LAISHA
Open Laisha

ICAR AIEEA-PG / PGS Extrusion & Texturisation Technology: practice questions

ICAR AIEEA-PG / PGS — Code 18 Food Science Technology · India · ICAR through the National Testing Agency

Original practice questions written to the published syllabus · not past papers
10worked here, free
50written to this exam in this subject
11syllabus units

About ICAR AIEEA-PG / PGS

ICAR AIEEA-PG / PGS — Code 18 Food Science Technology is a postgraduate admission exam run by ICAR through the National Testing Agency, for candidates in India. Computer-based, multiple choice, +4/−1 marking.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Extrusion & Texturisation Technology in ICAR AIEEA-PG / PGS

Unit II names extrusion among unit operations. MCQs test extruder types and zones, die functions, HTST cooking, products (snacks, pasta, TVP) and quality indices.

The extruder as a continuous cooker and shaper: single- and twin-screw extruders, the transformations of starch and protein inside them, expanded snacks, breakfast cereals, pasta, and high-moisture extrusion for meat analogues.

Our 50 ICAR AIEEA-PG / PGS questions in this subject: 25 easy, 22 medium, 3 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG / PGS and are not shown on any other exam's page.

Question 1 · easy

Extrusion cooking is best described as a

  1. low-temperature long-time process
  2. freezing process
  3. fermentation process
  4. high-temperature short-time process
Answer and working

D. high-temperature short-time process

Temperatures of roughly 100–180 °C for tens of seconds cook and shape the food.

Question 2 · medium

In many cooking extruders, most of the heat comes from

  1. electric heaters mounted inside the hollow screw shaft
  2. microwave sources in the barrel
  3. viscous dissipation of mechanical energy
  4. radiation from the die
Answer and working

C. viscous dissipation of mechanical energy

Friction and shear in the viscous melt convert motor energy into heat; barrel heating supplements it.

Question 3 · medium

Forming (cold) extrusion differs from cooking extrusion in that it

  1. always operates above 150 °C
  2. produces only expanded snacks with very high porosity
  3. shapes without significant cooking or expansion
  4. needs no die
Answer and working

C. shapes without significant cooking or expansion

Pasta, doughs, liquorice and pellets are shaped below about 50–60 °C.

Question 4 · medium

Bronze pasta dies, compared with PTFE dies, give pasta that is

  1. rougher and holds sauce better
  2. smoother and glossier
  3. softer after cooking
  4. whiter in colour
Answer and working

A. rougher and holds sauce better

Bronze gives a matt, porous surface; PTFE gives smooth, yellower, glossier pasta.

Question 5 · easy

At the low moisture of extrusion, starch granules are transformed mainly by

  1. swelling of granules in excess water, as in a sauce
  2. fermentation by yeasts
  3. freezing and thawing
  4. shear and heat disrupting and melting them
Answer and working

D. shear and heat disrupting and melting them

There is too little water for full swelling; mechanical and thermal energy melt and disperse starch.

Question 6 · medium

Fibrous structure in extruded plant proteins is fixed mainly by

  1. ionising radiation
  2. adding meat fibres
  3. disulphide and non-covalent bonds after alignment
  4. freezing the extrudate rapidly in liquid nitrogen after cutting
Answer and working

C. disulphide and non-covalent bonds after alignment

Unfolded proteins align in flow and bond as they cool.

Question 7 · easy

Rehydrated TVP typically absorbs water equal to about

  1. one-tenth of its weight
  2. ten times its weight
  3. two to three times its weight
  4. none of its weight
Answer and working

C. two to three times its weight

Porous TVP takes up two to three times its dry mass of water.

Question 8 · medium

Bowl life of a breakfast cereal is

  1. its shelf life in the box
  2. its sugar content
  3. its cooking time
  4. the time it stays crisp in milk
Answer and working

D. the time it stays crisp in milk

Density, structure and coating affect how fast milk softens it.

Question 9 · medium

Shredded wheat is made by

  1. shredding cooked whole wheat between grooved rolls
  2. extruding fine wheat flour through a star-shaped die and frying it
  3. gun-puffing whole kernels
  4. flaking pellets
Answer and working

A. shredding cooked whole wheat between grooved rolls

It is a traditional non-extruded process (cereal-science-milling).

Question 10 · easy

30 g of a puffed snack fills a 1.0 L container. Its bulk density is

  1. 30 kg/m³
  2. 0.03 kg/m³
  3. 300 kg/m³
  4. 3,000 kg/m³
Answer and working

A. 30 kg/m³

30 g per litre equals 30 kg/m³ (1 g/L = 1 kg/m³). 300 and 3,000 are factor-of-ten slips; 0.03 converts the wrong way.

A study plan for Extrusion & Texturisation Technology in ICAR AIEEA-PG / PGS

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (50% of the 50 questions): Expanded snacks and ready-to-eat breakfast cereals (7, 14%); Pasta and cold-forming extrusion (6, 12%); Principles of extrusion cooking (6, 12%); Twin-screw extruders: configuration and screw elements (6, 12%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Quality evaluation of extrudates: expansion ratio and bulk density (5, 10%); Starch transformations during extrusion (5, 10%); Die design and product shaping (4, 8%); Specific mechanical energy and process variables (4, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Protein texturisation: low-moisture and high-moisture extrusion (3, 6%); Single-screw extruders: flow and pressure (3, 6%); Co-extrusion and filled products (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Specific mechanical energy and process variables (1 hard of 4), Starch transformations during extrusion (1 hard of 5), Expanded snacks and ready-to-eat breakfast cereals (1 hard of 7).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Co-extrusion and filled products (1 easy of 1); Quality evaluation of extrudates: expansion ratio and bulk density (4 easy of 5).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG / PGS Extrusion & Texturisation Technology

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.