LAISHA
Open Laisha

GATE XE Mechanical Unit Operations: Size Reduction, Mixing & Separation: practice questions

GATE — Engineering Sciences (XE), Section G Food Technology · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
83written to this exam in this subject
15syllabus units

About GATE XE

GATE — Engineering Sciences (XE), Section G Food Technology is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks. MCQ, MSQ and NAT. General Aptitude is common to every GATE paper; within XE, Section A Engineering Mathematics is compulsory (stated on the 2026 XE-A syllabus) and the candidate chooses two further sections, of which G Food Technology is one. The split of marks between GA, XE-A and the two chosen sections is from Laisha's knowledge of earlier brochures and was not re-read for 2026.

Source: gate2026.iitg.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Mechanical Unit Operations: Size Reduction, Mixing & Separation in GATE XE

Section 4 names size reduction of solids, high-pressure homogenisation, filtration, centrifugation, settling, sieving, and mixing and agitation of liquids. Expect numerical-answer questions on Rittinger, Kick and Bond energies, Stokes settling and centrifugal settling velocities, g-number, constant-pressure filtration time, membrane flux, rejection and concentration factor, screen effectiveness and agitator power from the power number, with equipment-selection reasoning.

The mechanical operations that clean, sort, reduce, mix, homogenise and separate food materials, including filtration, centrifugation and membrane processes, with the design equations used to size them.

Our 83 GATE XE questions in this subject: 17 easy, 47 medium, 19 hard, across 15 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE XE and are not shown on any other exam's page.

Question 1 · easy

Aspiration (winnowing) separates chaff and dust from grain mainly by differences in

  1. terminal velocity in an air stream
  2. colour detected by photocells
  3. magnetic susceptibility of the particles
  4. electrical conductivity in water
Answer and working

A. terminal velocity in an air stream

Light chaff has a lower terminal velocity and is carried away by air while grain falls. Colour sorters and magnets use other properties.

Question 2 · easy

Sorting differs from grading in that sorting

  1. judges overall quality against an official grade standard
  2. is always done by trained human inspectors at a belt
  3. applies only to processed foods after packing
  4. separates by one measurable property
Answer and working

D. separates by one measurable property

Sorting uses a single property such as size, weight or colour; grading assesses several quality attributes together against standards.

Question 3 · medium

In the turbulent regime in a baffled tank, doubling impeller speed increases power by a factor of

  1. 2
  2. 4
  3. 32
  4. 8
Answer and working

D. 8

P ∝ N³ when Np is constant; 32 is the factor for doubling diameter (D⁵).

Question 4 · easy

By Stokes' law, the settling velocity of a small particle is proportional to

  1. its diameter
  2. the square of its diameter
  3. the square root of its diameter
  4. the cube of its diameter
Answer and working

B. the square of its diameter

v = d²Δρg/18μ, so velocity varies with the square of diameter; doubling d gives four times the settling velocity.

Question 5 · medium

The capacity of a gravity settling tank to remove particles of a given size depends mainly on its

  1. depth
  2. colour
  3. wall thickness
  4. surface area
Answer and working

D. surface area

A particle is removed if its settling velocity exceeds flow/surface area (overflow rate), so area, not depth, governs capacity.

Question 6 · medium

In constant-pressure filtration with negligible medium resistance, collecting 1 m³ of filtrate takes 10 min. Collecting 2 m³ takes

  1. 40 min
  2. 20 min
  3. 14 min
  4. 80 min
Answer and working

A. 40 min

t ∝ V², so t = 10 × 2² = 40 min. 20 min assumes t ∝ V; 14 min uses √2; 80 min uses V³.

Question 7 · hard

Reverse osmosis cannot concentrate fruit juice much beyond about 25–30 % solids mainly because

  1. RO membranes start to pass sugars freely once the juice exceeds 20 % solids
  2. RO heats the juice and caramelises sugars
  3. juice proteins block all membranes immediately
  4. osmotic pressure rises with concentration and opposes the applied pressure
Answer and working

D. osmotic pressure rises with concentration and opposes the applied pressure

π = icRT grows with solute concentration, so very high pressures would be needed; RO is used to pre-concentrate.

Question 8 · medium

Making the particles extremely fine in a percolation extractor can reduce performance because

  1. fine particles contain no soluble material
  2. very fine particles impede drainage of solvent through the bed
  3. fine particles raise the boiling point of the solvent so that it cannot be recovered
  4. fine particles cannot be wetted by any solvent
Answer and working

B. very fine particles impede drainage of solvent through the bed

Short diffusion paths help, but fines pack tightly and block solvent flow.

Question 9 · medium

High supersaturation during crystallisation tends to produce

  1. few large crystals
  2. no crystals
  3. only amorphous glass
  4. many small crystals
Answer and working

D. many small crystals

High supersaturation favours nucleation over growth.

Question 10 · medium

A screw conveyor has D = 0.2 m, shaft d = 0.05 m, pitch 0.2 m, speed 60 rpm and loading 0.4. Its volumetric capacity is closest to

  1. 9.0 m³/h
  2. 509 m³/h
  3. 21.2 m³/h
  4. 8.5 m³/h
Answer and working

D. 8.5 m³/h

Q = (π/4)(0.04 − 0.0025) × 0.2 × 1 rev/s × 0.4 = 0.00236 m³/s = 8.5 m³/h. Ignoring the shaft gives 9.0; using 60 rev/s gives the large value; omitting loading gives 21.2.

A study plan for Mechanical Unit Operations: Size Reduction, Mixing & Separation in GATE XE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (42% of the 83 questions): Membrane processes: microfiltration, ultrafiltration, nanofiltration and reverse osmosis (8, 10%); Size reduction: energy laws of Rittinger, Kick and Bond (8, 10%); Filtration: cake filtration theory and filter aids (7, 8%); Centrifugation and centrifugal separators (6, 7%); Expression and solid-liquid extraction (6, 7%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Mixing of solids, pastes and liquids; agitation and power number (6, 7%); Sieving and particle-size analysis (6, 7%); Cleaning, sorting and grading of raw materials (5, 6%); Crystallisation (5, 6%); Distillation and supercritical fluid extraction (5, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: High-pressure homogenisation (5, 6%); Settling and sedimentation (5, 6%); Peeling methods (4, 5%); Size-reduction equipment for dry and wet foods (4, 5%); Material handling: conveyors and elevators for foods (3, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Centrifugation and centrifugal separators (3 hard of 6), Membrane processes: microfiltration, ultrafiltration, nanofiltration and reverse osmosis (3 hard of 8), Mixing of solids, pastes and liquids; agitation and power number (2 hard of 6).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Cleaning, sorting and grading of raw materials (2 easy of 5); Material handling: conveyors and elevators for foods (1 easy of 3).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE XE Mechanical Unit Operations: Size Reduction, Mixing & Separation

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.