ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR
Original practice questions written to the published syllabus · not past papersICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.
Source: icar.org.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Unit V farm power: identification of transmission components and their functions, PTO standards, hitch categories, brakes and steering types, hydraulic control modes, power tillers; mostly recall with short calculations.
Everything between the engine and the implement: clutch, gearbox, differential, PTO, brakes, steering, hydraulics, hitch and tyres.
Our 54 ICAR AIEEA-PG questions in this subject: 24 easy, 30 medium, 0 hard, across 15 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.
A PTO dynamometer reads 250 N·m at 540 rev/min. The PTO power is
D. 14.14 kW
P = 2πNT/60,000 = 2π × 540 × 250/60,000 = 14.14 kW. Leaving out 2π gives 2.25; assuming a 1,000 rev/min shaft gives 26.18; not dividing rev/min by 60 gives a value sixty times too large.
A power tiller engine runs at 2200 rev/min; the overall reduction to the wheels is 60:1 and the pneumatic wheel diameter is 0.6 m. The theoretical forward speed is
A. 4.15 km/h
Wheel speed = 2200/60 = 36.67 rev/min. v = πDN = π × 0.6 × 36.67 = 69.1 m/min = 4.15 km/h. Treating 0.6 m as a radius doubles it; 1.15 is in m/s; 69.1 is m/min mislabelled.
Which tractor type steers by hinging the frame between the front and rear axles?
C. Articulated four-wheel-drive tractor
Articulated 4WD tractors have equal-size wheels on rigid axles and steer by a central hinge with hydraulic cylinders. The others use steered front wheels.
A row-crop tractor differs from a general utility tractor mainly in having
B. high crop clearance and adjustable track width to straddle crop rows
Row-crop tractors are built to work between and over crop rows: high clearance and adjustable wheel track. Low and narrow build is the orchard tractor.
In a dual (two-stage) clutch, pressing the pedal half way
A. stops drive to the transmission while the PTO keeps running
The first stage of pedal travel releases the transmission clutch; full travel also releases the PTO clutch. That is what makes the PTO 'live'.
Constant-mesh gearboxes can use helical gears while sliding-mesh gearboxes normally use spur gears because
C. helical gears are hard to slide into mesh, but in constant mesh they never need to be
Helical teeth produce axial thrust and cannot be slid into engagement easily; in constant mesh the gears stay meshed and dog clutches do the selecting, so quieter, stronger helical gears can be used.
The standard rear PTO speeds defined by ISO 500 for field tractors are
B. 540 and 1,000 rev/min
ISO 500 (harmonised with ASABE S203/S205) defines 540 rev/min (type 1) and 1,000 rev/min (types 2 and 3 and larger) shafts.
Caster in front-wheel geometry is
B. the fore-and-aft tilt of the kingpin axis, giving a self-centring effect
Caster tilts the steering axis back so the contact patch trails it, like a trolley wheel. The other options describe camber, toe-in and kingpin inclination.
Float setting on a tractor hitch allows the implement to
D. follow the ground contour on its own gauge wheels or skids
In float the lift is free, so the implement rides on its own wheels or skids and follows the ground.
A rollover protective structure (ROPS) protects the operator only if
A. the seat belt is worn so the operator stays within the protective zone
In an overturn an unbelted operator can be thrown out and crushed by the tractor or the ROPS itself. Belt and ROPS work together.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.