ICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 · India · National Testing Agency for ICAR
Original practice questions written to the published syllabus · not past papersICAR AICE-JRF/SRF (PhD) — Agricultural Engineering subjects 38–43 is a PhD, fellowship and lectureship exam run by National Testing Agency for ICAR, for candidates in India. LAN-based computer test, 2 hours, 120 MCQs: 20 Part A (general knowledge and reasoning), 50 Part B (core group), 50 Part C (specialisation); four options.
Source: icar.org.in.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
PG-depth fluid mechanics and open-channel hydraulics: derivations and limits of Darcy-Weisbach and Hazen-Williams, Moody zones, Hardy Cross, specific energy and transitions, critical flow in non-rectangular sections, jump classification, gradually varied flow ideas and model laws.
Fluids at rest and in motion, pipe flow and open channels: the base of irrigation, drainage, pumping and conservation structures.
Our 67 ICAR AICE-JRF/SRF questions in this subject: 5 easy, 38 medium, 24 hard, across 18 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.
A soap bubble 40 mm in diameter is made from a solution with surface tension 0.04 N/m. What is the excess of pressure inside the bubble over the outside?
D. 8.00 Pa
A soap bubble has two surfaces, so Δp = 8σ/d = 8 × 0.04/0.04 = 8.00 Pa. 4σ/d = 4.00 Pa is the result for a liquid droplet (one surface); 2σ/d is for a cylindrical jet; using the radius in 8σ/d gives 16.0 Pa.
An inverted U-tube manometer with oil of relative density 0.8 in its upper bend is connected between two points on a water pipeline. The oil-water interfaces differ in level by 200 mm. What is the difference in piezometric head between the two points, in metres of water?
C. 0.0400 m
For a lighter manometric liquid, h = x(1 − S_light/S) = 0.2 × (1 − 0.8) = 0.0400 m of water. Using x × S_light gives 0.160 m; the inverted manometer is chosen precisely because it gives a large deflection for a small head difference. 0.360 m uses (1 + 0.8) instead of (1 − 0.8).
For which of these situations is the Hazen-Williams equation NOT appropriate?
B. Laminar flow of oil in a hydraulic line
Hazen-Williams is empirical and fitted to turbulent flow of water at ordinary temperatures. It has no viscosity term, so it cannot handle other fluids or laminar flow; Darcy-Weisbach with f = 64/Re (laminar) or the Moody diagram must be used instead.
A pipe contracts suddenly and the velocity in the smaller pipe is 3 m/s. If the coefficient of contraction at the vena contracta is 0.62, what is the head loss at the contraction?
B. 0.172 m
h_c = (1/C_c − 1)² V₂²/2g = (1/0.62 − 1)² × 9/19.62 = 0.376 × 0.459 = 0.172 m. The rule of thumb 0.5V₂²/2g gives 0.229 m when C_c is not known; forgetting to square gives 0.281 m. 0.0662 m uses (1 − C_c)² instead of (1/C_c − 1)².
What is the coefficient of discharge of an internal (Borda, re-entrant) mouthpiece running free, where the jet does not touch the mouthpiece walls?
B. 0.50
Momentum analysis of the Borda mouthpiece, where the wall pressure around the entrance is hydrostatic, gives C_c = 0.5; with C_v ≈ 1, C_d = 0.5. Running full, C_d is about 0.707. 0.855 is the external cylindrical mouthpiece. 0.62 is the usual sharp-edged orifice value.
A rectangular sharp-crested weir 2 m long, with end contractions at both ends, runs under a head of 0.4 m. Using the Francis formula (SI), what is the discharge?
B. 0.894 m³/s
Q = 1.84(L − 0.1nH)H^1.5 with n = 2: effective length = 2 − 0.1 × 2 × 0.4 = 1.92 m, Q = 1.84 × 1.92 × 0.4^1.5 = 0.894 m³/s. Ignoring the contractions gives 0.931 m³/s; counting only one gives 0.912 m³/s. 0.357 m³/s uses H^2.5 instead of H^1.5.
A hydraulic jump in a horizontal rectangular channel has depths of 0.5 m before and 2.0 m after the jump. What is the head loss in the jump?
B. 0.844 m
ΔE = (y₂ − y₁)³/(4y₁y₂) = 1.5³/(4 × 0.5 × 2.0) = 3.375/4 = 0.844 m. Omitting the 4 gives 3.38 m; squaring instead of cubing gives 0.562 m; 1.50 m is the jump height, not the loss.
In the US Bureau of Reclamation classification, what type of jump forms when the upstream Froude number is about 6?
D. Steady jump
Fr₁ of about 4.5–9 gives a steady, well-balanced jump, preferred in stilling basins. 2.5–4.5 is oscillating (sends waves downstream, avoided); 1.7–2.5 weak; 1–1.7 undular; above 9 strong.
In a hydraulic jump in a horizontal rectangular channel the sequent depth is six times the initial depth. What is the upstream Froude number?
B. 4.58
From y₂/y₁ = ½[√(1 + 8Fr₁²) − 1] = 6: √(1 + 8Fr₁²) = 13, so 8Fr₁² = 168, Fr₁² = 21 and Fr₁ = 4.58. The depth ratio itself (6) is not the Froude number. 2.45 is √6 and 3.46 is √(2 × 6), neither from the jump equation.
Flow through a large pipe valve is studied on a 1:10 model using the same water at the same temperature. For dynamic similarity (Reynolds' law), what model velocity corresponds to a prototype velocity of 1.5 m/s?
A. 15 m/s
Reynolds similarity with the same fluid needs V_m D_m = V_p D_p, so V_m = V_p × (D_p/D_m) = 1.5 × 10 = 15 m/s. Using Froude scaling (V ∝ L^0.5) gives 0.474 m/s, which is wrong for a closed conduit where gravity plays no role in the dynamics. 4.74 m/s multiplies by √10 and 0.15 m/s divides by 10.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.