GATE — Agricultural Engineering (AG) · India · IITs and IISc on rotation (2027: IIT Madras)
Original practice questions written to the published syllabus · not past papersGATE — Agricultural Engineering (AG) is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks (15 General Aptitude + 85 technical: 25 one-mark and 30 two-mark questions). MCQ, MSQ and NAT; negative marking on MCQ only (−1/3 for one-mark, −2/3 for two-mark); no partial credit on MSQ. On-screen virtual calculator.
Source: gate2027.iitm.ac.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Numerical-answer and MCQ items: phase relations (e, n, S, γd from given masses and volumes), Atterberg indices, constant- and falling-head permeability, equivalent permeability of layered soils, seepage from flow nets and critical gradient, effective stress with a water table, Rankine active thrust with surcharge or water table, and the factor of safety of an infinite slope with and without seepage. Almost all require careful arithmetic and units.
Soil as an engineering material: its phases, flow of water through it, compaction, consolidation, shear strength and stability.
Our 100 GATE questions in this subject: 34 easy, 42 medium, 24 hard, across 11 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to GATE and are not shown on any other exam's page.
A soil has a bulk unit weight of 19.0 kN/m³, a water content of 12% and G = 2.65. Taking γw = 9.81 kN/m³, what is its degree of saturation?
B. 0.597
γd = γ/(1 + w) = 19.0/1.12 = 16.96 kN/m³. e = Gγw/γd − 1 = 2.65 × 9.81/16.96 − 1 = 0.532. S = wG/e = 0.12 × 2.65/0.532 = 0.597. Using the bulk instead of the dry unit weight to find e gives e = 0.368 and S = 0.864; 0.318 is just wG with no division by e.
A sand deposit has an in-situ void ratio of 0.62. Laboratory tests give a maximum void ratio of 0.85 and a minimum void ratio of 0.45. What is its relative density?
D. 57.5%
Dr = (emax − e)/(emax − emin) = (0.85 − 0.62)/(0.85 − 0.45) = 0.23/0.40 = 57.5%, a medium-dense sand. 42.5% comes from putting emin in the numerator, which measures looseness instead of density. 27.1% divides by emax alone (0.23/0.85), and 72.9% is e/emax (0.62/0.85).
In a hydrometer analysis, how long does a spherical particle of diameter 0.01 mm and specific gravity 2.65 take to settle 100 mm in water of viscosity 1.0 × 10⁻³ Pa·s (γw = 9.81 kN/m³)?
B. 18.5 min
Stokes' law: v = (γs − γw)D²/(18μ) = (2.65 − 1) × 9810 × (1.0 × 10⁻⁵)²/(18 × 10⁻³) = 8.993e-05 m/s. Time = 0.1/v = 1112 s = 18.5 min. Using γs instead of (γs − γw) ignores buoyancy and gives 11.5 min; the other options are factor-of-ten unit slips.
In a falling-head test, the standpipe area is 1.0 cm², the specimen is 10 cm long with an area of 50 cm², and the head falls from 100 cm to 50 cm in 600 s. What is k?
D. 2.31e-04 cm/s
k = (aL/(At))·ln(h1/h2) = (1.0 × 10)/(50 × 600) × ln 2 = 3.333e-04 × 0.693 = 2.31e-04 cm/s. Using log10 without the 2.303 factor gives 1.00e-04; swapping the standpipe and specimen areas gives an absurdly high 5.78e-01.
If the compactive effort applied to a soil is increased, how do its maximum dry density and optimum moisture content change?
D. Maximum dry density rises; optimum moisture content falls
More energy packs the grains more closely with less water needed for lubrication, so the curve moves up and to the left. This is why the modified Proctor test gives a higher maximum dry density at a lower optimum than the standard test.
A soil (G = 2.70) has a standard Proctor maximum dry unit weight of 17.5 kN/m³ at an optimum moisture content of 16%. With γw = 9.81 kN/m³, what is the percentage air voids at optimum?
C. 5.4%
e = Gγw/γd − 1 = 2.70 × 9.81/17.5 − 1 = 0.5135. S = wG/e = 0.16 × 2.70/0.5135 = 0.841. n = e/(1 + e) = 0.3393. na = n(1 − S) = 5.4%, within the few-per-cent range typical at optimum. 15.9% is air content (fraction of voids), not air voids (fraction of total volume). 8.2% uses e instead of n (0.5135 × 0.159); 84.1% is the degree of saturation.
Which assumption underlies Rankine's earth pressure theory?
D. The back of the wall is vertical and perfectly smooth
Rankine assumed a smooth vertical wall so that the stresses in a semi-infinite soil mass in plastic equilibrium apply directly. Wall friction is included in Coulomb's wedge theory; the log-spiral surface is used in more refined passive calculations.
What is the steepest slope angle for a long, dry cohesionless embankment face (φ′ = 35°) if a factor of safety of 1.5 is required?
C. 25.0°
F = tanφ′/tanβ, so tanβ = tan35°/1.5 = 0.4668 and β = 25.0°. Dividing the angle directly (35/1.5 = 23.3°) is not the same because tan is not linear. 35° gives F = 1. 46.4° multiplies tanφ′ by 1.5 instead of dividing.
A plate load test with a 0.3 m square plate on a deep, uniform dense sand gives an ultimate bearing pressure of 400 kPa. By the usual plate-load relation for sand, what is the ultimate bearing capacity of a 1.5 m square footing at the same level?
A. 2000 kPa
For sand the ultimate capacity from the γBNγ term is proportional to width: qf = qp × Bf/Bp = 400 × 1.5/0.3 = 2000 kPa. 400 kPa (no scaling) applies to clays, where capacity does not depend on width. The test reflects only soil within about twice the plate width, so deeper weak layers must be checked separately. 80 kPa inverts the width ratio (400 × 0.3/1.5), and 10000 kPa squares it (400 × 25).
How does compaction differ from consolidation?
D. Compaction expels air quickly by mechanical energy; consolidation slowly expels water from saturated soil under sustained load
Compaction is a rapid densification of partly saturated soil by rolling, tamping or vibration that reduces air voids. Consolidation is the gradual volume decrease of a saturated soil as pore water drains under a sustained load, governed by permeability.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.