USA · Irrigation Association
Irrigation Association Certified Agricultural Irrigation Specialist (CAIS) is a professional certification run by Irrigation Association, for candidates in USA.
100 MCQs, 3 hours.
For irrigation managers and specialists rather than designers.
Our reading of the syllabus, from the questions we have written to this exam; the exam body's own weighting, where published, is under Format above.
Start here: read these subjects' manuals first and work their questions until the reasoning is automatic.
One pass per subject, then mixed sets across them.
Definitions, classifications and standard figures; quick to revise, easy marks to lose.
Leave untimed time for these and read every explanation, including for the options you rejected.
Official source: irrigation.org
Original questions written to this exam's published syllabus and pattern. Not past papers.
1. A drip system draws from an open farm pond with heavy algae growth in summer. Which primary filter is most appropriate?
A. Media (sand/gravel) filter, backflushable
Media filters trap organic material in the depth of the bed and are backflushed; they are the standard primary filter for surface water with algae. A screen alone clogs quickly with algae; a hydrocyclone does not remove organic matter; chlorination complements, but does not replace, filtration.
Sprinkler & Micro-Irrigation Systems · Filtration
2. What distinguishes an in-line emitter from an on-line emitter?
A. In-line emitters are built into the tubing during manufacture; on-line emitters are punched into it later
The distinction is physical: in-line emitters are inserted or formed inside the tube at the factory at fixed spacing (as in dripline and tape); on-line emitters are inserted into punched holes in the field at chosen spacings. Either type can be pressure-compensating.
Sprinkler & Micro-Irrigation Systems · Drip system components
3. In the SAR formula, concentrations of Na⁺, Ca²⁺ and Mg²⁺ must be expressed in:
C. meq/L (mmolc/L)
SAR = Na/√((Ca + Mg)/2) uses milliequivalents per litre of the water or extract. Using mg/L is the commonest error; g/kg and percent of CEC describe exchangeable quantities on the soil, which belong in ESP, not SAR.
Soil Science for Engineers · Sodicity: SAR and ESP
4. The permanent wilting point is conventionally estimated as the soil water content at a matric potential of:
C. −1,500 kPa (−15 bar)
PWP is conventionally taken at −1,500 kPa. −33 kPa is the usual laboratory field capacity for medium and fine soils, −10 kPa is used for field capacity of sands, and about −3,100 kPa is the hygroscopic coefficient.
Soil Science for Engineers · Soil water: field capacity, wilting point and available water
5. A sprinkler lateral is laid down a uniform gentle slope from its inlet. Compared with the same lateral on level ground, what does the slope do?
C. Elevation gain offsets friction, so a longer lateral or smaller pipe can meet the same pressure limit
Going downhill, each metre of fall adds pressure that offsets friction loss; on gentle slopes the profile flattens and the allowable length grows. On steep slopes the gain can exceed friction and the end pressure rises, which again needs checking.
Sprinkler & Micro-Irrigation Systems · Allowable pressure variation and the friction factor F
6. The osmotic effect of soil salinity on crops:
C. Lowers soil-water potential so plants take up water with more difficulty, as in drought
Dissolved salts lower the osmotic potential of soil water. Specific-ion toxicity (sodium, chloride, boron) is a separate effect, and sodicity (ESP) mainly affects soil structure.
Agricultural Drainage Engineering · Salinity and the leaching requirement
7. Where should tensiometers be installed to schedule a deep-rooted row crop?
B. One in the upper root zone to trigger irrigation and one near its bottom to check that water reached it without excess drainage
Most extraction is in the upper root zone, so the trigger sensor goes there; a deeper sensor shows whether the irrigation refilled the lower zone or drained past it. Surface readings fluctuate with evaporation, and sensors below the roots do not see crop use.
Irrigation Engineering (Soil-Water-Plant, Conveyance, Surface Methods) · Irrigation scheduling
8. In chemigation safety equipment, where is the main check valve placed?
B. In the irrigation line between the water source/pump and the injection point
The irrigation-line check valve prevents water containing chemicals from flowing back to the well or source; it sits between the pump and the injection point, with a vacuum-relief valve and low-pressure drain upstream of it. The injection line has its own check valve as well.
Sprinkler & Micro-Irrigation Systems · Fertigation
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.