LAISHA
Open Laisha

Landbased Technician Accreditation Precision Agriculture & System Management: practice questions

Landbased Technician Accreditation (LTA 1–4) · United Kingdom · IAgrE for the AEA industry scheme

Original practice questions written to the published syllabus · not past papers
10worked here, free
24written to this exam in this subject
8syllabus units

About Landbased Technician Accreditation

Landbased Technician Accreditation (LTA 1–4) is a professional certification run by IAgrE for the AEA industry scheme, for candidates in United Kingdom. Four levels from LTA1 Entry to LTA4 Master; LTA2 at advanced apprenticeship level; pathway to EngTech.

Official site: sruc.ac.uk.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Precision Agriculture & System Management in Landbased Technician Accreditation

Practical competence: setting up guidance offsets and look-ahead times, ISOBUS fault finding, yield monitor calibration, and advising customers on system compatibility and data.

Using positioning, sensing and variable-rate control to manage fields by the metre instead of by the hectare.

Our 24 Landbased Technician Accreditation questions in this subject: 8 easy, 14 medium, 2 hard, across 8 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Landbased Technician Accreditation and are not shown on any other exam's page.

Question 1 · hard

A tractor's GNSS antenna is 3.5 m above the ground. On a side slope the tractor rolls 4°. Without terrain compensation the lateral position error at ground level is about

  1. 0.24 m
  2. 3.49 m
  3. 14 m
  4. 0.0085 m
Answer and working

A. 0.24 m

Lateral offset = h × sin θ = 3.5 × sin 4° = 3.5 × 0.0698 = 0.24 m. 3.49 m uses cos θ; 14 m multiplies height by degrees; 0.0085 m is h(1 − cos θ), the vertical drop, not the sideways shift.

Question 2 · easy

Which guidance system turns the steering wheel with an electric motor and can be moved easily between tractors?

  1. Assisted steering system on the wheel or column
  2. Integrated hydraulic auto-steer with valve
  3. Lightbar with operator steering by hand
  4. Foam marker system at each boom end
Answer and working

A. Assisted steering system on the wheel or column

Assisted steering fits a motor to the wheel or column. Integrated auto-steer uses a valve in the steering circuit and a wheel-angle sensor; a lightbar only shows the error; foam markers are not GNSS guidance.

Question 3 · medium

An auto-steer tractor weaves continually from side to side across its line on a smooth field. The most likely setting to change is

  1. Steering aggressiveness, the gain, is too high; reduce it
  2. The correction age is too short; increase it
  3. Antenna height is set too low; set it to zero
  4. Pass-to-pass accuracy is too good; switch to SBAS
Answer and working

A. Steering aggressiveness, the gain, is too high; reduce it

Oscillation about the line is the classic sign of an over-aggressive steering gain; reducing it damps the response. Correction age, zero antenna height and deliberately degrading accuracy do not address a control-loop oscillation.

Question 4 · medium

How is yield usually monitored on a forage harvester, which has no clean-grain elevator?

  1. From an impact plate at the grain elevator head, the same as on grain combines
  2. From the fuel consumption of the engine divided by the working width and the ground speed
  3. From throughput measured at the feed rolls or by crop-flow sensors in the spout
  4. From satellite NDVI the day before cutting, calibrated to a weighed trailer
Answer and working

C. From throughput measured at the feed rolls or by crop-flow sensors in the spout

Forage harvesters estimate throughput from feed-roll displacement or crop-flow sensors, often with on-board near-infrared sensing of dry matter. They have no grain elevator; fuel use and imagery are not the standard yield measurements.

Question 5 · medium

Why must ECa readings from different days be standardised to a reference temperature, usually 25 °C?

  1. Soil conductivity rises with temperature, so uncorrected maps mix weather with soil
  2. The sensor's GNSS receiver drifts with temperature and must be re-surveyed
  3. Clay content changes with temperature, so the reference fixes the clay reading
  4. Salinity is created by warm weather, so readings taken on warm days must always be discarded
Answer and working

A. Soil conductivity rises with temperature, so uncorrected maps mix weather with soil

Ionic conduction increases with temperature, so readings are corrected to 25 °C for comparison. Clay content and salinity do not change daily with temperature; GNSS drift is unrelated.

Question 6 · medium

Besides saving input, why is the as-applied coverage map from section control useful to a farm business?

  1. It replaces the need to calibrate the sprayer because rates are now measured
  2. It is a record of what product was applied, where and at what rate, for compliance
  3. It proves the crop yield of each section, so a yield monitor is no longer needed at harvest time
  4. It sets the correction service subscription according to the area covered
Answer and working

B. It is a record of what product was applied, where and at what rate, for compliance

The coverage map is an as-applied record usable for pesticide records, buyer audits and buffer-zone checks. It does not replace calibration or yield measurement and is unrelated to correction subscriptions.

Question 7 · easy

ISOBUS is the common name for which international standard?

  1. ISO 9001
  2. ISO 14001
  3. ISO 11783
  4. ISO 730
Answer and working

C. ISO 11783

ISO 11783 defines the serial control and communications data network for tractors and implements. ISO 9001 and 14001 are management-system standards; ISO 730 covers the three-point linkage.

Question 8 · medium

ISOBUS is built on which network technology and at what bit rate?

  1. Ethernet at 100 Mbit/s with IP addresses
  2. RS-232 serial at 9600 bit/s
  3. CAN with 29-bit identifiers at 250 kbit/s
  4. CAN with 11-bit standard identifiers at 1 Mbit/s
Answer and working

C. CAN with 29-bit identifiers at 250 kbit/s

ISO 11783 uses CAN 2.0B extended frames with 29-bit identifiers at 250 kbit/s, following SAE J1939. 11-bit identifiers at 1 Mbit/s is typical of other CAN uses; Ethernet and RS-232 are not the ISOBUS physical layer.

Question 9 · easy

Which AEF ISOBUS functionality lets an implement control certain tractor functions, such as speed or hydraulics, under defined safety rules?

  1. TC-BAS
  2. AUX
  3. UT
  4. TIM
Answer and working

D. TIM

Tractor Implement Management (TIM) lets the implement command tractor functions. TC-BAS records totals, AUX is auxiliary control such as a joystick, and UT is the universal (virtual) terminal.

Question 10 · medium

A spreader's as-applied file is imported with the rate interpreted as lb/acre instead of kg/ha. What happens to the reported rates?

  1. Rates are unaffected because the import software converts all values automatically
  2. Only the field boundary is affected; rate values stay correct in every cell
  3. Every rate is wrong by a factor of about 1.12, so totals and costs are misreported
  4. The rates are wrong by a factor of 10, which is easy to spot on a map
Answer and working

C. Every rate is wrong by a factor of about 1.12, so totals and costs are misreported

1 lb/acre = 1.12 kg/ha, so mislabelled units give values about 12 % out — small enough to go unnoticed, which is why units must be carried in metadata. Software cannot convert what it misreads, boundaries are separate, and the factor is not 10.

A study plan for Precision Agriculture & System Management in Landbased Technician Accreditation

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (58% of the 24 questions): ISOBUS basics (6, 25%); Auto-steer and guidance (4, 17%); Section control (4, 17%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: GNSS and RTK positioning (3, 13%); Yield monitoring (3, 13%); Farm data management (2, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Prescription maps (1, 4%); Proximal and remote sensing for crops (1, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: GNSS and RTK positioning (1 hard of 3), ISOBUS basics (1 hard of 6).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Prescription maps (1 easy of 1); ISOBUS basics (3 easy of 6).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Landbased Technician Accreditation Precision Agriculture & System Management

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.