LAISHA
Open Laisha

NCEES FE Other Disciplines Engineering Mechanics (Statics & Dynamics): practice questions

NCEES FE Other Disciplines · USA · NCEES

Original practice questions written to the published syllabus · not past papers
10worked here, free
70written to this exam in this subject
11syllabus units

About NCEES FE Other Disciplines

NCEES FE Other Disciplines is a licensing and registration exam run by NCEES, for candidates in USA. Computer-based, 110 questions, 6-hour appointment (5 h 20 min exam).

Source: ncees.org.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Engineering Mechanics (Statics & Dynamics) in NCEES FE Other Disciplines

Statics (9-14 questions): resultants, equilibrium of rigid bodies, trusses and frames, centroids, area moments of inertia, static friction. Dynamics (9-14 questions): particle and rigid-body kinematics, Newton's second law, work-energy, impulse-momentum. Almost all are short numerical problems solved with the NCEES Reference Handbook, so speed with FBDs and unit handling decides the score.

Forces, equilibrium and motion of particles and rigid bodies: the starting point for structures, machines and tractor mechanics.

Our 70 NCEES FE Other Disciplines questions in this subject: 19 easy, 32 medium, 19 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to NCEES FE Other Disciplines and are not shown on any other exam's page.

Question 1 · medium

At an unloaded truss joint, three members meet; two of them are collinear. What can be said about the third member?

  1. It is a zero-force member under this loading
  2. It carries the same force as each collinear member
  3. It carries the sum of the two collinear forces
  4. It must be in compression to hold the joint
Answer and working

A. It is a zero-force member under this loading

Resolve perpendicular to the collinear pair: only the third member has a component in that direction, and no load acts, so its force is zero. Zero-force members still matter: they brace compression members and carry load when the loading changes.

Question 2 · medium

A T-section toolbar has a flange 120 mm wide by 20 mm thick on top of a web 20 mm thick and 100 mm deep. How far is the centroid above the bottom of the web?

  1. 60.0 mm
  2. 80.0 mm
  3. 82.7 mm
  4. 37.3 mm
Answer and working

C. 82.7 mm

Flange: A = 2400 mm2 at y = 110 mm; web: A = 2000 mm2 at y = 50 mm. y-bar = (2400 x 110 + 2000 x 50) / 4400 = 82.7 mm. 60 mm is half the total depth; 80 mm averages the part centroids without weighting by area; 37.3 mm is measured from the top.

Question 3 · easy

A rectangular steel bar 50 mm wide and 100 mm deep is used as a beam. What is its second moment of area about the horizontal centroidal axis (bending about the 100 mm depth)?

  1. 1.042 x 10^6 mm4
  2. 16.667 x 10^6 mm4
  3. 1.389 x 10^6 mm4
  4. 4.167 x 10^6 mm4
Answer and working

D. 4.167 x 10^6 mm4

I = b h^3 / 12 = 50 x 100^3 / 12 = 4166667 mm4. Swapping b and h gives the weak-axis value; b h^3/3 is about the base; b h^3/36 is the triangle formula.

Question 4 · medium

A 40 mm wide by 60 mm deep rectangle forms part of a chassis section. Its centroid is 50 mm from the section's neutral axis, which is parallel to the 40 mm side. What is its second moment of area about the neutral axis?

  1. 0.720 x 10^6 mm4
  2. 6.000 x 10^6 mm4
  3. 0.840 x 10^6 mm4
  4. 6.720 x 10^6 mm4
Answer and working

D. 6.720 x 10^6 mm4

I = I_c + A d^2 = 40 x 60^3/12 + 2400 x 50^2 = 720000 + 6000000 = 6720000 mm4. Leaving out either term, or using d instead of d^2, gives the other options.

Question 5 · hard

A tractor accelerates a 2000 kg trailer at 0.5 m/s2 on level ground. The trailer's rolling resistance is 1.2 kN. What is the horizontal force in the hitch?

  1. 1.0 kN
  2. 2.2 kN
  3. 1.2 kN
  4. 11.01 kN
Answer and working

B. 2.2 kN

For the trailer alone: hitch force - rolling resistance = m a, so hitch force = 2000 x 0.5 + 1200 = 2200 N = 2.2 kN. Leaving out the resistance gives 1.0 kN and leaving out the acceleration term gives 1.2 kN; using weight instead of mass in m a gives a far larger figure.

Question 6 · medium

A front loader raises an 800 kg round bale through 2.5 m in 4 s at steady speed. What is the average useful power delivered to the bale?

  1. 0.50 kW
  2. 4.91 kW
  3. 19.62 kW
  4. 78.48 kW
Answer and working

B. 4.91 kW

Work = m g h = 800 x 9.81 x 2.5 = 19620 J; power = 19.62 kJ / 4 s = 4.91 kW. Using mass instead of weight gives 0.50 kW; 19.62 is the energy in kJ, not a power. The hydraulic pump must supply more because of losses. 78.48 kW multiplies the energy by the time.

Question 7 · medium

A trailer starts from rest and rolls freely down a ramp, dropping 2 m in height. Ignoring friction and wheel rotational inertia, what is its speed at the bottom?

  1. 4.43 m/s
  2. 39.24 m/s
  3. 19.62 m/s
  4. 6.26 m/s
Answer and working

D. 6.26 m/s

Energy conservation: m g h = 0.5 m v^2, v = sqrt(2 g h) = sqrt(2 x 9.81 x 2) = 6.26 m/s. The result is independent of mass and of the ramp shape. Omitting the square root gives 39.24. 4.43 m/s drops the 2 (sqrt(g h)); 19.62 is g h itself.

Question 8 · medium

A 3500 kg tractor reversing at 1.5 m/s couples automatically to a stationary 1500 kg trailer and they move off together. What is their common speed just after coupling?

  1. 1.25 m/s
  2. 0.45 m/s
  3. 0.75 m/s
  4. 1.05 m/s
Answer and working

D. 1.05 m/s

Momentum is conserved: 3500 x 1.5 = 5000 v, v = 1.05 m/s. 1.25 m/s comes from wrongly conserving kinetic energy, which is not conserved in a coupling (plastic) impact; 0.45 m/s uses the trailer's mass in the numerator. 0.75 m/s simply halves the tractor's speed.

Question 9 · hard

Grain leaves a conveyor at 3 kg/s moving horizontally at 4 m/s, strikes a deflector and leaves it moving vertically downward at 4 m/s. What is the magnitude of the force the grain exerts on the deflector?

  1. 12.00 N
  2. 16.97 N
  3. 24.00 N
  4. 0.00 N
Answer and working

B. 16.97 N

F = m-dot x change in velocity. The velocity change has components -4 (horizontal) and -4 (vertical), magnitude 4 sqrt 2 = 5.66 m/s. F = 3 x 5.66 = 16.97 N. 12 N counts only one component; zero wrongly assumes that an unchanged speed means no force. 24.00 N adds the two components arithmetically (3 x 8).

Question 10 · medium

A frictionless screw jack has a lead of 10 mm and a handle radius of 0.25 m. What handle force holds a 15 kN load?

  1. 600 N
  2. 95493 N
  3. 95.5 N
  4. 191.0 N
Answer and working

C. 95.5 N

One turn: effort moves 2 pi x 0.25 = 1.571 m, load moves 0.010 m. P x 1.571 = 15000 x 0.010, P = 95.5 N. Leaving out 2 pi gives 600 N; leaving the lead in millimetres gives a figure 1000 times too large. Real jacks need more because of friction. 191.0 N takes 0.25 m as the handle diameter (pi x 0.25).

A study plan for Engineering Mechanics (Statics & Dynamics) in NCEES FE Other Disciplines

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (43% of the 70 questions): Kinetics: Newton's laws and D'Alembert's principle (8, 11%); Work-energy principle (8, 11%); Analysis of trusses and frames (7, 10%); Area and mass moment of inertia (7, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Free-body diagrams and equilibrium (7, 10%); Impulse and momentum (7, 10%); Force systems and resultants (6, 9%); Friction, including belt friction (6, 9%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Kinematics of particles and rigid bodies (6, 9%); Centroid and centre of gravity (4, 6%); Virtual work (4, 6%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Impulse and momentum (4 hard of 7), Centroid and centre of gravity (2 hard of 4), Kinetics: Newton's laws and D'Alembert's principle (3 hard of 8).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Virtual work (2 easy of 4); Kinetics: Newton's laws and D'Alembert's principle (3 easy of 8).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — NCEES FE Other Disciplines Engineering Mechanics (Statics & Dynamics)

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.