Irrigation Association Certified Agricultural Irrigation Specialist (CAIS) · USA · Irrigation Association
Original practice questions written to the published syllabus · not past papersIrrigation Association Certified Agricultural Irrigation Specialist (CAIS) is a professional certification run by Irrigation Association, for candidates in USA. 100 MCQs, 3 hours.
Source: irrigation.org.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
How much water a crop needs, when to give it, how to measure and convey it, and how to design surface irrigation.
Our 21 Irrigation Association Certified Agricultural Irrigation Specialist questions in this subject: 3 easy, 13 medium, 5 hard, across 9 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to Irrigation Association Certified Agricultural Irrigation Specialist and are not shown on any other exam's page.
A clay loam has volumetric field capacity 0.32 and wilting point 0.14. With a 1.2 m root zone and a management allowed depletion of 50 %, what is the readily available water?
D. 108 mm
TAW = 1000 × (0.32 − 0.14) × 1.2 = 216 mm. RAW = 0.5 × 216 = 108 mm. 216 mm is TAW, not RAW; 192 mm applies MAD to field capacity alone; 84 mm applies it to the wilting point water, which is unavailable.
When sizing the pump and main pipeline for a new irrigation system, which crop water figure should normally govern capacity?
A. Peak-period ETc (net of dependable rain) for the design year, divided by efficiency and adjusted for operating hours
Capacity must meet the highest sustained demand; averaging over the season or year undersizes the system and causes stress in the peak period. Operating hours per day and efficiency then convert the net peak rate to a flow.
Total available water in the root zone is 150 mm, MAD is 40 % and peak ETc is 6 mm/day. What is the irrigation interval at peak?
D. 10 days
Allowable depletion = 0.40 × 150 = 60 mm; interval = 60/6 = 10 days. 25 days uses the full TAW; 15 days uses MAD = 0.6; 6 days confuses ETc with the interval.
A 3 ft³/s stream is applied to a 12-acre field for 10 hours. Roughly what average depth is applied?
A. 2.5 in
1 ft³/s for 1 hour ≈ 1 acre-inch (1.008). Q t = A d gives d = 3 × 10 / 12 = 2.5 in (more exactly 2.52 in). 0.25 in is a decimal slip; 30 in forgets to divide by area; 4 in divides area by flow.
Where should tensiometers be installed to schedule a deep-rooted row crop?
B. One in the upper root zone to trigger irrigation and one near its bottom to check that water reached it without excess drainage
Most extraction is in the upper root zone, so the trigger sensor goes there; a deeper sensor shows whether the irrigation refilled the lower zone or drained past it. Surface readings fluctuate with evaporation, and sensors below the roots do not see crop use.
A 3-ft Parshall flume reads Ha = 0.50 ft and Hb = 0.40 ft. Which is correct?
C. Submergence is 80 %, above the 70 % free-flow limit for this size, so a submergence correction must be applied
Submergence = Hb/Ha = 0.40/0.50 = 80 %. For 1–8 ft flumes free flow holds up to 70 %, so the flow is submerged and the free-flow rating overstates discharge unless corrected. 125 % inverts the ratio; 20 % is 1 − Hb/Ha.
A buried plastic pipeline 300 m long, 200 mm internal diameter, carries 30 L/s. Using Hazen-Williams with C = 150 (SI: hf = 10.67 L Q^1.852 / (C^1.852 D^4.87)), what is the friction loss?
C. 1.14 m
hf = 10.67 × 300 × 0.03^1.852 / (150^1.852 × 0.2^4.87) = 1.14 m. 10× results from taking L as 3,000 m; 0.039 m uses a 400 mm pipe (diameter doubled); 2.43 m uses C = 100, a value for old rough pipe, not plastic.
Which pair of factors most determines the uniformity achieved in a level basin?
A. Precision of land levelling and inflow rate relative to the soil intake rate
Level basins depend on fast, even coverage: a precisely levelled surface and a large stream relative to intake make opportunity time nearly uniform. Dike size matters only for containing the depth.
Compared with a sandy soil, how should furrow spacing typically be set on a clay soil?
C. Wider, as clay spreads water sideways more
In clays, capillary forces spread water sideways well relative to downward movement, so the wetted bulb is wide and furrows can be farther apart. In sands, water moves mostly downward, so furrows must be closer. Clay usually has a lower, not higher, intake rate.
Catch-can depths along a field (mm) are 10, 12, 8, 14, 6 and 10. What is Christiansen's coefficient of uniformity?
B. 80.0 %
Mean = 10 mm; absolute deviations 0, 2, 2, 4, 4, 0 sum to 12. CU = 100 (1 − 12 / (6 × 10)) = 80.0 %. 60 % is the minimum divided by the mean; −20 % forgets to divide by n; 86.7 % uses the range instead of summed deviations.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.