LAISHA
Open Laisha

GATE Tractor Systems & Controls: practice questions

GATE — Agricultural Engineering (AG) · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
65written to this exam in this subject
15syllabus units

About GATE

GATE — Agricultural Engineering (AG) is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks (15 General Aptitude + 85 technical: 25 one-mark and 30 two-mark questions). MCQ, MSQ and NAT; negative marking on MCQ only (−1/3 for one-mark, −2/3 for two-mark); no partial credit on MSQ. On-screen virtual calculator.

Source: gate2027.iitm.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Tractor Systems & Controls in GATE

Section 3 'Tractors and Power Tillers': numerical questions on overall gear ratio and travel speed, differential speeds, clutch torque capacity (uniform wear vs uniform pressure), PTO speed and power, Ackermann steering angles, and hydraulic force and power; conceptual MCQ/MSQ on gearbox types, draft vs position control, open vs closed centre hydraulics. NAT answers are sensitive to radius vs diameter and rev/min vs rev/s.

Everything between the engine and the implement: clutch, gearbox, differential, PTO, brakes, steering, hydraulics, hitch and tyres.

Our 65 GATE questions in this subject: 22 easy, 29 medium, 14 hard, across 15 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE and are not shown on any other exam's page.

Question 1 · easy

In a two-stage reduction, a 15-tooth pinion on the input shaft drives a 45-tooth gear on the countershaft, and a 12-tooth pinion on the countershaft drives a 48-tooth gear on the output shaft. If the input turns at 1,800 rev/min, the output speed is

  1. 257 rev/min
  2. 600 rev/min
  3. 21,600 rev/min
  4. 150 rev/min
Answer and working

D. 150 rev/min

Ratio = (45/15) × (48/12) = 3 × 4 = 12. Output = 1,800/12 = 150 rev/min. Adding the ratios (3 + 4 = 7) gives 257; using only the first stage gives 600; multiplying instead of dividing gives 21,600.

Question 2 · medium

A single-plate clutch has linings of outer radius 150 mm and inner radius 100 mm, μ = 0.3, and spring force 4000 N. Assuming uniform wear, the torque capacity is

  1. 304 N·m
  2. 150 N·m
  3. 300 N·m
  4. 360 N·m
Answer and working

C. 300 N·m

Uniform wear: R_m = (R_o + R_i)/2 = 0.125 m. T = μ W n R_m = 0.3 × 4000 × 2 × 0.125 = 300 N·m (n = 2 because the single driven plate has two friction faces). Uniform pressure gives R_m = 0.1267 m and 304 N·m; n = 1 gives 150 N·m; using the outer radius gives 360 N·m.

Question 3 · hard

A tractor engine develops a maximum torque of 250 N·m. The single-plate dry clutch must carry 1.4 times this torque. Linings: outer radius 140 mm, inner radius 90 mm, μ = 0.35. Using the uniform-wear assumption, the total spring force needed is closest to

  1. 4,348 N
  2. 8,696 N
  3. 3,106 N
  4. 3,571 N
Answer and working

A. 4,348 N

Design torque = 250 × 1.4 = 350 N·m. R_m = (0.14 + 0.09)/2 = 0.115 m. W = T/(μ n R_m) = 350/(0.35 × 2 × 0.115) = 4,348 N. Using one friction face doubles it to 8,696 N; ignoring the service factor gives 3,106 N, a clutch that slips at peak load; using the outer radius gives 3,571 N.

Question 4 · medium

An operator holds a tractor's open-centre hydraulic lever against the stop after the cylinder has reached the end of its stroke. The gear pump delivers 30 L/min and the relief valve is set at 17.5 MPa. The rate of heat generation in the oil is

  1. 0.875 kW
  2. zero, because the cylinder is not moving
  3. 525 kW
  4. 8.75 kW
Answer and working

D. 8.75 kW

All the flow passes over the relief valve and does no work, so heat = Δp × Q = 17.5 MPa × 30 L/min/60 = 8.75 kW. /600 applies to bar, not MPa. This is why levers must not be held against the relief valve and why open-centre systems overheat when misused.

Question 5 · hard

A 2WD tractor must develop a net pull of 18 kN on a soil where the usable net traction ratio at acceptable slip is 0.45. The dynamic load on the rear wheels is at present 32 kN. The ballast to add over the rear wheels is about

  1. 4,077 kg
  2. 1,835 kg
  3. 8,000 kg
  4. 815 kg
Answer and working

D. 815 kg

Required rear load = pull/ratio = 18.0/0.45 = 40 kN. Extra load = 40 − 32 = 8 kN = 8,000 N ÷ 9.81 = 815 kg. 4,077 kg is the whole rear load, not the addition; 8,000 forgets to convert newtons to kilograms. Check slip in the field afterwards, because the traction ratio varies with soil. 1,835 kg converts the whole 18 kN pull to mass (18,000/9.81).

Question 6 · medium

The synchroniser in a synchromesh gearbox

  1. locks the differential when the gear lever is moved to low range
  2. uses a cone clutch to match speeds before the dogs engage
  3. slides the spur gear sideways along its splines into mesh with the layshaft gear
  4. reverses the output direction by inserting an idler between the shafts
Answer and working

B. uses a cone clutch to match speeds before the dogs engage

The synchro ring rubs on the gear cone to bring both to the same speed, then the collar's dogs engage without clash, allowing shifts on the move.

Question 7 · medium

A 35 mm PTO shaft with 21 splines is designed to run at

  1. 1,000 rev/min
  2. 540 rev/min (type 1)
  3. 540 rev/min economy mode
  4. Proportional to ground speed
Answer and working

A. 1,000 rev/min

Type 1 is 35 mm with 6 splines at 540 rev/min; type 2 is 35 mm with 21 splines at 1,000 rev/min; type 3 is 45 mm with 20 splines at 1,000 rev/min. Different splines prevent mismatching.

Question 8 · easy

The recirculating-ball steering gear uses balls

  1. as the main bearing of the front wheel
  2. to lock the differential
  3. running between a worm and a nut to reduce friction
  4. in the power-steering pump
Answer and working

C. running between a worm and a nut to reduce friction

Steel balls roll in the grooves between the worm and nut and recirculate through a return tube, giving low friction and wear.

Question 9 · medium

Rear drive tyres with chevron lugs should be mounted so that

  1. the open end of the chevron contacts the ground first, so mud is squeezed out
  2. the point of the chevron contacts the ground first as the wheel rolls forward
  3. direction does not matter
  4. the lugs point towards the tractor centre
Answer and working

B. the point of the chevron contacts the ground first as the wheel rolls forward

Mounted correctly the lugs dig in and self-clean; mounted backwards they pack with soil and lose traction.

Question 10 · hard

If an MFWD tractor is fitted with front tyres of a smaller rolling circumference than specified, the likely result is

  1. better traction with no drawback, as smaller front tyres dig in harder under the drive torque
  2. higher road speed
  3. the front wheels lag the rear, causing tyre scrub, power circulation and drive-train wear
  4. lighter steering
Answer and working

C. the front wheels lag the rear, causing tyre scrub, power circulation and drive-train wear

The front axle ratio is set for a small lead with the specified tyres. Smaller front tyres reduce or reverse the lead, so the axles fight each other.

A study plan for Tractor Systems & Controls in GATE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (49% of the 65 questions): Hydraulic system: open and closed centre (8, 12%); Power take-off: standards and speeds (8, 12%); Steering geometry (Ackermann) and power steering (6, 9%); Clutch: single and dual plate (5, 8%); CVT and power-shift transmissions (5, 8%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Gearbox and transmission: sliding, constant and synchromesh (5, 8%); Brakes (4, 6%); Differential and differential lock (4, 6%); Final drive (4, 6%); Tyres and ballasting (4, 6%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Three-point hitch: categories, free and restrained links (3, 5%); Tractor types and selection (3, 5%); Draft and position control (2, 3%); Operator controls and ROPS (2, 3%); Power tillers (2, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Tyres and ballasting (2 hard of 4), Power tillers (1 hard of 2), Steering geometry (Ackermann) and power steering (2 hard of 6).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Tractor types and selection (2 easy of 3); Differential and differential lock (2 easy of 4).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE Tractor Systems & Controls

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.