Nepal Engineering Council Registration Exam — Agricultural Engineering · Nepal · Nepal Engineering Council
Original practice questions written to the published syllabus · not past papersNepal Engineering Council Registration Exam — Agricultural Engineering is a licensing and registration exam run by Nepal Engineering Council, for candidates in Nepal.
Official site: nec.gov.np.
We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.
Soil as an engineering material: its phases, flow of water through it, compaction, consolidation, shear strength and stability.
Our 75 Nepal Engineering Council Registration Exam questions in this subject: 38 easy, 29 medium, 8 hard, across 11 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to Nepal Engineering Council Registration Exam and are not shown on any other exam's page.
A core cutter of internal volume 1000 cm³ is filled with soil of mass 1950 g. The water content is 15%. What is the dry density?
C. 1.696 g/cm³
Bulk density ρ = 1950/1000 = 1.950 g/cm³. Dry density ρd = ρ/(1 + w) = 1.950/1.15 = 1.696 g/cm³. Multiplying by (1 − w) gives 1.657, which is wrong because water content is referred to dry mass, not total mass. 2.242 multiplies by (1 + w) instead of dividing (1.950 × 1.15).
A contractor has 2000 kg of moist borrow soil at a water content of 8% and must raise it to 14% before compaction. How much water must be added?
A. 111 kg
Water content is referred to dry mass. Ms = 2000/1.08 = 1851.9 kg. Water to add = Ms × (0.14 − 0.08) = 1851.9 × 0.06 = 111 kg (about 111 litres). Taking 6% of the moist mass gives 120 kg, an over-estimate; 259 kg is the total water needed at 14%, not the amount to add. 280 kg is 14% of the moist mass (0.14 × 2000).
A fine-grained inorganic soil has a liquid limit of 45% and a plasticity index of 22%. What is its group symbol in the Indian Standard system (IS 1498)?
D. CI
The A-line is Ip = 0.73(wL − 20) = 0.73 × 25 = 18.25. Ip = 22 lies above it, so the soil is a clay. IS 1498 uses three plasticity bands (L below 35, I from 35 to 50, H above 50), so wL = 45 gives CI. CL is the USCS symbol, which uses only L and H with the boundary at 50.
In a constant-head test, a sand specimen 150 mm long and 75 mm in diameter passes 500 mL of water in 120 s under a steady head difference of 400 mm. What is its coefficient of permeability?
B. 3.54e-04 m/s
A = π(75)²/4 = 4418 mm². k = QL/(Aht) = (500 × 10³ mm³ × 150)/(4418 × 400 × 120) = 0.3537 mm/s = 3.54e-04 m/s. Using A = πD² (forgetting /4) gives 8.84e-05; using the radius in πD²/4 gives 1.41e-03; 3.54e-03 is a unit slip.
In a flow net beneath a weir founded on a permeable layer over an impervious stratum, what is the surface of the impervious stratum?
B. A flow line
Water cannot cross an impervious boundary, so it flows along it: the boundary is a flow line. The upstream and downstream bed surfaces, where the head is fixed, are equipotential lines.
Two direct shear tests on the same soil give peak shear stresses of 75 kPa at a normal stress of 100 kPa and 125 kPa at a normal stress of 200 kPa. What are c and φ?
D. c = 25 kPa, φ = 26.6°
tanφ = (125 − 75)/(200 − 100) = 0.5, so φ = 26.6°. c = 75 − 100 × 0.5 = 25 kPa. Taking τ/σ from one test (0.75 → 36.9°) assumes c = 0 and ignores the second test.
What is Rankine's passive earth pressure coefficient for a cohesionless soil with φ = 36°?
A. 3.85
Kp = (1 + sinφ)/(1 − sinφ) = tan²(45° + φ/2) = tan²63° = 3.85. 0.26 is Ka; 1.96 forgets to square the tangent. 1.59 is the numerator 1 + sin 36° alone.
A long slope of dry cohesionless sand (φ′ = 32°) stands at 22° to the horizontal. What is the factor of safety against sliding on a plane parallel to the surface?
B. 1.55
For a dry cohesionless infinite slope F = tanφ′/tanβ = tan32°/tan22° = 0.6249/0.4040 = 1.55, independent of depth. The ratio of angles (1.45) is not the same as the ratio of tangents. 0.65 is the ratio inverted (tan 22°/tan 32°), and 1.41 uses sines (sin 32°/sin 22°).
A long sand slope (φ′ = 32°, c′ = 0, γsat = 20 kN/m³) stands at 22°. After heavy rain the water table rises to the surface and seepage is parallel to the slope. With γw = 9.81 kN/m³, what is the factor of safety?
A. 0.79
With parallel seepage and the water table at the surface, F = (γ′/γsat)·tanφ′/tanβ = (10.19/20) × 1.547 = 0.79. The dry-slope value 1.55 ignores pore pressure; seepage roughly halves F, and here the slope fails (F < 1). 3.04 inverts the weight ratio (20/10.19 × 1.547); 0.76 uses γw/γsat in place of γ′/γsat (9.81/20 × 1.547).
A square footing is founded at 1.5 m depth in saturated clay (cu = 40 kPa, φu = 0, γ = 19 kN/m³). Using Terzaghi's equation with Nc = 5.7 and a factor of safety of 3 on the net ultimate capacity, what is the gross safe bearing capacity?
C. 127.3 kPa
qu = 1.3cNc + γDf = 1.3 × 40 × 5.7 + 19 × 1.5 = 296.4 + 28.5 = 324.9 kPa. Net ultimate = 296.4 kPa. Net safe = 296.4/3 = 98.8 kPa. Gross safe = 98.8 + 28.5 = 127.3 kPa. Dividing the gross value by 3 (108.3) wrongly applies the factor of safety to the overburden as well; 104.5 forgets the 1.3 shape factor.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.