LAISHA
Open Laisha

ICAR AIEEA-PG Engineering Properties of Agricultural Produce: practice questions

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
67written to this exam in this subject
10syllabus units

About ICAR AIEEA-PG

ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) is a postgraduate admission exam run by National Testing Agency for ICAR, for candidates in India. Computer-based, 120 minutes, 120 MCQs, +4 / −1, English only (2026 bulletin). One paper for the whole subject group.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Engineering Properties of Agricultural Produce in ICAR AIEEA-PG

Unit VI (biological materials) asks one-step MCQs: definitions of sphericity, roundness, porosity, angle of repose and terminal velocity; the meaning of n in the power law; which model describes stress relaxation or creep; units of thermal diffusivity; and sorption-isotherm vocabulary such as hysteresis and monolayer moisture.

The physical, frictional, aerodynamic, thermal, rheological and electrical properties of grains, fruits and foods that every machine and process is designed around.

Our 67 ICAR AIEEA-PG questions in this subject: 33 easy, 27 medium, 7 hard, across 10 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AIEEA-PG and are not shown on any other exam's page.

Question 1 · medium

A maize kernel has length 8.4 mm, width 5.6 mm and thickness 3.9 mm. Using Mohsenin's definition of sphericity, Φ = (LWT)^(1/3) / L, the sphericity is

  1. 0.68
  2. 0.71
  3. 0.67
  4. 1.01
Answer and working

A. 0.68

D_g = (8.4 × 5.6 × 3.9)^(1/3) = 5.68 mm, so Φ = 5.68 / 8.4 = 0.68. 0.71 uses the arithmetic mean diameter (5.97 mm) instead of the geometric mean; 0.67 is the aspect ratio W/L; 1.01 divides by the width instead of the major diameter.

Question 2 · medium

A potato tuber weighs 220 g in air and 18 g when suspended fully submerged in water. Taking the specific gravity of water as 1.000, the specific gravity of the tuber is

  1. 12.222
  2. 1.089
  3. 0.918
  4. 1.082
Answer and working

B. 1.089

SG = weight in air / (weight in air − weight in water) = 220 / (220 − 18) = 220 / 202 = 1.089. 220/18 treats the submerged weight as the displaced water; 202/220 inverts the ratio; 238/220 adds instead of subtracting the buoyant loss. These give 12.222, 0.918 and 1.082 respectively.

Question 3 · easy

A grain bulk has a porosity of 0.40. Its void ratio, e = ε / (1 − ε), is

  1. 0.400
  2. 0.600
  3. 0.667
  4. 1.500
Answer and working

C. 0.667

e = 0.40 / 0.60 = 0.667. 0.400 repeats the porosity; 0.600 is the solid fraction 1 − ε; 1.500 is (1 − ε)/ε, the inverse of the void ratio.

Question 4 · easy

At the same superficial airflow rate per unit floor area, which bed of grain will show the greatest pressure drop per metre of depth?

  1. A bed of large kernels such as maize or soybean
  2. A bed of small seeds such as millet
  3. A bed of whole groundnut pods with shells intact
  4. All beds give the same drop at equal airflow rate
Answer and working

B. A bed of small seeds such as millet

Smaller particles give smaller voids and larger specific surface, so resistance rises sharply; airflow-resistance data in the ASABE standard show much higher pressure drop for small seeds than for maize or soybean. Pods with shells pack loosely and resist airflow least. Pressure drop depends on the crop, which is why the standard gives separate constants for each.

Question 5 · easy

In the Stokes (creeping-flow) regime, the drag coefficient of a sphere varies with Reynolds number as

  1. C_d = 24/Re
  2. C_d = 0.44
  3. C_d = 64/Re
  4. C_d = 24·Re
Answer and working

A. C_d = 24/Re

Stokes' solution gives F = 3π μ d V, which corresponds to C_d = 24/Re. A constant 0.44 belongs to the Newton regime; 64/Re is the laminar pipe-flow friction factor; drag coefficient falls, not rises, with Re in this regime.

Question 6 · easy

Siebel's equation for frozen food is c = 0.837 + 1.256 X_w (kJ/kg·K). For frozen fish with 75% moisture (wet basis), c is

  1. 3.35 kJ/kg·K
  2. 0.94 kJ/kg·K
  3. 1.78 kJ/kg·K
  4. 1.57 kJ/kg·K
Answer and working

C. 1.78 kJ/kg·K

c = 0.837 + 1.256 × 0.75 = 1.779 kJ/kg·K. 3.35 applies the unfrozen equation; 0.94 drops the solids term; 1.57 counts only ice at about 2.09 kJ/kg·K and ignores the solids.

Question 7 · hard

A steel ball of radius 1.0 mm (density 7800 kg/m³) falls at a steady 8.0 mm/s through honey (density 1400 kg/m³). Using Stokes' law, μ = 2r²g(ρ_s − ρ_f)/(9v), the viscosity of the honey is

  1. 1.74 Pa·s
  2. 6.98 Pa·s
  3. 2.13 Pa·s
  4. 0.436 Pa·s
Answer and working

A. 1.74 Pa·s

μ = 2 × (10⁻³)² × 9.81 × 6400 / (9 × 0.008) = 0.12557/0.072 = 1.74 Pa·s. 6.98 uses the diameter in r²; 2.13 ignores the buoyancy of the honey; 0.436 treats 1.0 mm as the diameter and halves it again.

Question 8 · easy

A Kelvin-Voigt element (spring and dashpot in parallel) loaded with a constant stress shows

  1. instantaneous strain followed by unlimited steady flow at constant rate, as in a viscous liquid
  2. delayed creep towards σ0/E, with no instantaneous strain and no stress relaxation
  3. exponential stress relaxation to zero under a constant applied strain
  4. instantaneous elastic strain only, with no time-dependent deformation
Answer and working

B. delayed creep towards σ0/E, with no instantaneous strain and no stress relaxation

In parallel, the dashpot prevents instantaneous deformation and the spring limits the final strain to σ0/E, so strain rises as 1 − e^(−t/λ). Instantaneous strain plus unlimited flow is Maxwell behaviour; stress relaxation to zero is also Maxwell; purely instantaneous strain is a Hookean spring.

Question 9 · easy

Non-enzymatic (Maillard) browning in dried foods is fastest at

  1. water activity below the monolayer
  2. intermediate water activity, near 0.6–0.8
  3. water activity of exactly 1.0
  4. water activity near zero
Answer and working

B. intermediate water activity, near 0.6–0.8

Browning needs reactant mobility but slows when reactants are diluted, so it peaks at intermediate a_w. Below the monolayer reactants are immobile; at a_w near 1 they are diluted; near zero there is too little water for the reaction to proceed readily.

Question 10 · easy

Moisture content on dry basis is preferred in drying calculations because

  1. dry-basis values never exceed 100%, which keeps every drying curve on a bounded and convenient scale
  2. grain trade standards worldwide quote moisture only on a dry basis
  3. wet-basis moisture cannot be measured by the air-oven method
  4. the mass of dry matter stays constant while water is removed, so changes are on a fixed base
Answer and working

D. the mass of dry matter stays constant while water is removed, so changes are on a fixed base

Dry matter is conserved during drying, so dry-basis moisture changes linearly with water lost. Dry-basis values can exceed 100% (wet basis cannot); trade normally uses wet basis; the oven method gives both bases from the same weighings.

A study plan for Engineering Properties of Agricultural Produce in ICAR AIEEA-PG

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (49% of the 67 questions): Size and shape: sphericity and roundness (9, 13%); Water activity (9, 13%); Rheology: Newtonian and non-Newtonian flow (8, 12%); Porosity (7, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Thermal properties: specific heat, conductivity and diffusivity (7, 10%); Volume and density: bulk and true (7, 10%); Aerodynamic properties: terminal velocity (6, 9%); Frictional properties: angle of repose and coefficient of friction (6, 9%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Electrical and optical properties (4, 6%); Viscoelastic models (4, 6%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Rheology: Newtonian and non-Newtonian flow (3 hard of 8), Viscoelastic models (1 hard of 4), Porosity (1 hard of 7).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Viscoelastic models (3 easy of 4); Thermal properties: specific heat, conductivity and diffusivity (5 easy of 7).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AIEEA-PG Engineering Properties of Agricultural Produce

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.