GATE — Engineering Sciences (XE), Section G Food Technology · India · IITs and IISc on rotation (2027: IIT Madras)
Original practice questions written to the published syllabus · not past papersGATE — Engineering Sciences (XE), Section G Food Technology is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks. MCQ, MSQ and NAT. General Aptitude is common to every GATE paper; within XE, Section A Engineering Mathematics is compulsory (stated on the 2026 XE-A syllabus) and the candidate chooses two further sections, of which G Food Technology is one. The split of marks between GA, XE-A and the two chosen sections is from Laisha's knowledge of earlier brochures and was not re-read for 2026.
Source: gate2026.iitg.ac.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Section 4 names mass and energy balance; momentum transfer (flow rate and pressure drop relationships for Newtonian fluids in pipes, Reynolds number); heat transfer by conduction, convection and radiation and heat exchangers; and mass transfer (Fick's law, convective mass transfer, permeability through single and multilayer films). Expect numerical-answer questions on Reynolds number, Hagen–Poiseuille and Fanning pressure drop, composite-wall conduction, LMTD, Dittus–Boelter, Biot and lumped cooling, and film permeation; units and the Fanning/Darcy distinction are the common traps.
Mass and energy balances and the three transfer processes — momentum, heat and mass — applied to foods: pumping viscous products, heating cans and pouches, and moisture and gas movement through foods and packaging films.
Our 88 GATE XE questions in this subject: 25 easy, 38 medium, 25 hard, across 15 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to GATE XE and are not shown on any other exam's page.
5,000 kg/h of milk at 12 % total solids is concentrated to 45 % total solids. The water evaporated is closest to
D. 3,667 kg/h
W = F(1 − xF/xP) = 5,000 × (1 − 12/45) = 3,667 kg/h. 1,333 kg/h is the concentrate; 1,650 kg/h multiplies by 0.33 (45 − 12 as a fraction); 3,350 kg/h subtracts percentages (5,000 × 0.67).
Steam is the preferred heating medium in food plants mainly because it
B. releases a large latent heat at a constant, pressure-controlled temperature
Condensing steam delivers about 2,200 kJ/kg at a temperature fixed by its pressure, with very high film coefficients; condensate must be removed by traps.
The Bernoulli equation for an ideal fluid states that along a streamline the sum of
B. pressure, kinetic and potential energy per unit mass is constant
P/ρ + v²/2 + gz = constant for frictionless, incompressible, steady flow; real flows add pump work and friction terms.
Milk (ρ = 1,030 kg/m³, μ = 2.0 mPa s) flows at 1.5 m/s in a 38 mm tube. The Reynolds number is closest to
A. 29,355
Re = ρvD/μ = 1,030 × 1.5 × 0.038/0.002 = 29,355, turbulent. 29 and 29,355,000 come from unit slips in μ (Pa s vs mPa s); 2,936 uses D = 3.8 mm.
Cavitation in a pump is avoided when
B. net positive suction head available exceeds that required
NPSHa must exceed NPSHr so that inlet pressure stays above vapour pressure; hot liquids and restrictive suction lines reduce NPSHa.
In a heat exchanger with a thin stainless-steel wall, the wall usually contributes little to the overall resistance because
A. metal conductivity is high compared with the fluid films
A 1–2 mm steel wall has resistance far below the convective films and fouling layers.
Natural (free) convection is driven by
C. density differences caused by temperature differences
Warm fluid is less dense and rises; forced convection uses pumps or fans. The Grashof number characterises it.
A food slab (k = 0.5 W/m K, ρ = 1,000 kg/m³, cp = 3,600 J/kg K) of half-thickness 20 mm is heated for 30 min. The Fourier number is about
C. 0.62
α = k/ρcp = 1.39e-07 m²/s; Fo = αt/L² = 1.39e-07 × 1,800/0.02² = 0.62. 0.156 uses the full thickness 40 mm; 0.01042 uses 30 s; 2.5 uses 10 mm.
A counter-current heat exchanger has equal heat capacity rates (Cr = 1) and NTU = 2.0. Its effectiveness is
B. 0.667
For Cr = 1, ε = NTU/(1 + NTU) = 2/3 = 0.667. 0.865 is 1 − e^−2, valid only when Cr = 0; 0.500 is the co-current limit; 1.000 would need infinite NTU.
Water evaporates from a 0.5 m² wet surface with km = 0.02 m/s; vapour concentrations are 0.017 kg/m³ at the surface and 0.008 kg/m³ in the air. The evaporation rate is
D. 0.09 g/s
N = kmA(Cs − C∞) = 0.02 × 0.5 × 0.009 = 9.00e-05 kg/s = 0.09 g/s. 0.17 g/s uses Cs only; 0.08 g/s uses C∞ only; 9.0 g/s is a unit slip.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.