GATE XL Extrusion & Texturisation Technology: practice questions
GATE — Life Sciences (XL), Section U Food Technology · India · IITs and IISc on rotation (2027: IIT Madras)
Original practice questions written to the published syllabus · not past papers
10worked here, free
48written to this exam in this subject
11syllabus units
About GATE XL
GATE — Life Sciences (XL), Section U Food Technology is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks. MCQ, MSQ and NAT. Within XL, Section P Chemistry is understood to be compulsory and the candidate chooses two further sections, of which U Food Technology is one; this structure and the mark split are from earlier brochures and were not re-read for 2026.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Extrusion & Texturisation Technology in GATE XL
Same scope as XE-G; questions often link extrusion to starch and protein chemistry (gelatinisation at low moisture, fragmentation, protein texturisation).
The extruder as a continuous cooker and shaper: single- and twin-screw extruders, the transformations of starch and protein inside them, expanded snacks, breakfast cereals, pasta, and high-moisture extrusion for meat analogues.
Our 48 GATE XL questions in this subject: 19 easy, 16 medium, 13 hard, across 11 units.
10 practice questions, worked
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to GATE XL and are not shown on any other exam's page.
Question 1 · easy
The three functional zones of a cooking extruder screw are
mixing, freezing and drying
feed, transition and metering
washing, peeling and cutting
heating, holding and cooling
Answer and working
B. feed, transition and metering
Feed accepts material, transition compresses and melts it, metering pressurises it to the die.
Question 2 · medium
Net output of a single-screw extruder equals
pressure flow plus drag flow
the die flow multiplied by the screw speed in revolutions per second
drag flow minus pressure flow and leakage
leakage flow only
Answer and working
C. drag flow minus pressure flow and leakage
Back-pressure from the die opposes drag flow; leakage over flights reduces output further.
Question 3 · medium
An extrudate leaves the die at 2.0 m/s and is cut by a two-blade knife at 600 rpm. The piece length is about
20 cm
5 cm
0.3 cm
10 cm
Answer and working
D. 10 cm
Cuts per second = 600/60 × 2 = 20; length = 2.0/20 = 0.10 m = 10 cm. 20 cm ignores the second blade; 5 and 0.3 are slips.
Question 4 · hard
Bubble growth after the die stops when
the matrix cools below its glass transition
the cutter separates the pieces
all the starch becomes fully crystalline again at once
the product reaches 150 °C
Answer and working
A. the matrix cools below its glass transition
Loss of heat and water raises viscosity and sets the glassy structure.
Question 5 · easy
Specific mechanical energy in extrusion is
mechanical energy per unit mass extruded
heat supplied by barrel steam jackets per hour of running
the motor's rated power
the die pressure
Answer and working
A. mechanical energy per unit mass extruded
SME = shaft power / mass flow, in kJ/kg or kWh/t.
Question 6 · medium
Increasing feed moisture in starch extrusion usually
raises melt viscosity and SME
has no effect on viscosity
lowers melt viscosity and SME
stops the extruder
Answer and working
C. lowers melt viscosity and SME
Water plasticises the melt, reducing viscosity, die pressure and mechanical energy.
Question 7 · easy
Seasoning of expanded snacks is usually applied
inside the extruder before the die
after drying, with oil
to the raw grits before milling
during freezing of the snacks
Answer and working
B. after drying, with oil
Oil helps powders adhere after the pieces are dried; seasonings would burn in the barrel.
Question 8 · medium
Adding reverse-pitch elements to the screw profile of a co-rotating twin-screw extruder:
Raises local fill, shear and SME
Lowers residence time and reduces cooking
Converts the extruder to counter-rotating operation
Raises conveying capacity downstream of the element
Answer and working
A. Raises local fill, shear and SME
Reverse elements push material backwards, so the channels upstream fill completely, pressure builds, and shear and SME rise, giving more cooking. Residence time increases, not decreases. The screws still co-rotate. Reverse elements restrict conveying; they do not raise it.
Question 9 · medium
Fibrous whole-cut meat analogues are made by high-moisture extrusion. The feature that creates the aligned fibres is:
Rapid flashing of steam to vapour at the die exit
Grinding the extrudate after it leaves the die
A long cooling die in which the layered melt sets
Adding gluten after extrusion to bind the pieces
Answer and working
C. A long cooling die in which the layered melt sets
At 40 to 80% moisture the protein melt passes through a long cooled die; laminar flow orients the protein phases and cooling sets them before they can relax. Steam expansion at the die belongs to low-moisture TVP and gives a porous, spongy texture. Grinding destroys fibres. Gluten can be an ingredient, but adding it afterwards does not create fibres.
Question 10 · hard
At constant barrel temperature, raising feed moisture of a maize grit from 15% to 25% generally:
Increases expansion because more steam flashes off
Leaves expansion unchanged because moisture evaporates
Increases expansion because SME rises
Decreases expansion and raises bulk density
Answer and working
D. Decreases expansion and raises bulk density
Extra water plasticises the melt, lowering its viscosity and SME and dropping Tg, so bubbles collapse or shrink before the structure sets and the product is denser. More steam is available, but a weak melt cannot hold it. Moisture does change expansion strongly. SME falls, not rises, with more water.
A study plan for Extrusion & Texturisation Technology in GATE XL
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
First, the heavy units (52% of the 48 questions): Principles of extrusion cooking (7, 15%); Starch transformations during extrusion (7, 15%); Expanded snacks and ready-to-eat breakfast cereals (6, 13%); Specific mechanical energy and process variables (5, 10%).
Read the manual chapters for these first and do every worked question you can find on them.
Then the middle band: Die design and product shaping (4, 8%); Pasta and cold-forming extrusion (4, 8%); Quality evaluation of extrudates: expansion ratio and bulk density (4, 8%); Twin-screw extruders: configuration and screw elements (4, 8%).
Aim for one sitting per unit, then mixed questions across them.
Then the lighter units: Protein texturisation: low-moisture and high-moisture extrusion (3, 6%); Single-screw extruders: flow and pressure (3, 6%); Co-extrusion and filled products (1, 2%).
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Leave time for the hard ones: Co-extrusion and filled products (1 hard of 1), Starch transformations during extrusion (4 hard of 7), Specific mechanical energy and process variables (2 hard of 5).
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Bank the easy marks: Quality evaluation of extrudates: expansion ratio and bulk density (4 easy of 4); Principles of extrusion cooking (4 easy of 7).
Do these early in revision so they are fast on the day.
Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.