ICAR AICE-JRF/SRF (PhD) — Food Processing Technology, Food Safety & Quality, Processing and Food Engineering · India · ICAR through the National Testing Agency
Original practice questions written to the published syllabus · not past papersICAR AICE-JRF/SRF (PhD) — Food Processing Technology, Food Safety & Quality, Processing and Food Engineering is a PhD, fellowship and lectureship exam run by ICAR through the National Testing Agency, for candidates in India. Computer-based, multiple choice.
Source: icar.org.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
35.a Unit 2 names extruded products, breakfast and snack foods and texturised vegetable proteins; 41 covers process technology and machinery. Expect deeper questions on screw configuration, SME, RTD, starch fragmentation, high-moisture extrusion and co-extrusion.
The extruder as a continuous cooker and shaper: single- and twin-screw extruders, the transformations of starch and protein inside them, expanded snacks, breakfast cereals, pasta, and high-moisture extrusion for meat analogues.
Our 67 ICAR AICE-JRF/SRF questions in this subject: 9 easy, 35 medium, 23 hard, across 11 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.
A screw with D = 0.08 m turns at 2 rev/s with helix angle 17.7°; the channel is 0.06 m wide and 0.006 m deep. Using Qd = ½VzWH with Vz = πDN cos θ, the drag flow is closest to
B. 0.31 m³/h
Vz = π × 0.08 × 2 × cos 17.7° = 0.479 m/s; Qd = ½ × 0.479 × 0.06 × 0.006 = 8.62e-05 m³/s = 0.31 m³/h. Doubling omits the ½; omitting cos θ gives 0.33; the last leaves the value in m³/s.
Grooved barrels are used in single-screw food extruders to
A. prevent slip at the barrel wall
If material slips and turns with the screw, conveying fails; grooves grip it.
Using a die with smaller openings on the same extruder generally
B. raises die pressure and lowers output
A more restrictive die shifts the operating point along the screw characteristic.
Food twin-screw extruders commonly have length-to-diameter ratios of about
D. 20–40
L/D of roughly 20–40 allows feeding, cooking, venting and pressurising zones.
Vitamins are usually added to extruded cereals
A. after extrusion, by spraying or coating
Thiamin, vitamin C and folate are heat-sensitive and lost in the extruder.
A meat analogue needs 45 N to cut perpendicular to its fibres and 15 N parallel to them. Its anisotropy index is
B. 3.0
45/15 = 3.0; values above 1 indicate fibrousness. 0.33 inverts; 30 subtracts; 60 adds.
Switching to a different supplier's pea protein changes meat-analogue texture markedly. The best response is to
A. specify protein functionality and re-run extrusion trials
Protein solubility and gelling vary between ingredients; specifications and trials keep texture consistent.
Halving the radius of a circular die opening, other things equal, raises the die pressure drop by a factor of
C. 16
ΔP ∝ 1/R⁴; halving R multiplies ΔP by 2⁴ = 16.
Phase separation between protein-rich and water- or polysaccharide-rich phases in high-moisture extrusion is thought to
B. contribute to the layered, fibrous structure
Separated phases are elongated in the cooling die, adding anisotropy.
Dried pasta is dried to a final moisture of about
D. 12 %
Drying from about 30 % to about 12 % or below gives a stable product.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.