LAISHA
Open Laisha

GATE XL Transport Phenomena in Food Processing: Fluid Flow, Heat & Mass Transfer: practice questions

GATE — Life Sciences (XL), Section U Food Technology · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
98written to this exam in this subject
15syllabus units

About GATE XL

GATE — Life Sciences (XL), Section U Food Technology is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks. MCQ, MSQ and NAT. Within XL, Section P Chemistry is understood to be compulsory and the candidate chooses two further sections, of which U Food Technology is one; this structure and the mark split are from earlier brochures and were not re-read for 2026.

Source: gate2026.iitg.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Transport Phenomena in Food Processing: Fluid Flow, Heat & Mass Transfer in GATE XL

Same Section 4 syllabus as XE-G; life-science candidates should practise the core balances, pipe-flow and heat-exchanger calculations, which are less familiar to them than the chemistry and microbiology sections.

Mass and energy balances and the three transfer processes — momentum, heat and mass — applied to foods: pumping viscous products, heating cans and pouches, and moisture and gas movement through foods and packaging films.

Our 98 GATE XL questions in this subject: 28 easy, 43 medium, 27 hard, across 15 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE XL and are not shown on any other exam's page.

Question 1 · hard

A Pitot tube in water (ρ = 1,000 kg/m³) shows a difference of 800 Pa between stagnation and static pressure. The local velocity is closest to

  1. 1.60 m/s
  2. 0.89 m/s
  3. 1.26 m/s
  4. 40.0 m/s
Answer and working

C. 1.26 m/s

v = √(2ΔP/ρ) = √(1.6) = 1.26 m/s. 1.60 m/s omits the square root; 0.89 m/s omits the factor 2; 40.0 m/s takes √(1,600).

Question 2 · medium

In a Venturi meter, the measured pressure difference is proportional to

  1. the flow rate
  2. the square of the flow rate
  3. the square root of the flow rate
  4. the cube of the flow rate
Answer and working

B. the square of the flow rate

From Bernoulli and continuity, ΔP ∝ v² ∝ Q², so Q ∝ √ΔP.

Question 3 · medium

In laminar flow in a pipe, the Fanning friction factor equals

  1. 16/Re
  2. 64/Re
  3. 0.0791 Re^−0.25
  4. 0.316 Re^−0.25
Answer and working

A. 16/Re

Fanning f = 16/Re; Darcy fD = 64/Re = 4f. 0.0791 Re^−0.25 is the Fanning Blasius equation for turbulent flow; 0.316 Re^−0.25 is its Darcy form.

Question 4 · easy

A pump moves 2 kg/s of juice, supplying 300 J/kg of energy to the fluid at 60 % efficiency. The shaft power is

  1. 360 W
  2. 1,000 W
  3. 600 W
  4. 500 W
Answer and working

B. 1,000 W

Shaft power = ṁEp/η = 2 × 300/0.6 = 1,000 W. 600 W is the fluid power; 360 W multiplies by 0.6; 500 W divides 300 by 0.6 only.

Question 5 · hard

For insulation with k = 0.04 W/m K on a cylinder with outside film coefficient 10 W/m² K, the critical radius of insulation is

  1. 8 mm
  2. 0.4 mm
  3. 4 mm
  4. 250 mm
Answer and working

C. 4 mm

r_c = k/h = 0.04/10 = 0.004 m = 4 mm. 8 mm is the sphere value 2k/h; 0.4 mm and 250 mm are unit or inversion slips (h/k = 250 m⁻¹).

Question 6 · hard

Milk with Re = 29,000 and Pr = 13 is heated in a 38 mm tube (k = 0.55 W/m K). Using Dittus–Boelter for heating, Nu = 0.023 Re^0.8 Pr^0.4, the film coefficient is closest to

  1. 2,669 W/m² K
  2. 3,450 W/m² K
  3. 238 W/m² K
  4. 16.5 W/m² K
Answer and working

B. 3,450 W/m² K

Nu = 0.023 × 29,000^0.8 × 13^0.4 = 238; h = Nu k/D = 238 × 0.55/0.038 = 3,450 W/m² K. The 0.3 exponent is for cooling; 238 is Nu itself; 16.5 inverts k/D.

Question 7 · medium

Foods heat and cool slowly mainly because their thermal diffusivity is

  1. low, about 1.2–1.6 × 10⁻⁷ m²/s
  2. high, about 1 × 10⁻³ m²/s
  3. equal to that of copper
  4. zero
Answer and working

A. low, about 1.2–1.6 × 10⁻⁷ m²/s

Foods, like water, have low k/ρcp, so heat penetrates slowly into large pieces.

Question 8 · hard

In an exchanger, Cmin = 3,900 W/K, hot inlet 90 °C and cold inlet 10 °C, effectiveness 0.80. The heat transferred is closest to

  1. 312,000 kW
  2. 390 kW
  3. 200 kW
  4. 250 kW
Answer and working

D. 250 kW

Qmax = Cmin(Th,in − Tc,in) = 3,900 × 80 = 312 kW; Q = 0.80 × 312 = 250 kW. 312,000 kW is Qmax with a unit slip; 390 kW divides by 0.80; 200 kW applies the effectiveness twice.

Question 9 · easy

The dimensions of dynamic viscosity in the M-L-T system are:

  1. M L T⁻²
  2. M L² T⁻¹
  3. L² T⁻¹
  4. M L⁻¹ T⁻¹
Answer and working

D. M L⁻¹ T⁻¹

Viscosity is shear stress divided by shear rate: (M L⁻¹ T⁻²)/(T⁻¹) = M L⁻¹ T⁻¹, which is Pa·s. M L T⁻² is force. M L² T⁻¹ is angular momentum. L² T⁻¹ is kinematic viscosity, viscosity divided by density.

Question 10 · medium

A loaf surface (0.1 m², emissivity 0.9, 300 K) is surrounded by oven walls at 500 K. With σ = 5.67 × 10⁻⁸ W/(m²·K⁴), the net radiant heat gain is closest to:

  1. 308 W
  2. 278 W
  3. 8 W
  4. 319 W
Answer and working

B. 278 W

q = εσA(Tw⁴ − Ts⁴) = 0.9 × 5.67 × 10⁻⁸ × 0.1 × (6.25 × 10¹⁰ − 8.1 × 10⁹) = 278 W. 308 W takes ε = 1. 8 W raises the temperature difference (200 K) to the fourth power instead of subtracting fourth powers. 319 W ignores emission from the loaf.

A study plan for Transport Phenomena in Food Processing: Fluid Flow, Heat & Mass Transfer in GATE XL

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (42% of the 98 questions): Flow in pipes: Reynolds number, friction factor and pressure drop for Newtonian fluids (9, 9%); Heat exchangers: plate, tubular and scraped-surface; LMTD and effectiveness (9, 9%); Units, dimensions and dimensional analysis (8, 8%); Unsteady-state heat transfer: lumped systems and Heisler charts (8, 8%); Energy balances and steam tables (7, 7%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Material balances on mixing, concentration and drying (7, 7%); Steady-state conduction through slabs, cylinders and composite walls (7, 7%); Convection: film coefficients and dimensionless numbers (6, 6%); Convective mass transfer (6, 6%); Pumps for foods: centrifugal and positive-displacement (6, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Radiation heat transfer (6, 6%); Fluid statics and the Bernoulli equation (5, 5%); Molecular diffusion and Fick's law (5, 5%); Permeability through single and multilayer films (5, 5%); Flow of non-Newtonian foods in pipes (4, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Heat exchangers: plate, tubular and scraped-surface; LMTD and effectiveness (4 hard of 9), Molecular diffusion and Fick's law (2 hard of 5), Permeability through single and multilayer films (2 hard of 5).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Material balances on mixing, concentration and drying (4 easy of 7); Units, dimensions and dimensional analysis (4 easy of 8).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE XL Transport Phenomena in Food Processing: Fluid Flow, Heat & Mass Transfer

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.