LAISHA
Open Laisha

ICAR AICE-JRF/SRF Food Plant Design, Hygienic Engineering, Utilities & Automation: practice questions

ICAR AICE-JRF/SRF (PhD) — Food Processing Technology, Food Safety & Quality, Processing and Food Engineering · India · ICAR through the National Testing Agency

Original practice questions written to the published syllabus · not past papers
10worked here, free
111written to this exam in this subject
14syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Food Processing Technology, Food Safety & Quality, Processing and Food Engineering is a PhD, fellowship and lectureship exam run by ICAR through the National Testing Agency, for candidates in India. Computer-based, multiple choice.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Food Plant Design, Hygienic Engineering, Utilities & Automation in ICAR AICE-JRF/SRF

Turning a process into a plant that is hygienic, efficient and safe: hygienic equipment and building design, plant layout, process flow and equipment selection, steam, water, compressed air and refrigeration utilities, instrumentation and automation, energy audit and scale-up. Agricultural Engineering's food-quality-safety-plant-design covers plant location, layout and feasibility reports; this subject adds hygienic engineering (EHEDG and 3-A principles), utilities, automation and energy management in depth.

Our 111 ICAR AICE-JRF/SRF questions in this subject: 36 easy, 49 medium, 26 hard, across 14 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · medium

A company comparing two sites finds that one has the higher weighted factor-rating total but no assured supply of potable water. What should it conclude?

  1. Reject that site, because failing an essential factor rules it out whatever its total
  2. Choose that site, because the highest weighted total always identifies the best location
  3. Re-weight water at zero so that the comparison is not distorted by a single factor
  4. Choose that site and plan to use non-potable water for cleaning food-contact surfaces
Answer and working

A. Reject that site, because failing an essential factor rules it out whatever its total

Factor rating supports judgement; a site that fails an essential requirement such as potable water is excluded regardless of its score. Non-potable water cannot be used on food-contact surfaces, and zeroing the weight of the problem factor hides the very risk the method should expose.

Question 2 · medium

What does a process flow diagram normally include that a block flow diagram does not?

  1. Every valve type, line number, insulation detail and instrument tag in the plant
  2. Major equipment symbols, main lines with flow direction, key conditions and a stream table
  3. Only the main process steps drawn as labelled boxes with input and output arrows
  4. The room layout with clearances around machines and the routes for staff movement
Answer and working

B. Major equipment symbols, main lines with flow direction, key conditions and a stream table

A PFD adds standard equipment symbols, main process lines, operating conditions and a stream table of flows and compositions from material and energy balances. Every valve and instrument belongs on the P&ID; boxes and arrows alone are the block diagram; clearances are layout drawings.

Question 3 · easy

A U-shaped material flow is chosen for a new plant. What is its usual advantage?

  1. It gives the longest possible path, which allows extra inspection stations
  2. Raw and finished product cross in the middle, which shortens forklift routes
  3. Receiving and dispatch are on one side and share dock facilities
  4. It removes the need for any separation between raw and finished goods
Answer and working

C. Receiving and dispatch are on one side and share dock facilities

U-shaped flow brings goods in and out on one side, sharing docks and yard space, while product still moves forward. Crossing raw and finished flows is a hygiene fault, path length is not a goal, and separation between raw and finished goods is still required.

Question 4 · easy

Which tool records the desired closeness between each pair of departments as part of layout planning?

  1. A Gantt chart of the project
  2. A relationship (REL) chart
  3. A cause-and-effect (fishbone) diagram
  4. A stream table on the PFD
Answer and working

B. A relationship (REL) chart

The REL chart rates how close each pair of activities should be (absolutely necessary to undesirable) and feeds layout design, alongside from-to charts of material movement. Gantt charts schedule projects; fishbone diagrams analyse causes; stream tables give flows.

Question 5 · hard

After repair welding, a stainless steel tank shows rust spots. What is the usual corrective treatment before returning it to service?

  1. Leave it in service so the product itself forms a protective layer
  2. Paint the welds with a food-grade enamel to seal them from the product
  3. Clean and passivate with nitric or citric acid
  4. Rinse it with hot hypochlorite solution to dissolve the rust spots
Answer and working

C. Clean and passivate with nitric or citric acid

Free iron and heat tint left by welding disrupt the passive film; cleaning and passivating with nitric or citric acid restores it. Paint flakes into product; hot hypochlorite is aggressive and promotes pitting; product does not form a protective film.

Question 6 · medium

Water contains 80 mg/L of calcium and negligible magnesium. What is its hardness expressed as mg/L CaCO3? (Molar masses: Ca 40.08, CaCO3 100.09 g/mol.)

  1. 100 mg/L
  2. 200 mg/L
  3. 80 mg/L
  4. 32 mg/L
Answer and working

B. 200 mg/L

Hardness as CaCO3 = Ca × (100.09 ÷ 40.08) = 80 × 2.497 = 200 mg/L. Leaving it as 80 forgets the conversion; multiplying by the inverse ratio gives 32; halving applies an equivalent-weight step twice. Water near 300 mg/L as CaCO3 is classed as hard.

Question 7 · easy

A reverse-osmosis unit receives 100 m³/h of feed and produces 75 m³/h of permeate. What is its recovery?

  1. 57 %
  2. 25 %
  3. 133 %
  4. 75 %
Answer and working

D. 75 %

Recovery = permeate ÷ feed = 75 ÷ 100 = 75 %; the remaining 25 m³/h is concentrate (reject). 25 % is the reject fraction; 133 % inverts the ratio.

Question 8 · hard

A heater's incoming product temperature is measured and used to adjust steam flow before the outlet temperature changes. What strategy is this?

  1. Integral-only control
  2. Feedforward control
  3. Feedback control
  4. On/off control
Answer and working

B. Feedforward control

Acting on a measured disturbance before it affects the controlled variable is feedforward; it is usually combined with feedback to correct what the model misses. Pure feedback waits for the outlet temperature to deviate.

Question 9 · medium

Which standard structures batch control so that recipes are separated from equipment control?

  1. ISO 14159
  2. ISA-95
  3. ISA-88
  4. ISO 8573-1
Answer and working

C. ISA-88

ISA-88 defines batch control models, separating recipes from equipment logic for flexible, repeatable batches with full records. ISA-95 links plant and enterprise systems, ISO 8573-1 is air purity, ISO 14159 machinery hygiene.

Question 10 · easy

What is the difference between a preliminary and a detailed energy audit?

  1. A preliminary audit is done after a project; a detailed audit is done before it is designed
  2. Preliminary uses bills and a walk-through; detailed measures flows and builds balances
  3. A preliminary audit covers electricity only; a detailed audit covers fuel only
  4. A preliminary audit is done by government inspectors; a detailed audit by operators
Answer and working

B. Preliminary uses bills and a walk-through; detailed measures flows and builds balances

The walk-through audit uses existing data to find obvious savings and decide on further work; the detailed audit measures fuel, electricity, steam, air, refrigeration and water with meters and builds balances for major users. Both may cover all energy forms.

A study plan for Food Plant Design, Hygienic Engineering, Utilities & Automation in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (46% of the 111 questions): Compressed air and refrigeration utilities (11, 10%); Energy audit and energy conservation (11, 10%); Process control: feedback loops, PID and PLC/SCADA (10, 9%); Steam generation and distribution (10, 9%); Materials of construction and corrosion in food plants (9, 8%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Project feasibility and costing of a food plant (9, 8%); Online data acquisition and digital plants (8, 7%); Process flow diagrams and piping and instrumentation diagrams (8, 7%); Instrumentation and sensors in food plants (7, 6%); Plant location and site selection (7, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Water supply and treatment for food plants (7, 6%); Plant layout: product, process and hygienic zoning (6, 5%); Scale-up and pilot plants (6, 5%); Hygienic design of equipment: EHEDG and 3-A principles (2, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Hygienic design of equipment: EHEDG and 3-A principles (1 hard of 2), Scale-up and pilot plants (2 hard of 6), Process control: feedback loops, PID and PLC/SCADA (3 hard of 10).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Plant layout: product, process and hygienic zoning (4 easy of 6); Steam generation and distribution (4 easy of 10).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Food Plant Design, Hygienic Engineering, Utilities & Automation

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.