the LMTD.

Question 10 · medium

A process engineer finds that a CIP circuit gives a cleaning velocity of only 0.6 m/s in a 50 mm line. Since about 1.5 m/s is commonly recommended for turbulent cleaning, the flow should be increased by a factor of about

  1. 1.5
  2. 2.5
  3. 0.4
  4. 6.3
Answer and working

B. 2.5

Velocity ∝ flow in the same pipe: 1.5/0.6 = 2.5. 0.4 inverts it; 6.3 squares the ratio.

A study plan for Transport Phenomena in Food Processing: Fluid Flow, Heat & Mass Transfer in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (46% of the 54 questions): Heat exchangers: plate, tubular and scraped-surface; LMTD and effectiveness (6, 11%); Flow in pipes: Reynolds number, friction factor and pressure drop for Newtonian fluids (5, 9%); Flow of non-Newtonian foods in pipes (5, 9%); Unsteady-state heat transfer: lumped systems and Heisler charts (5, 9%); Convective mass transfer (4, 7%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Energy balances and steam tables (4, 7%); Permeability through single and multilayer films (4, 7%); Convection: film coefficients and dimensionless numbers (3, 6%); Fluid statics and the Bernoulli equation (3, 6%); Molecular diffusion and Fick's law (3, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Radiation heat transfer (3, 6%); Steady-state conduction through slabs, cylinders and composite walls (3, 6%); Units, dimensions and dimensional analysis (3, 6%); Pumps for foods: centrifugal and positive-displacement (2, 4%); Material balances on mixing, concentration and drying (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Heat exchangers: plate, tubular and scraped-surface; LMTD and effectiveness (5 hard of 6), Convection: film coefficients and dimensionless numbers (2 hard of 3), Steady-state conduction through slabs, cylinders and composite walls (2 hard of 3).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Transport Phenomena in Food Processing: Fluid Flow, Heat & Mass Transfer

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.