Nepal Engineering Council Registration Exam — Agricultural Engineering · Nepal · Nepal Engineering Council
Original practice questions written to the published syllabus · not past papersNepal Engineering Council Registration Exam — Agricultural Engineering is a licensing and registration exam run by Nepal Engineering Council, for candidates in Nepal.
Official site: nec.gov.np.
We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.
Forces, equilibrium and motion of particles and rigid bodies: the starting point for structures, machines and tractor mechanics.
Our 25 Nepal Engineering Council Registration Exam questions in this subject: 10 easy, 14 medium, 1 hard, across 9 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to Nepal Engineering Council Registration Exam and are not shown on any other exam's page.
Two chains pull on a tree stump from one ring with forces of 6 kN and 4 kN; the angle between the chains is 120 degrees. What is the magnitude of the resultant pull on the stump?
D. 5.29 kN
R = sqrt(P^2 + Q^2 + 2PQ cos theta) = sqrt(36 + 16 + 2 x 6 x 4 x cos 120) = sqrt(28) = 5.29 kN. Using +cos 60 instead of cos 120 gives 8.72 kN; treating the chains as perpendicular gives 7.21 kN; adding arithmetically gives 10 kN, which is only right for chains pulling in the same direction.
The top link of a tractor's three-point hitch is pinned at both ends and carries no load between them. Ignoring its own weight, its force must act:
D. Along the straight line joining its two pin centres
A member loaded only at two pins is a two-force member; equilibrium requires the two end forces to be equal, opposite and collinear, so the force lies along the line joining the pins. That is why the top link is either in tension or in compression.
A 4 m simply supported beam in a feed store carries a 6 kN point load 1 m from the left support. What is the left support reaction?
C. 4.5 kN
Moments about the right support: RA x 4 = 6 x 3, RA = 4.5 kN, and RB = 6 - 4.5 = 1.5 kN. The nearer support carries more; 1.5 kN reverses the arms and 3 kN assumes a central load.
A plane pin-jointed roof truss has 7 joints and is supported by one pin and one roller. How many members does it need to be simple and statically determinate?
D. 11
For a plane truss, m = 2j - 3 = 2 x 7 - 3 = 11. Using 2j gives 14; forgetting the 3 rigid-body equations is the common slip. More than 11 members makes it indeterminate; fewer makes it a mechanism. 10 uses j + 3; 12 subtracts only the two pin reactions (2j − 2).
A symmetric triangular truss with a 6 m span and 1.5 m rise carries 8 kN at its apex on a pin and a roller. What is the force in each rafter?
B. 8.94 kN compression
Reactions 4 kN each. theta = arctan(1.5/3) = 26.57 degrees. Vertical equilibrium at the support: F_rafter = 4 / sin theta = 8.94 kN, pushing into the joint, so compression. 8.00 kN is the tie force; rafters of a gable truss under gravity load are always in compression.
A plane truss on a pin and a roller has 6 joints and 10 members. It is:
C. Internally indeterminate with one redundant member
2j - 3 = 9. With m = 10 there is one member more than needed, so member forces cannot be found by statics alone; the truss is indeterminate to the first degree.
For the same cross-sectional area of steel, why does an I-section or box-section chassis rail resist bending far better than a solid square bar?
B. It places more of its area far from the neutral axis, greatly raising the second moment of area
Second moment of area weights each element by the square of its distance from the axis (the A d^2 terms). Moving material into flanges far from the neutral axis raises I, and so bending stiffness and strength, without adding steel.
A 3000 kg tractor takes a level curve of 15 m radius at 5 m/s. What total sideways friction force must the tyres supply?
B. 5.0 kN
Centripetal force = m v^2 / r = 3000 x 25 / 15 = 5000 N = 5.0 kN, supplied by tyre side friction. Using v instead of v^2 gives 1.0 kN; multiplying by g treats the mass as a weight. 0.39 kN reads 5 m/s as 5 km/h (1.389 m/s).
A worker drags a sledge of seed 50 m along level ground with a rope tension of 300 N inclined 30 degrees above the horizontal. How much work does the rope do?
C. 12.99 kJ
W = F s cos theta = 300 x 50 x cos 30 = 12990 J = 12.99 kJ. The vertical component does no work because the sledge does not move vertically; using sin 30 takes the wrong component. 15.00 kJ uses the full tension; 7.50 kJ uses sin 30; 8.66 kJ uses tan 30.
An ideal hydraulic jack has a pump piston of 20 mm diameter and a lifting ram of 80 mm diameter. What force on the pump piston supports 16 kN on the ram?
A. 1.0 kN
Equal pressure (or virtual work with equal displaced volume): F1 / A1 = F2 / A2, so F1 = 16 x (20/80)^2 = 16 / 16 = 1.0 kN. Using the diameter ratio instead of the area ratio gives 4 kN. 0.25 kN cubes the diameter ratio; 256 kN multiplies by the area ratio instead of dividing.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.