LAISHA
Open Laisha

ICAR AICE-JRF/SRF Mechanics of Tillage & Traction (Soil Dynamics): practice questions

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
53written to this exam in this subject
13syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Mechanics of Tillage & Traction (Soil Dynamics) in ICAR AICE-JRF/SRF

Unit 6 soil dynamics in tillage and traction at PG depth: Mohr-Coulomb and soil-metal friction, soil failure and critical depth, Reece's equation, Bekker and Janosi-Hanamoto models, mobility numbers, compaction models.

How soil resists tools and supports wheels: draft, slip, tractive efficiency, weight transfer and stability.

Our 53 ICAR AICE-JRF/SRF questions in this subject: 2 easy, 26 medium, 25 hard, across 13 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · medium

Which field instrument measures both the pressure-sinkage relationship and the shear stress-displacement relationship of a soil for vehicle mobility work?

  1. Proctor compaction apparatus
  2. Bevameter
  3. Casagrande liquid limit device
  4. Standard cone penetrometer
Answer and working

B. Bevameter

The bevameter combines a sinkage plate test (Bekker's kc, kφ, n) with a shear ring test (c, φ, K). The cone penetrometer gives a single composite cone index; the Proctor and Casagrande devices are laboratory tests for compaction and consistency.

Question 2 · medium

Why does the draft of most tillage tools rise with travel speed?

  1. Soil shear strength always doubles when speed doubles, so draft rises in direct proportion to the speed
  2. Soil moved by the tool must be accelerated, adding an inertial force that grows with speed
  3. Wheel slip falls as speed rises, increasing depth
  4. Adhesion becomes zero at low speed
Answer and working

B. Soil moved by the tool must be accelerated, adding an inertial force that grows with speed

The inertial term, proportional to the mass rate of soil moved times its velocity change, rises roughly with speed squared. This is why the ASABE draft equation includes an S² term for implements like the mouldboard plough.

Question 3 · easy

A tractor carries 20 kN on its drive wheels on dry sand (c = 0, φ = 30°). What is the maximum thrust the soil can provide?

  1. 10.00 kN
  2. 34.64 kN
  3. 17.32 kN
  4. 11.55 kN
Answer and working

D. 11.55 kN

H = A·c + W tan φ; with c = 0, H = 20 × tan 30° = 11.55 kN. Contact area does not matter in dry sand. Using sin φ gives 10.00 kN. 34.64 kN divides by tan φ; 17.32 kN uses cos φ.

Question 4 · medium

In Bekker's pressure-sinkage equation p = (kc/b + kφ)zⁿ, b is

  1. the wheel diameter
  2. the bulk density of the soil
  3. the lug spacing
  4. the smaller dimension of the contact area
Answer and working

D. the smaller dimension of the contact area

Bekker used the smaller dimension of the loading area; kc is the cohesive modulus and kφ the frictional modulus of deformation. For a tyre, b is the contact width.

Question 5 · hard

A tyre operates at net traction ratio 0.4, motion resistance ratio 0.08 and slip 10 %. What is its tractive efficiency?

  1. 83.3 %
  2. 112.5 %
  3. 75.0 %
  4. 8.3 %
Answer and working

C. 75.0 %

TE = (1 − s) × NTR/(NTR + MRR) = 0.90 × 0.4/0.48 = 75.0 %. GTR = NTR + MRR; subtracting MRR instead gives an efficiency above the true value. 83.3 % omits the (1 − s) term; 112.5 % comes from subtracting MRR (0.4/0.32); 8.3 % multiplies by s instead of (1 − s).

Question 6 · hard

A longer track contact length, at the same load and width, develops a given thrust at lower slip because

  1. cohesion increases with contact length
  2. the angle of internal friction increases with length
  3. rolling resistance becomes negative on long tracks, so part of the thrust is supplied free by the soil
  4. shear displacement accumulates along the contact length, mobilising soil shear strength sooner
Answer and working

D. shear displacement accumulates along the contact length, mobilising soil shear strength sooner

Shear displacement j at a point grows with its distance from the front of the contact (j = s·x). A long contact mobilises more of the soil's shear strength at a given slip, so thrust builds at lower slip.

Question 7 · hard

A penetrometer using the 130 mm² cone records 260 N at 10 cm depth. A colleague mistakenly uses the 323 mm² base area. By what factor does the colleague underestimate the cone index?

  1. 2.48
  2. 0.40
  3. 6.17
  4. 1.58
Answer and working

A. 2.48

Correct CI = 260/130×10⁻⁶ = 2.0 MPa; with the wrong area 260/323×10⁻⁶ = 0.805 MPa. Ratio = 323/130 = 2.48. CI scales with 1/area, not with the square or square root. 0.40 inverts the ratio; 6.17 squares it; 1.58 takes its square root.

Question 8 · hard

A tractor (track 1.4 m, CG height 0.8 m, CG on the centreline) turns on level ground on a 5 m radius. Above what speed will it begin to overturn outwards?

  1. 6.55 km/h
  2. 33.4 km/h
  3. 154.5 km/h
  4. 23.6 km/h
Answer and working

D. 23.6 km/h

Overturn when v²/(g r) = (t/2)/h → v = √(g r t/(2h)) = √(9.81 × 5 × 1.4/(2 × 0.8)) = 6.55 m/s = 23.6 km/h. Using full track in place of half gives 33.4 km/h; quoting m/s as km/h is a unit slip. 154.5 km/h forgets the square root (42.9 × 3.6).

Question 9 · medium

On a 2WD tractor pulling a load on level ground in steady motion, the horizontal force balance gives

  1. rear wheel net thrust = drawbar pull − front wheel rolling resistance
  2. rear wheel gross thrust = drawbar pull
  3. rear wheel net thrust = drawbar pull + front wheel rolling resistance
  4. front wheel rolling resistance = drawbar pull
Answer and working

C. rear wheel net thrust = drawbar pull + front wheel rolling resistance

The rear tyres must overcome both the implement and the front wheels' rolling resistance. Gross thrust is larger still, since it also covers the rear wheels' own motion resistance.

Question 10 · medium

In a three-point linkage, what is the virtual hitch point?

  1. The drawbar pin
  2. The point where the lower links attach to the tractor
  3. The point where the lines of the upper and lower links, extended, intersect in side view
  4. The centre of resistance of the implement
Answer and working

C. The point where the lines of the upper and lower links, extended, intersect in side view

The linkage acts as if the implement were hitched at the instantaneous centre where the extended link lines meet; its position determines how the implement's forces are transferred to the tractor.

A study plan for Mechanics of Tillage & Traction (Soil Dynamics) in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (49% of the 53 questions): Traction theory: slip, rolling resistance and net traction (7, 13%); Soil-tool mechanics (6, 11%); Soil compaction by vehicles (5, 9%); Cone index and cone penetrometer (4, 8%); Dynamic properties and strength of soil (4, 8%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Longitudinal and lateral stability (4, 8%); Traction in wetland soils (4, 8%); Tractive efficiency (4, 8%); Tractor chassis mechanics (4, 8%); Wheel and track mechanics (4, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Determination of the centre of gravity (3, 6%); Weight transfer (3, 6%); Prediction of draft (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Longitudinal and lateral stability (4 hard of 4), Tractive efficiency (3 hard of 4), Determination of the centre of gravity (2 hard of 3).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Soil-tool mechanics (1 easy of 6); Traction theory: slip, rolling resistance and net traction (1 easy of 7).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Mechanics of Tillage & Traction (Soil Dynamics)

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.