LAISHA
Open Laisha

GATE Agricultural Drainage Engineering: practice questions

GATE — Agricultural Engineering (AG) · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
51written to this exam in this subject
11syllabus units

About GATE

GATE — Agricultural Engineering (AG) is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks (15 General Aptitude + 85 technical: 25 one-mark and 30 two-mark questions). MCQ, MSQ and NAT; negative marking on MCQ only (−1/3 for one-mark, −2/3 for two-mark); no partial credit on MSQ. On-screen virtual calculator.

Source: gate2027.iitm.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Agricultural Drainage Engineering in GATE

Numerical items in the Irrigation and Drainage section: drainage coefficient and discharge from an area, drainable porosity and water-table rise, drain pipe size, SAR from ion concentrations (including mg/L to meq/L), and leaching requirement and applied water depth. Hooghoudt spacing is in the syllabus but has been asked rarely; learn it, but weight the coefficient, porosity, SAR and LR items higher.

Removing excess water and salt: surface and subsurface drain design, and reclaiming saline and sodic land.

Our 51 GATE questions in this subject: 14 easy, 24 medium, 13 hard, across 11 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE and are not shown on any other exam's page.

Question 1 · easy

What is the main reason waterlogging of the root zone reduces the growth of most dryland crops?

  1. Oxygen supply to the roots is cut because gases diffuse very slowly through water-filled pores
  2. Roots absorb too many nutrients from the saturated soil and suffer from toxic overload
  3. The saturated soil becomes far warmer than the optimum temperature for root growth and respiration
  4. Evaporation from the wet surface dries the leaves
Answer and working

A. Oxygen supply to the roots is cut because gases diffuse very slowly through water-filled pores

Oxygen diffuses roughly 10,000 times more slowly in water than in air, so water-filled pores soon become anaerobic. Waterlogged soils are in fact cooler, not warmer, and nutrient uptake falls rather than rises.

Question 2 · hard

Before a canal was built the water table stood at 8 m depth. After irrigation began, net recharge to the groundwater increased by 60 mm/year. If the drainable porosity is 0.12, how many years until the water table reaches 2 m depth (assume no extra outflow)?

  1. 12 years
  2. 100 years
  3. 16 years
  4. 833 years
Answer and working

A. 12 years

Rise per year = recharge / drainable porosity = 0.060 / 0.12 = 0.50 m/year. The water table must rise 8 - 2 = 6 m, so t = 6 / 0.50 = 12 years. 100 years ignores the drainable porosity; 16 years uses 8 m instead of 6 m; 833 years multiplies instead of dividing by the porosity.

Question 3 · medium

In an arid irrigated area with negligible rain, 120 mm is applied every 12 days at 75 % application efficiency; all losses go to deep percolation. Canal seepage adds a further 0.5 mm/day to the groundwater. What subsurface drainage coefficient should be designed for?

  1. 3.0 mm/day
  2. 2.5 mm/day
  3. 8.0 mm/day
  4. 30.5 mm/day
Answer and working

A. 3.0 mm/day

Deep percolation = 120 x (1 - 0.75) = 30 mm per 12 days = 2.5 mm/day. Adding seepage: 3.0 mm/day. 2.5 forgets the seepage; 8.0 uses the stored fraction instead of the loss; 30.5 forgets to divide by the interval.

Question 4 · hard

The empirical van Beers relation gives drainable porosity (per cent) as the square root of hydraulic conductivity in cm/day. For K = 0.64 m/day, what drainable porosity does it give?

  1. 80 %
  2. 8 %
  3. 0.8 %
  4. 32 %
Answer and working

B. 8 %

Convert first: 0.64 m/day = 64 cm/day; sqrt(64) = 8 %, i.e. 0.08. Taking the root of 0.64 gives 0.8 (then 80 % if read as a fraction), which is impossible for a soil. The relation is approximate; measure drainable porosity where possible. 32 % halves 64 instead of taking its square root.

Question 5 · easy

Using the rational method, find the peak runoff from a 20 ha field with runoff coefficient 0.5 and design rainfall intensity 36 mm/h.

  1. 10 m3/s
  2. 0.1 m3/s
  3. 360 m3/s
  4. 1.0 m3/s
Answer and working

D. 1.0 m3/s

Q = CIA/360 = 0.5 x 36 x 20 / 360 = 1.0 m3/s with I in mm/h and A in ha. 360 forgets the unit-conversion constant; 10 and 0.1 are decimal slips.

Question 6 · medium

For the trapezoidal drain with bed width 1.0 m, depth 0.8 m, side slopes 1.5:1 carrying 0.69 m3/s, what is the mean velocity?

  1. 0.86 m/s
  2. 0.18 m/s
  3. 0.39 m/s
  4. 1.21 m/s
Answer and working

C. 0.39 m/s

V = Q/A = 0.69 / 1.76 = 0.39 m/s. Using the rectangle b x y = 0.8 m2 ignores the side triangles (0.69/0.8 = 0.86); dividing by the wetted perimeter of 3.88 m (0.18) or multiplying by the area (1.21) is dimensionally wrong. The velocity is then checked against the permissible non-erosive and non-silting limits for the soil.

Question 7 · medium

A surface drainage design module is 4 L/s per hectare. What drainage coefficient in mm/day is this?

  1. 3.46 mm/day
  2. 4.0 mm/day
  3. 14.4 mm/day
  4. 34.6 mm/day
Answer and working

D. 34.6 mm/day

4 L/s x 86,400 s = 345.6 m3/day per ha. Over 10,000 m2 that is 0.03456 m/day = 34.6 mm/day. 14.4 is the flow in m3/h per hectare (4 x 3,600 / 1,000), not a depth per day; 4.0 reads L/s per ha directly as mm/day; 3.46 is a decimal slip. A useful identity: 1 L/s/ha = 8.64 mm/day.

Question 8 · medium

In the USBR dynamic-equilibrium method, each irrigation adds 40 mm of deep percolation to a soil with drainable porosity 0.08. How much does each irrigation raise the water table?

  1. 0.50 m
  2. 3.2 mm
  3. 0.05 m
  4. 2.0 m
Answer and working

A. 0.50 m

Rise = R / mu = 0.040 / 0.08 = 0.50 m. 3.2 mm multiplies; 0.05 m is a decimal slip; 2.0 m divides porosity by recharge. At dynamic equilibrium this rise equals the fall achieved between irrigations.

Question 9 · medium

Irrigation water has EC 1.2 dS/m and the drainage water salinity must not exceed 8 dS/m. Using the US Salinity Laboratory formula, what is the leaching requirement?

  1. 15 %
  2. 6.67 %
  3. 85 %
  4. 1.5 %
Answer and working

A. 15 %

LR = ECiw / ECdw = 1.2 / 8 = 0.15 = 15 %. 85 % is 1 - LR; 6.67 is the inverse ratio; 1.5 % is a decimal slip.

Question 10 · easy

Using TDS (mg/L) = 640 x EC (dS/m), what is the approximate dissolved-salt content of water with EC 2.5 dS/m?

  1. 16,000 mg/L
  2. 160 mg/L
  3. 25 mg/L
  4. 1,600 mg/L
Answer and working

D. 1,600 mg/L

640 x 2.5 = 1,600 mg/L. 25 is roughly the total cations in meq/L (10 x EC), a different quantity. The factor 640 varies roughly 550-700 with composition. 16,000 and 160 mg/L are factor-of-ten slips.

A study plan for Agricultural Drainage Engineering in GATE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (49% of the 51 questions): Drainage coefficient (7, 14%); Irrigation water quality: EC, SAR and RSC (6, 12%); Salinity and the leaching requirement (6, 12%); Subsurface drain spacing: Hooghoudt and Ernst (6, 12%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Kirkham and Glover-Dumm equations (5, 10%); Reclamation of saline and sodic soils and gypsum requirement (5, 10%); Causes and effects of waterlogging (4, 8%); Surface drainage design (4, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Drain pipes and envelopes (3, 6%); Vertical drainage and bio-drainage (3, 6%); Interceptor and relief drains (2, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Vertical drainage and bio-drainage (2 hard of 3), Interceptor and relief drains (1 hard of 2), Reclamation of saline and sodic soils and gypsum requirement (2 hard of 5).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Causes and effects of waterlogging (2 easy of 4); Irrigation water quality: EC, SAR and RSC (2 easy of 6).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE Agricultural Drainage Engineering

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.