LAISHA
Open Laisha

GATE XE Food Packaging Science & Technology: practice questions

GATE — Engineering Sciences (XE), Section G Food Technology · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
43written to this exam in this subject
14syllabus units

About GATE XE

GATE — Engineering Sciences (XE), Section G Food Technology is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks. MCQ, MSQ and NAT. General Aptitude is common to every GATE paper; within XE, Section A Engineering Mathematics is compulsory (stated on the 2026 XE-A syllabus) and the candidate chooses two further sections, of which G Food Technology is one. The split of marks between GA, XE-A and the two chosen sections is from Laisha's knowledge of earlier brochures and was not re-read for 2026.

Source: gate2026.iitg.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Food Packaging Science & Technology in GATE XE

Section 3 names packaging materials, aseptic packaging, and controlled and modified atmosphere storage; Section 4 names permeability through single and multilayer films. Expect questions on polymer barrier properties, laminate structures, MAP gas roles, aseptic package sterilisation, and numericals on film permeation, WVTR from cup tests and series barrier layers.

Packaging as part of the preservation system: materials and their barrier properties, package design and testing, metal cans, glass, paper and plastics, aseptic, modified-atmosphere, active and intelligent packaging, migration and food-contact law, and packaging sustainability. Agricultural Engineering's storage-engineering-packaging covers bulk storage and an introduction to packaging materials; this subject is the full packaging course.

Our 43 GATE XE questions in this subject: 17 easy, 16 medium, 10 hard, across 14 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE XE and are not shown on any other exam's page.

Question 1 · easy

Food glass containers are mainly made of

  1. borosilicate laboratory glass
  2. lead crystal glass
  3. fused quartz
  4. soda-lime-silica glass
Answer and working

D. soda-lime-silica glass

Soda-lime-silica is cheap and suitable; borosilicate is used for laboratory and ovenware.

Question 2 · easy

WVTR and OTR values must be reported with

  1. the price of the film
  2. the colour of the film
  3. the protein content of the food to be packed in it
  4. the test temperature and humidity
Answer and working

D. the test temperature and humidity

Transmission rises with temperature and, for hydrophilic films, with humidity; values are meaningless without conditions.

Question 3 · medium

In aseptic packaging, the filling zone is kept sterile mainly by

  1. ultraviolet lamps alone
  2. opening the machine for manual cleaning every hour of production
  3. cooling the zone to 0 °C
  4. positive pressure of HEPA-filtered sterile air
Answer and working

D. positive pressure of HEPA-filtered sterile air

Overpressure filtered air excludes contamination; surfaces are sterilised before production.

Question 4 · easy

In modified-atmosphere packaging, carbon dioxide mainly

  1. provides oxygen for the respiration of the packed product
  2. colours meat bright red
  3. acts as an inert filler only
  4. inhibits aerobic spoilage bacteria and moulds
Answer and working

D. inhibits aerobic spoilage bacteria and moulds

CO2 inhibits Gram-negative aerobes such as Pseudomonas and moulds; N2 is the filler; O2 gives meat bloom.

Question 5 · hard

Equilibrium MAP for fresh-cut produce relies on

  1. complete removal of all oxygen with iron scavengers
  2. film permeability matched to produce respiration
  3. pure carbon dioxide in the pack
  4. an impermeable glass container
Answer and working

B. film permeability matched to produce respiration

Transmission balances respiration at low O2, raised CO2, avoiding anaerobic fermentation.

Question 6 · easy

Wax coatings on apples and citrus are an example of

  1. active oxygen scavenging
  2. intelligent packaging
  3. edible coating
  4. aseptic packaging
Answer and working

C. edible coating

Waxes reduce moisture loss and add gloss.

Question 7 · medium

A film has an OTR of 10 cm³/m² day measured at 1 atm oxygen partial pressure difference. A pack with 0.05 m² of this film sits in air (0.21 atm O₂) with essentially no oxygen inside. The daily oxygen ingress is about

  1. 0.105 cm³/day
  2. 0.5 cm³/day
  3. 2.1 cm³/day
  4. 0.0105 cm³/day
Answer and working

A. 0.105 cm³/day

Permeation scales with area and with the partial pressure difference, so ingress = 10 × 0.05 × 0.21 = 0.105 cm³ per day. 0.5 cm³/day forgets that air contains only 21% oxygen, while the test used pure oxygen. 2.1 cm³/day multiplies OTR by 0.21 but ignores the small area. 0.0105 cm³/day slips a decimal place.

Question 8 · hard

In a sealed LDPE bag of respiring fresh produce with a respiratory quotient near 1, the steady-state oxygen fall below 21% is usually much larger than the CO₂ rise above 0%. This is because

  1. The produce absorbs CO₂ into its tissues permanently
  2. The film is several times more permeable to CO₂ than to O₂
  3. Respiration consumes O₂ without producing CO₂
  4. Nitrogen in the pack reacts with the CO₂
Answer and working

B. The film is several times more permeable to CO₂ than to O₂

At steady state, gas leaving or entering through the film equals respiratory exchange. With RQ near 1 the produce makes roughly as much CO₂ as it uses O₂, but polyolefins pass CO₂ about three to six times faster than O₂, so CO₂ escapes with a small build-up while O₂ must fall further to drive enough inflow. Tissue absorption is minor and not permanent. Nitrogen is inert.

Question 9 · easy

LDPE has a density of 0.92 g/cm³. The mass of 1 m² of 50 µm LDPE film is

  1. 4.6 g
  2. 54 g
  3. 460 g
  4. 46 g
Answer and working

D. 46 g

Volume of 1 m² at 50 µm is 1 m² × 50 × 10⁻⁶ m = 5 × 10⁻⁵ m³, which is 50 cm³. Mass = 50 × 0.92 = 46 g, so the film's grammage is 46 g/m². 54 g divides thickness by density instead of multiplying. 4.6 g and 460 g misplace the decimal by a factor of ten. Film grammage is used to estimate material costs and pack weights.

Question 10 · hard

A Gelbo flex test is run on a foil laminate before it is approved for a pouch that will be shipped long distances. The test checks

  1. Tear resistance at a notch
  2. Pinhole formation and barrier loss on repeated flexing
  3. Heat-seal strength at high temperature
  4. Coefficient of friction between film surfaces
Answer and working

B. Pinhole formation and barrier loss on repeated flexing

The Gelbo tester twists and crushes film repeatedly, simulating handling and transport, after which pinholes are counted or oxygen and water vapour transmission are remeasured. Aluminium foil and metallised layers are especially prone to flex cracking. Tear resistance is measured by the Elmendorf test, seal strength by peel or hot-tack tests, and slip by coefficient of friction testing.

A study plan for Food Packaging Science & Technology in GATE XE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (58% of the 43 questions): Barrier properties: water vapour and oxygen transmission rates (7, 16%); Metal cans: tinplate, tin-free steel and aluminium; corrosion and lacquers (5, 12%); Modified-atmosphere and vacuum packaging (5, 12%); Laminates, coextrusion and coatings (4, 9%); Plastics: polymer types, properties and processing (4, 9%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Active packaging: oxygen scavengers, moisture absorbers and antimicrobials (3, 7%); Edible and biodegradable packaging (3, 7%); Paper, paperboard and corrugated packaging (3, 7%); Aseptic packaging systems (2, 5%); Functions and levels of food packaging (2, 5%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Migration and food-contact material regulation (2, 5%); Glass containers (1, 2%); Intelligent packaging: indicators, sensors and RFID (1, 2%); Package testing methods (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Intelligent packaging: indicators, sensors and RFID (1 hard of 1), Package testing methods (1 hard of 1), Modified-atmosphere and vacuum packaging (3 hard of 5).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Functions and levels of food packaging (2 easy of 2); Glass containers (1 easy of 1).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE XE Food Packaging Science & Technology

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.