ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR
Original practice questions written to the published syllabus · not past papersICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.
Source: icar.org.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Design of farm machine components at postgraduate depth: fatigue under variable soil loads, Goodman and Soderberg design, bearing selection, overload protection, and measurement of force, torque and strain for design data.
Sizing the parts of farm machines so they do not fail: shafts, keys, joints, springs, bearings, drives and overload devices.
Our 43 ICAR AICE-JRF/SRF questions in this subject: 1 easy, 20 medium, 22 hard, across 13 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.
At a point in a ductile part the in-plane principal stresses are 120 MPa (tension) and 40 MPa (compression); the third principal stress is zero. The yield strength is 320 MPa. What is the factor of safety by the maximum shear stress (Tresca) theory?
A. 2.00
Tresca: yield when sigma1 - sigma3 reaches Syt. With principal stresses 120, 0 and -40 MPa, the largest difference is 120 - (-40) = 160 MPa (maximum shear 80 MPa against Syt/2 = 160 MPa), so N = 320/160 = 2.00. Using only the largest principal stress gives 2.67 (Rankine). Von Mises, sqrt(sigma1^2 - sigma1 sigma2 + sigma2^2) = 144.2 MPa, gives 2.22. Adding the stresses algebraically (80 MPa) is not a failure theory. 4.00 divides Syt by the maximum shear stress (320/80) instead of comparing it with Syt/2.
A solid shaft of 50 mm diameter is to be replaced by a hollow shaft of the same material with inner diameter half the outer diameter, carrying the same torque at the same maximum shear stress. What outer diameter is needed?
C. 51.1 mm
Equal strength: d^3 = do^3 (1 - k^4), so do = 50/(1 - 0.5^4)^(1/3) = 50/(0.9375)^(1/3) = 51.1 mm. Using (1 - k^2) gives 55.0 mm, and forgetting the cube root gives 53.3 mm. The hollow shaft weighs about 78 per cent of the solid one.
The hitch pin of a trailed implement is a clevis-and-pin (knuckle-type) joint. In service the pin bends and wears oval. Which statement about its design is correct?
C. The pin must be checked for bending and bearing as well as double shear, and it should be secured so it cannot work out
In a clevis the pin acts as a short beam between the fork prongs, so bending often governs; bearing pressure causes the oval wear seen. Double shear is also checked. Clearance increases bending and impact, and the securing clip matters because a lost pin causes run-away implements.
A bolt is preloaded to 10 kN. The bolt stiffness is 200 kN/mm and the stiffness of the clamped parts is 800 kN/mm. An external tensile load of 6 kN is then applied to the joint. What is the bolt load?
A. 11.2 kN
Joint constant C = kb/(kb + km) = 200/(200+800) = 0.2. Bolt load = Fi + C P = 10 + 0.2 x 6 = 11.2 kN. Adding the whole load (16 kN) ignores the stiff members; 14.8 kN applies the member share to the bolt. The clamping force falls to 5.2 kN.
Why are welded steel details in fatigue design codes often assessed on stress range alone, with little or no correction for mean stress?
A. Welding leaves tensile residual stresses near yield, so the local mean stress is already high whatever the applied mean
Shrinkage of the weld as it cools locks in tensile residual stress of the order of the yield strength near the toe. The effective mean stress is therefore high regardless of the applied load, and the applied stress range governs crack growth. Mean stress does matter for unwelded parts, and welds are not left in compression.
A belt has a maximum allowable tension of 1800 N and a mass of 0.6 kg/m. At what belt speed does it transmit maximum power?
D. 31.6 m/s
Maximum power occurs when Tc = Tmax/3, i.e. m v^2 = Tmax/3, so v = sqrt(Tmax/(3m)) = sqrt(1800/(3 x 0.6)) = 31.6 m/s. sqrt(Tmax/m) = 54.8 m/s is the speed where all tension is centrifugal and no power is transmitted. 1000 m/s forgets the square root (1800/1.8); 38.7 m/s sets Tc = Tmax/2.
A 20-tooth pinion meshes externally with a 40-tooth gear; module 4 mm, face width 40 mm, and load-stress factor K = 1.2 N/mm^2. What is Buckingham's wear strength Sw = b Q dp K?
A. 5120 N
Q = 2 zg/(zg + zp) = 2 x 40/60 = 1.333; dp = m zp = 80 mm. Sw = 40 x 1.333 x 80 x 1.2 = 5120 N. Using zp in the numerator of Q gives 2560 N; using the gear diameter gives 10240 N. 3840 N takes Q = 1, ignoring the ratio factor.
A baler drive normally sees peak working torques up to 250 N m. The gearbox is damaged above 600 N m. The designer wants the shear bolt to break at 1.4 times the peak working torque. Is this setting acceptable?
A. Yes: it breaks at 350 N m, above normal peaks and below the damaging 600 N m
Break torque = 1.4 x 250 = 350 N m. This lies above the normal peaks (no nuisance breaks) and below 600 N m (the gearbox is protected). Setting it at the working torque would break the bolt in normal use.
Which transducer is widely used in tillage research to measure the horizontal (draft) and vertical forces on a soil-engaging tool?
A. The extended octagonal ring transducer with strain gauges
The extended octagonal ring, fitted with strain gauges at nodes that respond selectively to horizontal and vertical force, separates draft and vertical load and can also give moment. A Bourdon tube measures fluid pressure, a thermocouple temperature and a tachogenerator speed.
A knuckle joint pin is often analysed for bending by assuming a load distribution between two limiting cases. Why?
D. The actual pressure distribution along the pin depends on fit and deflection, so the true bending moment lies between the uniformly distributed and the concentrated-load cases
With a clearance fit the load is concentrated near the edges of the eye and fork; with a tight fit it is spread. Textbooks take a moment between these limits, commonly a mean of the two cases, and size the pin accordingly. The pin does bend, is in double shear, and the joint carries tension.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.