India · Ministry of Agriculture & Farmers Welfare, Government of India · secondary source
Farm Machinery Training & Testing Institutes (Budni, Hisar, Anantapur, Biswanath Chariali) is a professional certification run by Ministry of Agriculture & Farmers Welfare, Government of India, for candidates in India.
Not an exam: short training courses and machinery testing (commercial, batch, confidential, CMVR).
We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose.
Check the current format, eligibility, fees and dates on the official site: nerfmtti.nic.in.
The main site refused connection during research; OECD accreditation of CFMTTI Budni is from a search snippet and needs re-verification.
Our reading of the syllabus, from the questions we have written to this exam; the exam body's own weighting, where published, is under Format above.
Start here: read these subjects' manuals first and work their questions until the reasoning is automatic.
One pass per subject, then mixed sets across them.
Definitions, classifications and standard figures; quick to revise, easy marks to lose.
Leave untimed time for these and read every explanation, including for the options you rejected.
Official source: nerfmtti.nic.in
Original questions written to this exam's published syllabus and pattern. Not past papers.
1. After fitting a replacement piston motor to a harvester's header drive, a mechanic plugs its case-drain port because no drain hose came with it. The likely result is
A. case pressure builds with leakage oil until the shaft seal blows out
Internal leakage collects in the motor case; if it cannot drain freely to tank, case pressure builds until the shaft seal, which is rated for low pressure, fails. Plugging the drain does not make leakage disappear or raise speed, and it does not change the direction of rotation.
Hydraulic Drives & Controls · Hydraulic motors
2. The engine most commonly fitted to a walk-behind two-wheel power tiller is a
D. single-cylinder horizontal diesel
Power tillers use a small single-cylinder horizontal four-stroke diesel, often water-cooled with a radiator or hopper. Multi-cylinder turbocharged diesels power four-wheel tractors.
Tractor & Automotive Engines (IC Engines) · Engine classification and terminology
3. Before an operator dismounts to unblock a PTO-driven implement, the correct action is to
D. disengage the PTO, stop the engine, remove the key and wait for parts to stop
A rotating PTO shaft winds in clothing in a fraction of a second. Only a stopped engine and stationary shaft are safe.
Tractor Systems & Controls · Power take-off: standards and speeds
4. In a four-stroke engine the camshaft rotates at
A. half the crankshaft speed
Each valve opens once per cycle, and a cycle takes two crank revolutions, so the camshaft (and the injection-pump camshaft) turns at half crank speed.
Tractor & Automotive Engines (IC Engines) · Two-stroke and four-stroke engines
5. A tractor costing 700,000 is used 1,000 h/yr. Repair and maintenance are 10 % of price per year; it uses 5 L/h of diesel at 90/L; lubrication is 15 % of fuel cost; the operator costs 80/h. What is its variable cost per hour?
B. 667.5/h
R&M = 70,000/1,000 = 70; fuel = 450; lubrication = 67.5; operator = 80. Total = 667.5 per hour. Omitting lubrication gives 600.0; omitting the operator gives 587.5; spreading R&M over 100 h gives 1297.5.
Farm Machinery Management & Economics · Variable costs: repair and maintenance, fuel and labour
6. ISO 730 defines categories (1, 2, 3, 4 and narrow variants) for the rear three-point linkage of agricultural tractors. What does the category mainly specify?
C. The hitch-pin diameters and the spacing of the linkage attachment points
Categories match tractor power ranges and fix the pin diameters and spacing so implements fit tractors of the same category. Pump pressure and control mode are not set by ISO 730, and quick couplers are covered by other standards such as ISO 5675 and ISO 16028.
Hydraulic Drives & Controls · Tractor hydraulic systems
7. A boom sprayer must apply 300 L/ha at 6 km/h with nozzles 0.5 m apart. The discharge required from each nozzle is
A. 1.50 L/min
q = rate × v × w/600 = 300 × 6 × 0.5/600 = 1.50 L/min. 15.0 uses 60; 16.67 (= 10 000 × 0.5/300) mixes up the unit constants and is not a nozzle flow; 3.00 forgets the nozzle spacing and is the flow per metre of boom.
Farm Machinery Testing, Evaluation & Standards · Tests of sprayers and harvesting equipment
8. A state research station has built the first working unit of a new self-propelled paddy transplanter and wants to know whether the design is sound enough to be taken to production. The appropriate test is a
A. prototype or initial test, with extended field running to expose design faults
A prototype (initial) test examines a new design before production, usually including extended field running. A batch test needs an existing production line and an earlier commercial test; a commercial test is for a production model; a ROPS test applies to tractors and similar machines with protective structures, not as a general first step.
Farm Machinery Testing, Evaluation & Standards · Types of tests: commercial, batch, confidential and prototype
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.