LAISHA
Open Laisha

GATE Sprinkler & Micro-Irrigation Systems: practice questions

GATE — Agricultural Engineering (AG) · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
65written to this exam in this subject
14syllabus units

About GATE

GATE — Agricultural Engineering (AG) is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks (15 General Aptitude + 85 technical: 25 one-mark and 30 two-mark questions). MCQ, MSQ and NAT; negative marking on MCQ only (−1/3 for one-mark, −2/3 for two-mark); no partial credit on MSQ. On-screen virtual calculator.

Source: gate2027.iitm.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Sprinkler & Micro-Irrigation Systems in GATE

Designing and evaluating sprinkler and drip systems, from emitter hydraulics to pump selection.

Our 65 GATE questions in this subject: 28 easy, 32 medium, 5 hard, across 14 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE and are not shown on any other exam's page.

Question 1 · medium

A sprinkler nozzle of 5 mm diameter with discharge coefficient 0.95 operates at 300 kPa. What is its discharge? (g = 9.81 m/s², ρ = 1000 kg/m³)

  1. 1.431 L/s
  2. 1.828 L/s
  3. 0.457 L/s
  4. 0.481 L/s
Answer and working

C. 0.457 L/s

Head h = 300 000/(1000 × 9.81) = 30.58 m. Area a = π/4 × 0.005² = 1.963e-05 m². q = Cd a √(2gh) = 0.95 × 1.963e-05 × √(2 × 9.81 × 30.58) = 4.569e-04 m³/s = 0.457 L/s. Using 300 directly as metres of head gives 1.431 L/s; using the diameter as a radius gives 1.828 L/s; omitting Cd gives 0.481 L/s.

Question 2 · medium

Eight catch cans between sprinklers collect 10, 12, 9, 11, 8, 12, 10 and 8 mm. What is Christiansen's uniformity coefficient?

  1. 80.0 %
  2. 12.5 %
  3. 85.0 %
  4. 87.5 %
Answer and working

D. 87.5 %

Mean = 80/8 = 10 mm. Absolute deviations 0, 2, 1, 1, 2, 2, 0, 2 sum to 10 mm. CU = 100 (1 − 10/(8 × 10)) = 87.5 %. 80 % is the low-quarter DU; 85.0 % uses the standard deviation (a different coefficient). 12.5 % is the deviation ratio 10/80 itself, not 100 (1 − 10/80).

Question 3 · medium

Twelve catch cans record (mm): 14, 18, 16, 12, 20, 15, 17, 16, 13, 19, 15, 17. What is Christiansen's CU?

  1. 81.2 %
  2. 85.8 %
  3. 88.5 %
  4. 75.0 %
Answer and working

C. 88.5 %

Mean = 192/12 = 16 mm. Σ|xi − x̄| = 22 mm. CU = 100 (1 − 22/(12 × 16)) = 88.5 %. 81.25 % is the low-quarter DU; 75 % is the minimum-to-mean ratio; 85.8 % uses the standard deviation instead of the mean absolute deviation.

Question 4 · medium

As the number of outlets on a lateral becomes very large, the F factor for the Darcy-Weisbach equation (m = 2) tends to:

  1. 1/2
  2. 0.351
  3. 1
  4. 1/3
Answer and working

D. 1/3

F → 1/(m+1) = 1/3 for m = 2. 0.351 is the limit for Hazen-Williams (m = 1.852); 1 applies to a pipe with a single outlet at the end.

Question 5 · medium

Why do labyrinth (tortuous-path) emitters allow a larger flow passage than long-path laminar emitters for the same discharge?

  1. The labyrinth acts as a filter
  2. They operate at much higher pressure
  3. The labyrinth stores water between pulses, so each pulse can leave through a wider outlet
  4. The zigzag path creates turbulence that dissipates head in a shorter, wider channel
Answer and working

D. The zigzag path creates turbulence that dissipates head in a shorter, wider channel

In a tortuous path, repeated changes of direction dissipate energy through turbulence, so a wider, shorter channel achieves the same head loss; this reduces clogging risk and makes x close to 0.5. A long laminar path needs a very narrow, long channel.

Question 6 · easy

In an older drip system that was designed with a high emission uniformity, what is usually the main reason field EU has fallen?

  1. Increase in the emitter exponent with age
  2. Higher water viscosity
  3. Emitter clogging
  4. Reduced wetted diameter of the soil
Answer and working

C. Emitter clogging

Physical, chemical and biological clogging reduces flow unevenly and is the dominant cause of declining uniformity. Water treatment, filtration and flushing are the remedies.

Question 7 · medium

5 kg N/ha is to be applied to 4 ha as urea (46 % N) dissolved at 0.3 kg urea per litre of stock solution and injected over 2 hours. What is the injection rate?

  1. 33.3 L/h
  2. 72.5 L/h
  3. 145 L/h
  4. 66.7 L/h
Answer and working

B. 72.5 L/h

N = 5 × 4 = 20 kg; urea = 20/0.46 = 43.5 kg; stock volume = 43.5/0.3 = 145 L; injection rate = 145/2 = 72.5 L/h. Forgetting to convert N to urea gives 33.3 L/h; forgetting the injection time gives 145 L/h. 66.7 L/h forgets both the urea conversion and the 2-hour injection time (20/0.3).

Question 8 · easy

Which pair of fertilisers must not be mixed in the same concentrated stock tank because a precipitate forms?

  1. Urea and potassium nitrate
  2. Potassium chloride and urea, which react to release ammonia gas
  3. Calcium nitrate and a sulphate or phosphate fertiliser
  4. Ammonium nitrate and urea
Answer and working

C. Calcium nitrate and a sulphate or phosphate fertiliser

Calcium reacts with sulphate to form gypsum and with phosphate to form calcium phosphates, both of low solubility; they are kept in separate A and B tanks. The other pairs are compatible in normal stock concentrations.

Question 9 · medium

A drip system has static lift 20 m, well drawdown 3 m, mainline friction 4 m, filter loss 5 m (dirty limit), injector loss 2 m, required sub-main inlet pressure 15 m and a 2 m rise to the critical block. What is the total dynamic head?

  1. 51 m
  2. 48 m
  3. 49 m
  4. 36 m
Answer and working

A. 51 m

TDH = 20 + 3 + 4 + 5 + 2 + 15 + 2 = 51 m. Omitting drawdown gives 48 m, omitting the elevation rise gives 49 m, and omitting the required operating pressure gives 36 m, all of which would leave the critical block under-pressured.

Question 10 · easy

When dividing a drip field into irrigation shifts (zones), what is the main hydraulic aim?

  1. Shifts of equal area, usually regardless of crop
  2. Shifts of about equal flow so the pump always runs near its design point
  3. As many shifts as possible to lower pipe cost
  4. One shift per crop row
Answer and working

B. Shifts of about equal flow so the pump always runs near its design point

Equal-flow shifts keep the pump at the same operating point and efficiency for every shift. Equal area is not enough when crops or emitter densities differ.

A study plan for Sprinkler & Micro-Irrigation Systems in GATE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (45% of the 65 questions): Sprinkler types and components (7, 11%); Christiansen's uniformity coefficient (6, 9%); Sprinkler spacing and application rate (6, 9%); Allowable pressure variation and the friction factor F (5, 8%); Drip system components (5, 8%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Economics of pressurised irrigation (5, 8%); Fertigation (5, 8%); Sprinkler lateral and main design (5, 8%); Drip lateral and sub-main design (4, 6%); Emitter hydraulics: exponent and coefficient of variation (4, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Filtration (4, 6%); System layout and pump selection (4, 6%); Automation (3, 5%); Emission uniformity (2, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Drip lateral and sub-main design (1 hard of 4), Allowable pressure variation and the friction factor F (1 hard of 5), Sprinkler lateral and main design (1 hard of 5).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Automation (2 easy of 3); Drip system components (3 easy of 5).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE Sprinkler & Micro-Irrigation Systems

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.