LAISHA
Open Laisha

ICAR AICE-JRF/SRF Engineering Properties of Agricultural Produce: practice questions

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
57written to this exam in this subject
10syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Engineering Properties of Agricultural Produce in ICAR AICE-JRF/SRF

Unit 1 at PG depth: Hertz contact and the bioyield point, Burgers and generalised Maxwell models, Peleg relaxation, dynamic moduli and tan δ, Rabinowitsch-Mooney correction, Metzner-Reed Reynolds number, Choi-Okos and Sweat models, line heat source theory, GAB and BET fitting, isosteric heat, dielectric loss and penetration depth.

The physical, frictional, aerodynamic, thermal, rheological and electrical properties of grains, fruits and foods that every machine and process is designed around.

Our 57 ICAR AICE-JRF/SRF questions in this subject: 5 easy, 24 medium, 28 hard, across 10 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · hard

A sieve analysis of ground feed (ASABE method) leaves 40 g, 35 g and 25 g on three sieves whose geometric mean apertures d̄_i are 1.0 mm, 0.5 mm and 0.25 mm. The mass-weighted geometric mean diameter, d_gw = antilog[Σ(W_i log d̄_i) / ΣW_i], is

  1. 0.555 mm
  2. 0.637 mm
  3. 0.500 mm
  4. 0.196 mm
Answer and working

A. 0.555 mm

Σ W log d̄ = 40(0) + 35(−0.30103) + 25(−0.60206) = −25.588; dividing by 100 g gives −0.25588, and antilog gives 0.555 mm. 0.637 mm is the arithmetic mass-weighted mean, which overstates the size of a log-normally distributed grind; 0.500 mm is the unweighted geometric mean of the three apertures, ignoring the masses; 0.196 is a logarithm mistaken for a diameter.

Question 2 · hard

An air-comparison pycnometer has two chambers of equal volume. Chamber 1 (empty) is charged to 150 kPa gauge; chamber 2, packed with grain, is at 0 kPa gauge. After the valve is opened the pressure settles at 107 kPa gauge. Assuming isothermal expansion, so that porosity ε = (P1 − P2)/P2 with gauge pressures, the porosity of the grain is

  1. 0.402
  2. 0.287
  3. 0.713
  4. 0.167
Answer and working

A. 0.402

Boyle's law in gauge terms gives P1 V = P2 (V + V_v), so V_v/V = (P1 − P2)/P2 = 43/107 = 0.402. Dividing by P1 gives 0.287; 0.713 is just the pressure ratio; 0.167 divides by the sum, which has no basis in the derivation.

Question 3 · hard

Using Janssen's equation, the lateral pressure on the wall of a deep bin approaches L_max = ρ_b g R / μ', where R is the hydraulic radius (area/perimeter). For a 6.0 m diameter bin storing grain of bulk density 780 kg/m³ with a wall friction coefficient μ' = 0.40, L_max is

  1. 57.4 kPa
  2. 4.6 kPa
  3. 114.8 kPa
  4. 28.7 kPa
Answer and working

D. 28.7 kPa

For a circle R = A/P = (πD²/4)/(πD) = D/4 = 1.5 m, so L_max = 780 × 9.81 × 1.5 / 0.40 = 28694 Pa = 28.7 kPa. 57.4 kPa takes R as the radius D/2; 4.6 kPa multiplies by μ' instead of dividing; 114.8 kPa uses the diameter.

Question 4 · medium

For spheres of the same density in air, doubling the diameter changes the terminal velocity by a factor of

  1. 4 in the Newton regime and √2 in the Stokes regime
  2. 2 in both regimes, since terminal velocity scales with diameter
  3. √2 in the Newton regime and 4 in the Stokes regime
  4. 1 in both regimes, since density alone sets terminal velocity
Answer and working

C. √2 in the Newton regime and 4 in the Stokes regime

In the Newton regime V_t ∝ (d)^(1/2), so doubling d gives √2 = 1.41; in the Stokes regime V_t ∝ d², giving 4. Swapping the two is the common slip. Terminal velocity does depend on size, so neither 2 nor 1 is right.

Question 5 · medium

Creep and recovery of a potato tissue sample show an instantaneous strain, a delayed elastic strain, a steady flow and a permanent set after the load is removed. The simplest spring-dashpot model that reproduces all four is

  1. the two-element Maxwell model, a single spring and a single dashpot connected in series
  2. the two-element Kelvin-Voigt model, a single spring and a single dashpot connected in parallel
  3. the three-element standard linear solid, a spring in parallel with a Maxwell element
  4. the four-element Burgers model
Answer and working

D. the four-element Burgers model

Burgers' free spring gives instantaneous strain, its Kelvin element the delayed elastic strain, and its free dashpot the steady flow that remains as permanent set. Maxwell lacks delayed elasticity; Kelvin lacks instantaneous strain and flow; the standard linear solid has no unbounded flow, so it shows no permanent set. The Burgers model is a Maxwell element in series with a Kelvin-Voigt element.

Question 6 · hard

A Burgers model has E1 = 400 kPa, η1 = 8000 kPa·s (Maxwell part) and E2 = 200 kPa, η2 = 2000 kPa·s (Kelvin part). Under a constant stress of 20 kPa, with ε(t) = σ0/E1 + σ0 t/η1 + (σ0/E2)[1 − exp(−E2 t/η2)], the strain at t = 10 s is

  1. 0.1382
  2. 0.1132
  3. 0.1750
  4. 0.1500
Answer and working

A. 0.1382

Instantaneous 20/400 = 0.0500; flow 20 × 10/8000 = 0.0250; delayed 20/200 × (1 − e^(−1)) = 0.1 × 0.6321 = 0.0632. Total = 0.1382. 0.1132 omits the viscous flow term; 0.1750 takes the delayed elastic strain as complete; 0.1500 keeps only the two springs.

Question 7 · medium

In an oscillatory test within the linear viscoelastic region, a yoghurt gel gives G' = 1200 Pa and G'' = 300 Pa. The loss tangent and the behaviour it indicates are

  1. tan δ = 4.00, predominantly viscous, liquid-like
  2. tan δ = 0.20, a Newtonian liquid
  3. tan δ = 0.25, predominantly elastic, gel-like
  4. tan δ = 14.04, a purely elastic solid
Answer and working

C. tan δ = 0.25, predominantly elastic, gel-like

tan δ = G''/G' = 300/1200 = 0.25 (δ = 14.0°); G' > G'' means elastic behaviour dominates, as in a gel. 4.00 inverts the ratio; 0.20 divides by the sum; 14.04 is δ in degrees, not tan δ, and a purely elastic solid would have δ = 0.

Question 8 · hard

A ripening tomato reads a* = 24 and b* = 18 in CIE L*a*b*. Its hue angle h = arctan(b*/a*) and chroma C* = √(a*² + b*²) are

  1. h = 53.1°, C* = 30.0
  2. h = 36.9°, C* = 30.0
  3. h = 36.9°, C* = 42.0
  4. h = 0.644°, C* = 43.2
Answer and working

B. h = 36.9°, C* = 30.0

h = arctan(18/24) = 36.9° (first quadrant since a* and b* are positive) and C* = √(576 + 324) = 30.0. 53.1° inverts the ratio; C* = 42.0 adds the coordinates instead of combining them vectorially; 0.644 is the angle in radians labelled as degrees.

Question 9 · medium

Near-infrared spectroscopy predicts protein, oil and moisture in whole grain because

  1. O-H, C-H and N-H overtone and combination bands absorb in the NIR and are calibrated against lab analyses
  2. each nutrient emits light at its own characteristic visible wavelength when it is excited by the infrared source
  3. NIR radiation ionises the grain and the ions are counted by mass in the detector
  4. the NIR beam measures the kernel's dielectric loss factor, which equals its protein content
Answer and working

A. O-H, C-H and N-H overtone and combination bands absorb in the NIR and are calibrated against lab analyses

NIR absorption arises from overtones and combinations of bond vibrations; chemometric calibration against laboratory methods turns spectra into composition. Grain does not emit nutrient-specific visible light under NIR, NIR is non-ionising, and dielectric loss is a microwave/RF property.

Question 10 · hard

Henderson's equation is 1 − a_w = exp(−c T Mⁿ), with T in kelvin and M in % dry basis. For illustrative constants c = 1.0 × 10⁻⁵ and n = 2.0, the equilibrium moisture content at a_w = 0.70 and 27 °C is

  1. 20.0% d.b.
  2. 66.8% d.b.
  3. 10.9% d.b.
  4. 16.7% d.b.
Answer and working

A. 20.0% d.b.

−ln(1 − 0.70) = −ln 0.30 = 1.204; c T = 1.0 × 10⁻⁵ × 300 = 0.003; Mⁿ = 1.204/0.003 = 401.3; M = √401.3 = 20.0% d.b. 66.8 results from using T = 27 in °C; 10.9 uses ln(a_w) instead of ln(1 − a_w); 16.7 is the wet-basis value mislabelled as dry basis.

A study plan for Engineering Properties of Agricultural Produce in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (61% of the 57 questions): Viscoelastic models (12, 21%); Rheology: Newtonian and non-Newtonian flow (8, 14%); Water activity (8, 14%); Electrical and optical properties (7, 12%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Thermal properties: specific heat, conductivity and diffusivity (6, 11%); Aerodynamic properties: terminal velocity (5, 9%); Frictional properties: angle of repose and coefficient of friction (3, 5%); Porosity (3, 5%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Size and shape: sphericity and roundness (3, 5%); Volume and density: bulk and true (2, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Frictional properties: angle of repose and coefficient of friction (2 hard of 3), Porosity (2 hard of 3), Rheology: Newtonian and non-Newtonian flow (5 hard of 8).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Viscoelastic models (3 easy of 12); Thermal properties: specific heat, conductivity and diffusivity (1 easy of 6).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Engineering Properties of Agricultural Produce

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.