LAISHA
Open Laisha

Engineers Canada Agricultural / Biosystems / Bioresource / Food Engineering examination syllabus Soil Mechanics: practice questions

Engineers Canada Agricultural / Biosystems / Bioresource / Food Engineering examination syllabus · Canada · Provincial and territorial regulators (syllabus by Engineers Canada)

Original practice questions written to the published syllabus · not past papers
10worked here, free
26written to this exam in this subject
9syllabus units

About Engineers Canada Agricultural / Biosystems / Bioresource / Food Engineering examination syllabus

Engineers Canada Agricultural / Biosystems / Bioresource / Food Engineering examination syllabus is a licensing and registration exam run by Provincial and territorial regulators (syllabus by Engineers Canada), for candidates in Canada. Written confirmatory exams for graduates of non-CEAB programmes, assigned case by case.

Source: engineerscanada.ca.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Soil Mechanics in Engineers Canada Agricultural / Biosystems / Bioresource / Food Engineering examination syllabus

Soil as an engineering material: its phases, flow of water through it, compaction, consolidation, shear strength and stability.

Our 26 Engineers Canada Agricultural / Biosystems / Bioresource / Food Engineering examination syllabus questions in this subject: 13 easy, 11 medium, 2 hard, across 9 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Engineers Canada Agricultural / Biosystems / Bioresource / Food Engineering examination syllabus and are not shown on any other exam's page.

Question 1 · medium

A sand with 3% fines has D10 = 0.12 mm, D30 = 0.35 mm and D60 = 0.90 mm. What is its group symbol under the USCS (or IS 1498)?

  1. SP
  2. SW-SM
  3. GW
  4. SW
Answer and working

D. SW

Cu = D60/D10 = 0.90/0.12 = 7.5 (≥ 6) and Cc = D30²/(D10·D60) = 0.35²/(0.12 × 0.90) = 1.13 (between 1 and 3), so the sand is well graded. With fines under 5% no dual symbol is needed, so SW. A dual symbol such as SW-SM applies only for 5–12% fines.

Question 2 · easy

A clay has a liquid limit of 52%, a plastic limit of 24% and a natural water content of 31%. What is its liquidity index?

  1. 0.75
  2. 0.60
  3. 0.25
  4. 1.29
Answer and working

C. 0.25

Ip = 52 − 24 = 28. IL = (w − wP)/Ip = (31 − 24)/28 = 0.25; the clay is stiff, near its plastic limit. 0.75 is the consistency index Ic = (wL − w)/Ip, which equals 1 − IL. 0.60 is w/wL (31/52) and 1.29 is w/wP (31/24).

Question 3 · medium

A sand has 9% fines, Cu = 7 and Cc = 1.8. The fines plot above the A-line. What is its USCS group symbol?

  1. SW-SC
  2. SC
  3. SW
  4. SP-SC
Answer and working

A. SW-SC

Fines between 5 and 12% require a dual symbol. Cu ≥ 6 and 1 ≤ Cc ≤ 3 make it well graded (SW); clayey fines above the A-line add SC. SC alone needs more than 12% fines; SP would need the grading tests to fail.

Question 4 · medium

A permeability test at 30 °C gives k = 3.0 × 10⁻⁵ m/s. The viscosity of water is 0.798 mPa·s at 30 °C and 1.002 mPa·s at 20 °C. Ignoring the small change in unit weight, what is k corrected to 20 °C?

  1. 3.77e-05 m/s
  2. 3.00e-05 m/s
  3. 2.39e-05 m/s
  4. 2.00e-05 m/s
Answer and working

C. 2.39e-05 m/s

k is proportional to γw/μ, so k20 = k30 × μ30/μ20 = 3.0 × 10⁻⁵ × 0.798/1.002 = 2.39e-05 m/s. Water is more viscous at 20 °C, so the corrected k must be lower; the inverted ratio gives the wrong direction (3.77e-05).

Question 5 · easy

Which laboratory test is appropriate for measuring the permeability of a silty clay?

  1. Constant-head test
  2. Proctor compaction test
  3. Falling-head test
  4. Dry sieve analysis
Answer and working

C. Falling-head test

In fine-grained soils so little water passes that a constant-head test cannot measure the flow accurately; the falling-head test measures the fall in a narrow standpipe instead. The constant-head test suits sands and gravels.

Question 6 · medium

Taking the surface tension of water as 0.073 N/m, a contact angle of zero and γw = 9.81 kN/m³, what is the capillary rise in a clean glass tube of diameter 0.05 mm?

  1. 0.30 m
  2. 6.0 m
  3. 0.060 m
  4. 0.60 m
Answer and working

D. 0.60 m

hc = 4T cosα/(γw d) = 4 × 0.073/(9810 × 5 × 10⁻⁵) = 0.60 m (about 0.03/d with d in mm). Using 2T/(γw d), which is the formula with radius, but inserting the diameter, gives half the answer (0.30 m). 6.0 m and 0.060 m are decimal slips in converting 0.05 mm to metres (5 × 10⁻⁶ and 5 × 10⁻⁴ m).

Question 7 · hard

The water table is 2 m below ground in a silty clay that is fully saturated by capillarity up to the surface, with γsat = 19 kN/m³. With γw = 9.81 kN/m³, what is the vertical effective stress at 1 m depth?

  1. 9.19 kPa
  2. 19.00 kPa
  3. -0.62 kPa
  4. 28.81 kPa
Answer and working

D. 28.81 kPa

σ = 19 × 1 = 19 kPa. The point is 1 m above the water table, so u = −9.81 × 1 = −9.81 kPa (suction). σ′ = σ − u = 19 + 9.81 = 28.81 kPa. Treating the pore pressure as positive gives 9.19 kPa; ignoring it gives 19 kPa. Capillary suction increases effective stress. −0.62 kPa takes u as a positive 9.81 × 2 = 19.62 kPa from the full depth to the water table.

Question 8 · easy

According to Terzaghi's principle, which quantity controls the shear strength and volume change of a saturated soil?

  1. Effective stress (σ − u)
  2. Total stress (σ)
  3. Pore water pressure (u)
  4. Total stress plus pore water pressure (σ + u)
Answer and working

A. Effective stress (σ − u)

Only the stress carried by the grain skeleton, σ′ = σ − u, changes volume or strength. A rise in total stress carried entirely by the pore water produces no immediate change in either.

Question 9 · easy

For a soil with φ′ = 30°, at what angle to the major principal plane does the failure plane lie according to the Mohr-Coulomb criterion?

  1. 45°
  2. 60°
  3. 30°
  4. 75°
Answer and working

B. 60°

The failure plane is inclined at 45° + φ′/2 = 60° to the major principal plane. 45° is the plane of maximum shear stress, which is not the failure plane when φ′ > 0 because the normal stress on it is also higher. 30° is φ′ itself, and 75° adds φ′ instead of φ′/2 (45° + 30°).

Question 10 · medium

A sample of moist soil has a bulk density of 1.90 g/cm³ and a water content of 20%. The specific gravity of solids is 2.70. What is its void ratio?

  1. 0.705
  2. 0.421
  3. 0.540
  4. 0.414
Answer and working

A. 0.705

ρd = ρ/(1 + w) = 1.90/1.20 = 1.5833 g/cm³. e = Gρw/ρd − 1 = 2.70/1.5833 − 1 = 0.705. Using bulk density gives 0.421; wG = 0.540 is the void ratio only if the soil is saturated, which it is not here; 0.414 is the porosity e/(1 + e) = 0.705/1.705.

A study plan for Soil Mechanics in Engineers Canada Agricultural / Biosystems / Bioresource / Food Engineering examination syllabus

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (54% of the 26 questions): Index properties and soil classification (6, 23%); Effective stress (4, 15%); Permeability (4, 15%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Phase relations (4, 15%); Shear strength and the Mohr-Coulomb criterion (3, 12%); Compaction and the Proctor test (2, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Bearing capacity basics (1, 4%); Earth pressure: active and passive (Rankine) (1, 4%); Terzaghi one-dimensional consolidation (1, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Effective stress (1 hard of 4), Index properties and soil classification (1 hard of 6).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Compaction and the Proctor test (2 easy of 2); Bearing capacity basics (1 easy of 1).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Engineers Canada Agricultural / Biosystems / Bioresource / Food Engineering examination sy

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.