ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering · India · Agricultural Scientists Recruitment Board (ICAR)
Original practice questions written to the published syllabus · not past papersASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering is a specialist certification exam run by Agricultural Scientists Recruitment Board (ICAR), for candidates in India. NET: 150 MCQs, 150 marks, 2 hours, −1/3 per wrong answer, English/Hindi, PG level. Combined NET/ARS/SMS/STO recruitment runs prelims, mains and interview.
Official site: pw.live.
We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.
Similar to the ICAR PhD paper: standard results and their conditions across pipe flow, flow measurement and open-channel hydraulics.
Fluids at rest and in motion, pipe flow and open channels: the base of irrigation, drainage, pumping and conservation structures.
Our 35 ASRB NET questions in this subject: 4 easy, 14 medium, 17 hard, across 17 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ASRB NET and are not shown on any other exam's page.
A rectangular pontoon 6 m long and 3 m wide floats in fresh water with a draught of 1.0 m. Its centre of gravity is 1.0 m above the bottom. What is its metacentric height for rolling about the long axis, and is it stable?
A. 0.25 m, stable
V = 6 × 3 × 1 = 18 m³; I = Lb³/12 = 6 × 27/12 = 13.5 m⁴; BM = I/V = 0.75 m. B is at half the draught, 0.5 m above the bottom, so BG = 1.0 − 0.5 = 0.5 m. GM = BM − BG = 0.25 m > 0, so stable. Adding BG instead of subtracting gives 1.25 m.
A proposed two-dimensional steady incompressible flow has the velocity component u = 2x in the x-direction. Which y-component makes the flow satisfy continuity (taking v = 0 on y = 0)?
C. v = −2y
Continuity for 2-D incompressible flow requires ∂u/∂x + ∂v/∂y = 0. ∂u/∂x = 2, so ∂v/∂y = −2 and v = −2y + f(x); with v = 0 on y = 0, f(x) = 0. v = 2y gives a divergence of 4, which is impossible for an incompressible fluid.
Laminar flow of a given discharge passes through a pipe. If the pipe diameter is halved while the discharge and length stay the same, by what factor does the friction head loss change?
D. It increases 16 times
Hagen-Poiseuille: h_f = 32μVL/(ρgD²) and V = 4Q/(πD²), so h_f ∝ Q/D⁴. Halving D multiplies h_f by 2⁴ = 16. The factor 32 would follow from the turbulent Darcy form with constant f (h_f ∝ 1/D⁵).
Two reservoirs with a 5 m difference in water level are joined by a 50 m pipe of 100 mm diameter with a sharp-edged entrance (K = 0.5) and exit loss (K = 1.0). The Darcy friction factor is 0.02. What is the discharge?
A. 22.9 L/s
Energy from surface to surface: 5 = (K_ent + K_exit + fL/D)V²/2g = (0.5 + 1.0 + 0.02 × 500)V²/2g = 11.5 V²/2g. V = √(2 × 9.81 × 5/11.5) = 2.92 m/s; Q = 22.9 L/s. Ignoring minor losses gives 24.6 L/s; forgetting the exit loss gives 24.0 L/s; using 4f gives 12.1 L/s.
A total flow of 100 L/s divides between two parallel pipes of equal length and friction factor, 200 mm and 100 mm in diameter. How much flows through the 200 mm pipe?
C. 85.0 L/s
Q₁/Q₂ = (D₁/D₂)^2.5 = 5.66 (equal head loss, h_f ∝ Q²/D⁵). Q₁ = 100 × 5.66/(1 + 5.66) = 85.0 L/s. Splitting in the ratio of areas (4:1) gives 80 L/s; in the ratio of diameters, 66.7 L/s. 97.0 L/s splits in the ratio of D⁵ (32:1) without the square root.
A rectangular channel 4 m wide carries 8 m³/s at a depth of 0.5 m. What is the alternate depth, the depth on the other limb of the specific-energy curve with the same specific energy?
A. 1.17 m
q = 8/4 = 2 m²/s. E = y + q²/(2gy²) = 0.5 + 4/(19.62 × 0.25) = 1.32 m. Solving y + 0.2039/y² = 1.32 on the subcritical limb gives y ≈ 1.17 m. 0.742 m is the critical depth; 1.05 m is the sequent depth of a hydraulic jump, which conserves momentum, not energy.
A triangular channel with side slopes 1 horizontal to 1 vertical carries 2 m³/s. What is the critical depth?
C. 0.960 m
The general critical condition is Q²T/(gA³) = 1. For z = 1: A = y², T = 2y, so Q² × 2y/(g y⁶) = 1, y⁵ = 2Q²/g = 0.815, y_c = 0.960 m. Using the rectangular formula (q²/g)^(1/3) with Q gives 0.742 m, which does not apply to a triangle. 0.836 m forgets the factor 2 from T = 2y (y⁵ = Q²/g); 1.46 m takes the area as y²/2.
Subcritical flow in a rectangular channel passes over a smooth, low hump in the bed without choking. Neglecting losses, what happens to the water surface over the hump?
B. It drops
The specific energy over the hump is reduced by the hump height. On the subcritical (upper) limb of the E-y curve, lower E means lower depth, and the drop in depth exceeds the hump height, so the surface drops. In supercritical flow the depth, and the surface, would rise.
Water leaves a sluice gate at a depth of 0.35 m with a discharge of 4 m³/s per metre width and forms a hydraulic jump on a horizontal apron. What fraction of the incoming specific energy is dissipated in the jump?
C. About 57 %
V₁ = 4/0.35 = 11.4 m/s; Fr₁ = 11.4/√(9.81 × 0.35) = 6.17. y₂ = 0.175[√(1 + 8 × 6.17²) − 1] = 2.88 m. ΔE = (y₂ − y₁)³/(4y₁y₂) = 4.03 m. E₁ = 0.35 + 11.4²/19.62 = 7.01 m, so the loss is 57 % of E₁. 43 % is the fraction retained downstream, not the fraction lost. About 3.5 % comes from forgetting to square Fr₁ (y₂ = 1.07 m); 88 % is (y₂ − y₁)/y₂, a depth ratio, not an energy ratio.
The measured depths before and after a hydraulic jump in a horizontal rectangular channel are 0.3 m and 1.8 m. What discharge per unit width is passing?
C. 2.36 m²/s
From momentum, q² = g y₁ y₂ (y₁ + y₂)/2 = 9.81 × 0.3 × 1.8 × 2.1/2 = 5.56, so q = 2.36 m²/s. Omitting the /2 gives 3.34 m²/s; treating 1.8 m as a critical depth gives 7.56 m²/s. 1.99 m²/s uses (y₂ − y₁) instead of (y₁ + y₂).
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.