ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR
Original practice questions written to the published syllabus · not past papersICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.
Source: icar.org.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Single-answer MCQs on soil-water constants and their suctions, ET methods and pan coefficients, weirs and flumes, duty and delta, Lacey and Kennedy regime relations, lining types and surface-method definitions, with short calculations.
How much water a crop needs, when to give it, how to measure and convey it, and how to design surface irrigation.
Our 72 ICAR AIEEA-PG questions in this subject: 29 easy, 34 medium, 9 hard, across 14 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.
In the gravimetric method, soil samples are dried to constant mass at what temperature?
A. 105 °C
Soil is dried at 105 °C (usually about 24 h) to remove water without burning organic matter. 60 °C is used for plant tissue and leaves water in soil; higher temperatures begin to oxidise organic matter and remove structural water.
A 90° V-notch weir operates with a head of 0.20 m. Using Q = 1.38 H^2.5 (SI), what is the discharge?
D. 24.7 L/s
Q = 1.38 × 0.20^2.5 = 1.38 × 0.01789 = 0.0247 m³/s = 24.7 L/s. 123 L/s uses the rectangular exponent 1.5; 42.3 L/s omits the discharge coefficient (Cd ≈ 0.58); 2.47 L/s is a unit slip.
The side slopes of a Cipolletti weir are:
B. 1 horizontal to 4 vertical
Cipolletti chose 1H:4V so that the added flow through the sloping sides offsets the end contractions, giving Q = 1.86 L H^1.5 (SI) with no contraction correction. 1:1 sides make a 90° notch-like trapezoid, and 4H:1V is far too flat.
For the same canal (Q = 50 m³/s) with silt factor f = 1.0, what is Lacey's regime velocity?
B. 0.84 m/s
V = (Q f² / 140)^(1/6) = (50 × 1 / 140)^(1/6) = 0.357^(1/6) = 0.84 m/s. 4.37 multiplies by 140; 0.71 uses a cube root; 0.36 omits the sixth root.
By Kennedy's theory, what is the critical (non-silting, non-scouring) velocity in a channel 2.0 m deep with critical velocity ratio m = 1.0?
D. 0.86 m/s
V₀ = 0.55 m D^0.64 = 0.55 × 1.0 × 2^0.64 = 0.55 × 1.558 = 0.86 m/s. 1.10 treats the exponent as 1; 0.55 ignores depth; 0.71 uses the wrong exponent.
In a low-pressure buried pipeline for surface irrigation, what is the main function of the inlet (pump) stand?
B. To provide head, release entrained air and damp pressure surges
The open inlet stand sets the hydraulic grade line, lets air escape and acts as a surge relief. It is not a filter, a measurement of ET or a storage reservoir.
A buried pipeline must carry 40 L/s with a velocity not exceeding 1.5 m/s. What is the minimum internal diameter?
C. 184 mm
A = Q/V = 0.040/1.5 = 0.0267 m²; D = √(4A/π) = 184 mm. 163 mm takes A = D² (forgets π/4); 92 mm uses the radius formula as diameter; 583 mm takes 40 L/s as 0.4 m³/s.
Using the empirical relation Qmax = 0.6/S (Q in L/s, S in %), what is the maximum non-erosive stream for a furrow on a 0.4 % slope?
D. 1.5 L/s
Qmax = 0.6 / 0.4 = 1.5 L/s. 0.24 multiplies; 150 L/s uses the slope as a fraction (0.004) in a formula written for percent; 0.15 is a decimal slip.
Under Criddle's quarter-time rule of thumb, if the required infiltration opportunity time for a furrow is 8 h, the advance time to the end of the furrow should be about:
C. 2 h
The rule sets advance time at about one quarter of the required opportunity time: 8/4 = 2 h. 4 h is half; 8 h would leave the tail badly under-irrigated; 0.25 h confuses the fraction with the time.
A distributary runs for 12 days in each 20-day rotation period. What is its time factor?
C. 0.6
Time factor = days the channel runs / days in the period = 12/20 = 0.6. 1.67 inverts it; 0.4 is the idle fraction; 12 is the number of days, not a ratio.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.