LAISHA
Open Laisha

GATE XL Thermal Processing & Canning Technology: practice questions

GATE — Life Sciences (XL), Section U Food Technology · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
62written to this exam in this subject
12syllabus units

About GATE XL

GATE — Life Sciences (XL), Section U Food Technology is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks. MCQ, MSQ and NAT. Within XL, Section P Chemistry is understood to be compulsory and the candidate chooses two further sections, of which U Food Technology is one; this structure and the mark split are from earlier brochures and were not re-read for 2026.

Source: gate2026.iitg.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Thermal Processing & Canning Technology in GATE XL

Same syllabus as XE-G Sections 3–4. Science graduates meet the same D, z, F and spoilage-probability calculations, usually framed through microbiology: target organisms, spore resistance, and the pH 4.6 boundary.

Designing and validating heat processes that make food safe and shelf-stable: microbial death kinetics, heat penetration, process calculation by the general and formula methods, retorts and aseptic systems, and the regulatory framework for low-acid canned foods. Agricultural Engineering's food-dairy-engineering introduces D, z and F; this subject teaches the full process-establishment practice.

Our 62 GATE XL questions in this subject: 18 easy, 35 medium, 9 hard, across 12 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE XL and are not shown on any other exam's page.

Question 1 · hard

D is 5.0 min at 112 °C and 0.8 min at 120 °C. The z value is closest to

  1. 12.6 °C
  2. 4.4 °C
  3. 1.9 °C
  4. 6.4 °C
Answer and working

A. 12.6 °C

z = (120 − 112)/log(5.0/0.8) = 8/0.796 = 12.6 °C. 4.4 °C uses the natural logarithm; 1.9 °C divides by the difference in D (5.0 − 0.8 = 4.2); 6.4 °C multiplies by the log instead of dividing.

Question 2 · medium

A process must give a 5-log reduction of a spoilage organism with D₁₂₁.₁ = 0.8 min. The required F₀ is

  1. 6.25 min
  2. 4.0 min
  3. 0.16 min
  4. 5.8 min
Answer and working

B. 4.0 min

F = D × log reductions = 0.8 × 5 = 4.0 min. 6.25 min divides 5 by 0.8; 0.16 min divides 0.8 by 5; 5.8 min adds D to the number of log cycles.

Question 3 · medium

On a plot of log(TR − T) against time, the straight part of a heating curve falls from TR − T = 50 °C at 12 min to 5 °C at 47 min. The heating rate index fh is

  1. 35 min
  2. 3.5 min
  3. 47 min
  4. 4.5 min
Answer and working

A. 35 min

fh is the time for one log cycle on the straight line; 50 → 5 °C is one cycle, taking 47 − 12 = 35 min. 47 min is the clock time, not the interval; 3.5 and 4.5 min are decimal and subtraction slips.

Question 4 · medium

With z = 10 °C, the lethal rate at a cold-spot temperature of 100 °C relative to 121.1 °C is closest to

  1. 0.2110
  2. 0.0100
  3. 0.2294
  4. 0.0078
Answer and working

D. 0.0078

L = 10^((100 − 121.1)/10) = 10^(−2.11) = 0.0078, so minutes near 100 °C add almost nothing to F₀. 0.2110 multiplies 21.1 by 0.01; 0.0100 uses a 20 °C difference instead of 21.1; 0.2294 uses z = 33 °C.

Question 5 · hard

Cold-spot readings taken every 2 minutes are 110, 116, 119, 120, 118 and 112 °C. With z = 10 °C, reference 121.1 °C and the trapezoidal rule, F₀ is closest to

  1. 4.6 min
  2. 2.3 min
  3. 4.8 min
  4. 9.2 min
Answer and working

A. 4.6 min

Lethal rates: 0.078, 0.309, 0.617, 0.776, 0.490, 0.123. F = Δt × (L₁/2 + L₂ + L₃ + L₄ + L₅ + L₆/2) = 2 × 2.292 = 4.58 min. 2.3 min forgets the 2-minute interval; 4.8 min gives the end points full weight; 9.2 min doubles the interval twice.

Question 6 · hard

Ball's method: fh = 40 min, jh = 1.4, initial temperature 70 °C, retort 121.1 °C, required F₀ = 6 min, and the fh/U table gives log g = 0.70. Ball's process time B is closest to

  1. 40.3 min
  2. 61.2 min
  3. 46.2 min
  4. 80.4 min
Answer and working

C. 46.2 min

Ih = 121.1 − 70 = 51.1; B = fh × (log(jh Ih) − log g) = 40 × (log 71.54 − 0.70) = 40 × (1.855 − 0.70) = 46.2 min. 40.3 min omits jh; 61.2 min uses the retort temperature instead of Ih; 80.4 min treats 0.70 as g rather than log g.

Question 7 · hard

Cans contain 100 spores each of a spoilage organism with D₁₂₁.₁ = 1.2 min. After a process delivering F₀ = 6 min, the expected number of spoiled cans in 200,000 is

  1. 2,000
  2. 20
  3. 1,000
  4. 200
Answer and working

D. 200

N = N₀ × 10^(−F/D) = 100 × 10^(−5) = 10⁻³ per can, so 200,000 × 10⁻³ = 200 spoiled cans. 2,000 and 20 miscount the log reductions by one either way; 1,000 uses the per-can probability inverted.

Question 8 · medium

Raising process temperature by 10 °C multiplies the lethal rate for spores (z = 10 °C) by 10. For a quality factor with z = 33 °C, the rate of destruction is multiplied by about

  1. 2.0
  2. 10.0
  3. 3.3
  4. 0.3
Answer and working

A. 2.0

10^(10/33) = 2.01. 10.0 applies to z = 10 °C; 3.3 divides 33 by 10; 0.3 is the exponent itself. Because quality reacts far less to temperature, HTST treatment gives the same lethality with less quality loss.

Question 9 · easy

Which vitamin is among the most heat-sensitive and is commonly used as an index of thermal damage in canned foods?

  1. Vitamin D
  2. Niacin
  3. Thiamin
  4. Vitamin K
Answer and working

C. Thiamin

Thiamin is very heat-labile and is a common index nutrient. Vitamin D, niacin and vitamin K are comparatively heat-stable.

Question 10 · medium

The cold spot of a can is held at 115 °C for 20 min. With z = 10 °C and a reference of 121.1 °C, the F₀ delivered is closest to:

  1. 4.9 min
  2. 20 min
  3. 2.0 min
  4. 81 min
Answer and working

A. 4.9 min

Lethal rate = 10^((115 − 121.1)/10) = 10^(−0.61) = 0.245, so F₀ = 0.245 × 20 = 4.9 min. 20 min ignores that 115 °C is less lethal than 121.1 °C. 2.0 min treats the 6.1 °C gap as a full 10 °C. 81 min divides by the lethal rate instead of multiplying.

A study plan for Thermal Processing & Canning Technology in GATE XL

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (53% of the 62 questions): Thermal death kinetics: D value, z value and the thermal death time curve (11, 18%); Lethality, F0 and the 12D concept (9, 15%); Acid and low-acid foods; pH 4.6 and the target organism (7, 11%); Commercial sterility and spoilage probability (6, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Aseptic processing and packaging (5, 8%); Heat penetration tests and cold-spot determination (5, 8%); Process calculation: the general method (5, 8%); Quality optimisation: cook value and nutrient retention (5, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Process calculation: Ball's formula method (3, 5%); Pasteurisation of acid and acidified foods (2, 3%); Retort pouches and flexible containers (2, 3%); Retort types: still, rotary, hydrostatic and continuous (2, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Process calculation: the general method (3 hard of 5), Aseptic processing and packaging (2 hard of 5), Process calculation: Ball's formula method (1 hard of 3).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Pasteurisation of acid and acidified foods (1 easy of 2); Retort pouches and flexible containers (1 easy of 2).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE XL Thermal Processing & Canning Technology

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.