LAISHA
Open Laisha

GATE XE Fats & Oils Technology: practice questions

GATE — Engineering Sciences (XE), Section G Food Technology · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
34written to this exam in this subject
13syllabus units

About GATE XE

GATE — Engineering Sciences (XE), Section G Food Technology is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks. MCQ, MSQ and NAT. General Aptitude is common to every GATE paper; within XE, Section A Engineering Mathematics is compulsory (stated on the 2026 XE-A syllabus) and the candidate chooses two further sections, of which G Food Technology is one. The split of marks between GA, XE-A and the two chosen sections is from Laisha's knowledge of earlier brochures and was not re-read for 2026.

Source: gate2026.iitg.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Fats & Oils Technology in GATE XE

Section 3 names oil processing: expelling, solvent extraction, refining and hydrogenation. Expect MCQs on refining steps and their purposes, hydrogenation and trans formation, and NATs on oil recovery from mass balance, NaOH for neutralisation, FFA from acid value and mean molecular weight from saponification value.

From oilseed to finished fat: mechanical expression and solvent extraction, refining, bleaching and deodorisation, fat modification by hydrogenation, interesterification and fractionation, and the fat products — margarine, shortening, vanaspati and specialty fats — made from them.

Our 34 GATE XE questions in this subject: 17 easy, 12 medium, 5 hard, across 13 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE XE and are not shown on any other exam's page.

Question 1 · easy

In alkali refining, free fatty acids are removed as:

  1. Lecithin
  2. Soapstock
  3. Stearin
  4. Distillate
Answer and working

B. Soapstock

Sodium hydroxide converts them to soaps.

Question 2 · medium

During hydrogenation, the iodine value of the oil:

  1. Doubles
  2. Stays constant
  3. Falls
  4. Rises
Answer and working

C. Falls

Double bonds are saturated.

Question 3 · easy

In fractionation, the solid fraction is called:

  1. Olein
  2. Soapstock
  3. Miscella
  4. Stearin
Answer and working

D. Stearin

The liquid fraction is olein.

Question 4 · medium

An oil has an acid value of 2.0. What is its FFA content as oleic acid?

  1. 4.0%
  2. 2.0%
  3. 1.0%
  4. 0.5%
Answer and working

C. 1.0%

FFA = acid value / 1.99 = 2.0/1.99 = 1.0%.

Question 5 · hard

An oil has a saponification value of 190. What is its approximate mean triacylglycerol molecular weight?

  1. 190
  2. 886
  3. 1,770
  4. 295
Answer and working

B. 886

3 × 56,100/190 = 886. 295 omits the factor of 3.

Question 6 · easy

In a continuous deodoriser, the hot deodorised oil leaving the column is passed through an oil-to-oil heat exchanger mainly to:

  1. Add steam to the outgoing oil
  2. Bleach the oil a second time
  3. Remove waxes before storage
  4. Preheat incoming oil and save energy
Answer and working

D. Preheat incoming oil and save energy

Oil leaves the deodoriser at roughly 230 to 260 °C and must be cooled before storage, while incoming oil must be heated to that range. Exchanging heat between the two streams recovers a large share of the energy and cuts fuel or thermal fluid demand. The exchanger adds no steam, has no adsorbent for bleaching, and dewaxing needs slow chilling and filtration, not a heat recovery stage.

Question 7 · medium

Studies of deep-fat frying of potato show that most of the oil in the finished product is taken up:

  1. After removal from the fryer, as the food cools
  2. In the first seconds, before any water evaporates
  3. Only when the oil is above its smoke point
  4. Evenly throughout the frying period
Answer and working

A. After removal from the fryer, as the food cools

While frying, escaping steam keeps the pores pressurised and largely blocks oil entry. When the piece is lifted out and cools, vapour condenses, the pressure in the pores falls, and surface oil is drawn into the crust. Hence draining time and de-oiling matter. Oil does not enter mainly before evaporation starts, smoke point is unrelated to uptake, and uptake is not uniform over time.

Question 8 · hard

A physical blend of fully hydrogenated soybean oil and liquid soybean oil is chemically interesterified. Compared with the blend before reaction, the product has:

  1. A higher melting point and more trisaturated TAG
  2. A higher iodine value and some trans fatty acids
  3. A lower melting point and less trisaturated TAG
  4. An unchanged melting point and solid fat content
Answer and working

C. A lower melting point and less trisaturated TAG

The blend contains high-melting trisaturated TAG from the hard stock and triunsaturated TAG from the oil. Random interesterification redistributes fatty acids into mixed SSU and SUU species, so the trisaturated fraction falls and the melting point and waxy solids at body temperature drop. Fatty acid composition is unchanged, so iodine value stays the same and no trans acids form; the melting behaviour clearly does change.

Question 9 · easy

The shorthand C18:3 n-3 denotes:

  1. α-Linolenic acid
  2. Linoleic acid
  3. γ-Linolenic acid
  4. Stearic acid
Answer and working

A. α-Linolenic acid

C18:3 means 18 carbons with three double bonds, and n-3 places the first double bond three carbons from the methyl end, which is α-linolenic acid found in linseed, canola and soybean oils. Linoleic acid is C18:2 n-6. γ-Linolenic acid is also C18:3 but belongs to the n-6 family, as in evening primrose oil. Stearic acid is C18:0, fully saturated.

Question 10 · hard

A margarine based only on hydrogenated soybean and canola oils turns grainy in storage. Adding which fat is the usual remedy?

  1. Hydrogenated sunflower oil
  2. Palm or cottonseed oil
  3. More hydrogenated canola oil
  4. Unhydrogenated linseed oil
Answer and working

B. Palm or cottonseed oil

Hydrogenated soybean, canola and sunflower fats, with fairly uniform C18 chains, tend to convert to large β crystals that feel sandy. Palm and cottonseed oils carry more palmitic acid, giving mixed chain lengths that stabilise the fine β′ form. Adding sunflower or more canola keeps the same β-tending pattern. Linseed oil is liquid and highly unsaturated, so it softens the product without stabilising β′.

A study plan for Fats & Oils Technology in GATE XE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (50% of the 34 questions): Neutralisation, bleaching and deodorisation; physical refining (4, 12%); Oil quality tests: acid value, peroxide value, iodine value and saponification value (4, 12%); Fractionation (3, 9%); Hydrogenation and trans fatty acids (3, 9%); Interesterification: chemical and enzymatic (3, 9%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Margarine, shortening and vanaspati (3, 9%); Mechanical expression and expellers (3, 9%); Solvent extraction and desolventising (3, 9%); Sources and composition of edible oils and fats (3, 9%); Frying oil deterioration and management (2, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: By-products of oil refining (1, 3%); Degumming and lecithin recovery (1, 3%); Specialty fats and cocoa butter equivalents (1, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Hydrogenation and trans fatty acids (1 hard of 3), Interesterification: chemical and enzymatic (1 hard of 3), Margarine, shortening and vanaspati (1 hard of 3).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: By-products of oil refining (1 easy of 1); Degumming and lecithin recovery (1 easy of 1).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE XE Fats & Oils Technology

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.