LAISHA
Open Laisha

NCEES FE Other Disciplines Fluid Mechanics & Open Channel Hydraulics: practice questions

NCEES FE Other Disciplines · USA · NCEES

Original practice questions written to the published syllabus · not past papers
10worked here, free
48written to this exam in this subject
16syllabus units

About NCEES FE Other Disciplines

NCEES FE Other Disciplines is a licensing and registration exam run by NCEES, for candidates in USA. Computer-based, 110 questions, 6-hour appointment (5 h 20 min exam).

Source: ncees.org.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Fluid Mechanics & Open Channel Hydraulics in NCEES FE Other Disciplines

Fluid mechanics is the heaviest area (12–18 questions): properties, statics and manometers, buoyancy, continuity, energy and momentum equations, pipe friction with the Moody diagram, flow measurement and similitude, often in US customary units, answered with the NCEES Reference Handbook.

Fluids at rest and in motion, pipe flow and open channels: the base of irrigation, drainage, pumping and conservation structures.

Our 48 NCEES FE Other Disciplines questions in this subject: 13 easy, 27 medium, 8 hard, across 16 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to NCEES FE Other Disciplines and are not shown on any other exam's page.

Question 1 · medium

A flat plate slides at 0.5 m/s over a film of oil 0.5 mm thick resting on a fixed surface. The oil's dynamic viscosity is 1 poise and the velocity profile in the film is linear. What is the shear stress on the plate?

  1. 100 Pa
  2. 1000 Pa
  3. 0.100 Pa
  4. 10.0 Pa
Answer and working

A. 100 Pa

1 poise = 0.1 Pa·s. τ = μ du/dy = 0.1 × 0.5/(0.5 × 10⁻³) = 100 Pa. Taking 1 poise as 1 Pa·s gives 1000 Pa (ten times too large); leaving the gap in millimetres gives 0.100 Pa.

Question 2 · medium

A mercury differential manometer (relative density 13.6) connected across two points in a pipe carrying water shows a deflection of 150 mm. What is the difference in piezometric head between the two points, in metres of water?

  1. 0.150 m
  2. 2.04 m
  3. 1.89 m
  4. 2.19 m
Answer and working

C. 1.89 m

h = x(S_m/S − 1) = 0.15 × (13.6 − 1) = 1.89 m of water. Using 13.6 instead of 12.6 (2.04 m) forgets the water standing above the mercury in both limbs. 2.19 m uses (13.6 + 1) instead of (13.6 − 1).

Question 3 · easy

A vacuum gauge on a pump suction pipe reads 40 kPa (vacuum) where local atmospheric pressure is 101.3 kPa. What is the absolute pressure in the pipe?

  1. 61.3 kPa
  2. 40.0 kPa
  3. 141.3 kPa
  4. −40.0 kPa
Answer and working

A. 61.3 kPa

Absolute = atmospheric + gauge = 101.3 + (−40) = 61.3 kPa. −40 kPa is the gauge pressure, and 141.3 kPa results from adding a vacuum reading as if it were positive.

Question 4 · medium

A horizontal venturimeter 150 mm × 75 mm carries water. A mercury-water differential manometer (mercury relative density 13.6) connected between inlet and throat reads 200 mm. With a discharge coefficient of 0.97, what is the discharge?

  1. 31.1 L/s
  2. 32.1 L/s
  3. 8.77 L/s
  4. 32.3 L/s
Answer and working

A. 31.1 L/s

h = 0.2 × (13.6 − 1) = 2.52 m of water. a₁ = 0.0177 m², a₂ = 0.00442 m². Q = C_d a₁a₂√(2gh)/√(a₁² − a₂²) = 0.97 × 0.0177 × 0.00442 × √(2 × 9.81 × 2.52)/√(0.0177² − 0.00442²) = 0.0311 m³/s = 31.1 L/s. Using 13.6x for h gives 32.3 L/s; omitting C_d gives 32.1 L/s. 8.77 L/s takes the 0.2 m mercury reading as the water head.

Question 5 · medium

Water flows upward through a pipe that reduces from 300 mm diameter at section 1 to 150 mm at section 2, which is 5 m higher. The discharge is 0.1 m³/s and the pressure at section 1 is 200 kPa (gauge). Neglecting losses, what is the pressure at section 2?

  1. 185 kPa
  2. 166 kPa
  3. 151 kPa
  4. 136 kPa
Answer and working

D. 136 kPa

V₁ = 0.1/0.0707 = 1.41 m/s; V₂ = 0.1/0.0177 = 5.66 m/s. p₂ = p₁ − ρg(z₂ − z₁) − ρ(V₂² − V₁²)/2 = 200 − 49.05 − 15.0 = 136 kPa. Ignoring the velocity change gives 151 kPa; ignoring the rise gives 185 kPa. 166 kPa adds the change in velocity head instead of subtracting it (200 − 49.05 + 15.0).

Question 6 · easy

Oil with kinematic viscosity 1 × 10⁻⁴ m²/s flows at 1.5 m/s in a 100 mm pipe. What is the Reynolds number and the flow regime?

  1. 150000, turbulent
  2. 750.0, laminar
  3. 1500, laminar
  4. 1500, turbulent
Answer and working

C. 1500, laminar

Re = VD/ν = 1.5 × 0.1/10⁻⁴ = 1500, below about 2000, so laminar. Using water's ν (10⁻⁶ m²/s) gives 150000; using the radius gives 750.0.

Question 7 · medium

A pipe carrying 30 L/s of water enlarges suddenly from 100 mm to 200 mm diameter. What is the head loss at the enlargement?

  1. 0.744 m
  2. 0.372 m
  3. 0.697 m
  4. 0.418 m
Answer and working

D. 0.418 m

V₁ = 0.03/(π × 0.1²/4) = 3.82 m/s; V₂ = 0.955 m/s. Borda-Carnot: h_e = (V₁ − V₂)²/2g = (2.86)²/19.62 = 0.418 m. (V₁² − V₂²)/2g = 0.697 m is the difference of velocity heads, not the loss; part of it is recovered as pressure. 0.744 m takes the whole inlet velocity head V₁²/2g; 0.372 m takes half of it.

Question 8 · medium

A valve with loss coefficient K = 10 is fitted in a 100 mm pipe whose Darcy friction factor is 0.02. What equivalent length of straight pipe produces the same loss?

  1. 50 m
  2. 5 m
  3. 0.5 m
  4. 500 m
Answer and working

A. 50 m

Equate KV²/2g to f(L_e/D)V²/2g: L_e = KD/f = 10 × 0.1/0.02 = 50 m. Omitting the diameter gives K/f = 500 m; 5 m and 0.5 m are factor-of-ten slips in D or f.

Question 9 · hard

A vertical cylindrical tank 2 m in diameter drains through a 50 mm orifice in its base (C_d = 0.6). How long does the water level take to fall from 3 m to 1 m above the orifice?

  1. 14.7 min
  2. 34.8 min
  3. 11.6 min
  4. 7.35 min
Answer and working

A. 14.7 min

T = 2A(√H₁ − √H₂)/(C_d a √2g). A = π × 2²/4 = 3.14 m², a = 0.00196 m². T = 2 × 3.14 × (√3 − 1)/(0.6 × 0.00196 × 4.429) = 881 s = 14.7 min. Assuming a constant outflow at the initial head gives 11.6 min (too short); 34.8 min is the time to empty completely; omitting the factor 2 halves the answer. That halved value is 7.35 min.

Question 10 · medium

A concrete-lined rectangular channel 3 m wide carries water at a uniform depth of 1.2 m on a bed slope of 0.001. With Manning's n = 0.015, what is the discharge?

  1. 4.31 m³/s
  2. 0.183 m³/s
  3. 5.79 m³/s
  4. 8.57 m³/s
Answer and working

C. 5.79 m³/s

A = 3 × 1.2 = 3.60 m²; P = 3 + 2 × 1.2 = 5.40 m (free surface excluded); R = 0.667 m. V = (1/n)R^(2/3)S^(1/2) = (1/0.015) × 0.763 × 0.0316 = 1.61 m/s; Q = 5.79 m³/s. Taking R = y (wide-channel approximation) gives 8.57 m³/s; including the free surface in P (P = 8.40 m) gives 4.31 m³/s. 0.183 m³/s uses S instead of √S.

A study plan for Fluid Mechanics & Open Channel Hydraulics in NCEES FE Other Disciplines

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (56% of the 48 questions): Hydrostatics and manometry (6, 13%); Bernoulli's equation: venturimeter, orifice meter and pitot tube (5, 10%); Forces on submerged surfaces and buoyancy (5, 10%); Minor losses (4, 8%); Properties of fluids (4, 8%); Continuity equation (3, 6%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Darcy-Weisbach equation and Moody diagram (3, 6%); Dimensional analysis and similitude (3, 6%); Laminar and turbulent flow in pipes (3, 6%); Momentum equation (2, 4%); Orifices, mouthpieces and tank emptying (2, 4%); Pipes in series and parallel (2, 4%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Specific energy and critical depth (2, 4%); Uniform flow in open channels: Manning and Chezy (2, 4%); Hazen-Williams equation (1, 2%); Weirs and notches (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Momentum equation (1 hard of 2), Orifices, mouthpieces and tank emptying (1 hard of 2), Pipes in series and parallel (1 hard of 2).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Continuity equation (2 easy of 3); Pipes in series and parallel (1 easy of 2).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — NCEES FE Other Disciplines Fluid Mechanics & Open Channel Hydraulics

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.