LAISHA
Open Laisha

ICAR AIEEA-PG Engineering Mechanics (Statics & Dynamics): practice questions

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
65written to this exam in this subject
11syllabus units

About ICAR AIEEA-PG

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Engineering Mechanics (Statics & Dynamics) in ICAR AIEEA-PG

Unit IV names engineering mechanics alongside strength of materials and soil mechanics. Expect definitions (Varignon, Lami, D'Alembert, angle of repose, self-locking), standard centroid and moment-of-inertia results, truss determinacy and zero-force members, belt friction ratio and short numericals. Question papers are not published, so emphasis is inferred from the syllabus.

Forces, equilibrium and motion of particles and rigid bodies: the starting point for structures, machines and tractor mechanics.

Our 65 ICAR AIEEA-PG questions in this subject: 21 easy, 26 medium, 18 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.

Question 1 · easy

A square-threaded screw jack lifting a trailer holds the load without a brake when the handle is released. This is because:

  1. The helix angle alpha is greater than the friction angle phi
  2. The efficiency of the jack is greater than fifty per cent
  3. The lead of the thread is greater than its mean diameter
  4. The friction angle phi is greater than the helix angle alpha
Answer and working

D. The friction angle phi is greater than the helix angle alpha

The lowering torque is W (dm/2) tan(phi - alpha); if phi > alpha it is positive, so torque must be applied to lower the load: the screw is self-locking. A self-locking square-thread screw has efficiency below 50 per cent.

Question 2 · hard

A single-start square-threaded jack has a pitch of 6 mm, a mean diameter of 30 mm and a thread friction coefficient of 0.12. Ignoring collar friction, what is its efficiency when raising a load?

  1. 34.4 %
  2. 53.1 %
  3. 88.0 %
  4. 20.0 %
Answer and working

A. 34.4 %

tan alpha = 6 / (pi x 30) = 0.0637, alpha = 3.64 deg; phi = arctan 0.12 = 6.84 deg. Efficiency = tan alpha / tan(alpha + phi) = 0.0637 / 0.1851 = 34.4 %. Since phi > alpha the jack is self-locking, consistent with an efficiency below 50 %. 53.1 % divides tan alpha by mu (0.0637 / 0.12); 88.0 % is 1 - mu; 20.0 % uses pitch/diameter without pi (6 / 30).

Question 3 · easy

The centroid of a triangular plate lies at what distance from its base, measured along the height h?

  1. h/2
  2. 2h/3
  3. h/3
  4. h/4
Answer and working

C. h/3

The centroid is where the medians meet, one-third of the height from the base (two-thirds from the apex). h/4 is the centroid of a solid cone from its base. h/2 is mid-height, not the centroid; 2h/3 is the distance from the apex.

Question 4 · hard

An engine flywheel is a solid disc of mass 80 kg and radius 0.3 m running at 1200 rev/min. How much kinetic energy does it store?

  1. 5184 kJ
  2. 28.42 kJ
  3. 113.70 kJ
  4. 0.720 kJ
Answer and working

B. 28.42 kJ

I = m r^2 / 2 = 0.5 x 80 x 0.09 = 3.60 kg m2; omega = 2 pi x 1200 / 60 = 125.66 rad/s; KE = 0.5 I omega^2 = 28.42 kJ. Using rev/min directly and dropping the 1/2 gives 5184 kJ; treating the disc as a ring (I = m r^2) and also dropping the 1/2 quadruples it (113.70 kJ); using rev/s without 2 pi gives 0.720 kJ, far too small.

Question 5 · medium

The perpendicular axis theorem, Iz = Ix + Iy, can be applied to:

  1. Any three-dimensional solid about any three perpendicular axes
  2. Only circular areas, where Ix and Iy are equal about diameters
  3. Any body, provided the axes pass through its centre of gravity
  4. Plane areas and thin flat plates (laminae), with z normal to the plane
Answer and working

D. Plane areas and thin flat plates (laminae), with z normal to the plane

The theorem needs all the mass or area to lie in the xy plane, so that r^2 = x^2 + y^2 for every element. For a solid body it does not hold. For a circle it gives J = 2 I_diameter.

Question 6 · easy

A wheel rolls without slipping on level ground; its centre moves at speed v. What is the speed of the point at the top of the wheel?

  1. v
  2. 2v
  3. zero
  4. v/2
Answer and working

B. 2v

The contact point is the instantaneous centre of zero velocity. The top of the wheel is twice as far from it as the centre, so it moves at 2v. The contact point itself is momentarily at rest.

Question 7 · easy

D'Alembert's principle converts a dynamics problem into one of equilibrium by:

  1. Replacing all external forces by one resultant acting through the instantaneous centre of rotation
  2. Setting the body's acceleration to zero, since at every single instant the body is in static equilibrium
  3. Adding the weight of the body a second time at its centre of mass to account for the extra load of acceleration
  4. Adding an inertia force equal to -m a at the centre of mass, then applying the equations of statics
Answer and working

D. Adding an inertia force equal to -m a at the centre of mass, then applying the equations of statics

Writing sum F - m a = 0 treats -m a as an extra, fictitious inertia force. The body is then in dynamic equilibrium and moments can be taken about any point. For a rotating rigid body an inertia couple -I alpha is also added.

Question 8 · hard

Using a rigid-body model on level ground, a tractor with a 1.4 m track and a centre of gravity 1.0 m high turns on a 12 m radius. Assuming the tyres do not skid, at what speed does it begin to overturn outward?

  1. 12.84 m/s
  2. 12.97 m/s
  3. 82.40 m/s
  4. 9.08 m/s
Answer and working

D. 9.08 m/s

Tipping about the outer wheels when m v^2/r x h = m g x b/2, so v = sqrt(g r b / (2h)) = sqrt(9.81 x 12 x 0.7 / 1.0) = 9.08 m/s. Using the full track gives 12.84; 82.40 forgets the square root; 12.97 m/s swaps h and b/2 (sqrt(9.81 x 12 x 1.0 / 0.7)). Real tractors overturn at lower speeds because of tyre deflection, slopes and bumps.

Question 9 · easy

In a collision between two bodies, the coefficient of restitution e = 0 means the impact is:

  1. Perfectly elastic: kinetic energy is fully conserved
  2. Impossible: every real collision has some rebound
  3. Perfectly plastic: the bodies move together after impact
  4. Explosive: the bodies separate faster than they met
Answer and working

C. Perfectly plastic: the bodies move together after impact

e = relative separation speed / relative approach speed. e = 0 means no separation: the bodies stay together, and the kinetic-energy loss is greatest. e = 1 is perfectly elastic. Momentum is conserved in both.

Question 10 · medium

In a test of grain damage, a kernel dropped from 1.0 m onto a steel plate rebounds to 0.36 m. What is the coefficient of restitution?

  1. 0.36
  2. 0.64
  3. 0.60
  4. 0.80
Answer and working

C. 0.60

Impact speed is sqrt(2 g h0) and rebound speed sqrt(2 g h1), so e = sqrt(h1 / h0) = sqrt(0.36) = 0.60. The height ratio 0.36 is e^2, the fraction of kinetic energy retained. Measured values for grain vary with moisture content, variety and surface. 0.64 is 1 - 0.36; 0.80 is the square root of that.

A study plan for Engineering Mechanics (Statics & Dynamics) in ICAR AIEEA-PG

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (46% of the 65 questions): Friction, including belt friction (8, 12%); Impulse and momentum (8, 12%); Centroid and centre of gravity (7, 11%); Kinematics of particles and rigid bodies (7, 11%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Analysis of trusses and frames (6, 9%); Free-body diagrams and equilibrium (6, 9%); Area and mass moment of inertia (5, 8%); Force systems and resultants (5, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Kinetics: Newton's laws and D'Alembert's principle (5, 8%); Virtual work (4, 6%); Work-energy principle (4, 6%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Kinetics: Newton's laws and D'Alembert's principle (3 hard of 5), Work-energy principle (2 hard of 4), Impulse and momentum (3 hard of 8).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Centroid and centre of gravity (3 easy of 7); Area and mass moment of inertia (2 easy of 5).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG Engineering Mechanics (Statics & Dynamics)

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.