LAISHA
Open Laisha

ASRB NET Farm Power Sources: practice questions

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering · India · Agricultural Scientists Recruitment Board (ICAR)

Original practice questions written to the published syllabus · not past papers
10worked here, free
37written to this exam in this subject
8syllabus units

About ASRB NET

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering is a specialist certification exam run by Agricultural Scientists Recruitment Board (ICAR), for candidates in India. NET: 150 MCQs, 150 marks, 2 hours, −1/3 per wrong answer, English/Hindi, PG level. Combined NET/ARS/SMS/STO recruitment runs prelims, mains and interview.

Official site: pw.live.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Farm Power Sources in ASRB NET

Farm power scenario, draught animal power and harnessing, mechanisation indices and energy analysis; theory-heavy MCQs.

Where the energy for farm work comes from, how much is available, and how mechanisation is measured.

Our 37 ASRB NET questions in this subject: 7 easy, 18 medium, 12 hard, across 8 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ASRB NET and are not shown on any other exam's page.

Question 1 · medium

In an energy audit, male labour is counted at 1.96 MJ per man-hour. What energy input is recorded for 12 men working 8 hours each?

  1. 15.68 MJ
  2. 23.52 MJ
  3. 52.3 MJ
  4. 188.16 MJ
Answer and working

D. 188.16 MJ

Man-hours = 12 × 8 = 96; energy = 96 × 1.96 = 188.16 MJ. 15.68 MJ counts only one worker; 23.52 MJ forgets the hours; 52.3 is the same energy in kWh, wrongly labelled MJ.

Question 2 · medium

What is the main purpose of an evener (whippletree) when two animals pull one implement?

  1. To raise the line of draught so the implement penetrates deeper
  2. To increase the speed of the implement beyond that of either animal
  3. To share the load between the animals and keep the pull central
  4. To lock the animals' heads together
Answer and working

C. To share the load between the animals and keep the pull central

An evener is a pivoted bar that divides the load in a set proportion and prevents one animal doing all the work or pulling the implement sideways. It does not change speed or the draught angle by itself.

Question 3 · medium

A 35 kW tractor works 800 hours a year at an average load factor of 55%. What is its annual work output?

  1. 28,000 kWh
  2. 50,909 kWh
  3. 15.4 kWh
  4. 15,400 kWh
Answer and working

D. 15,400 kWh

Annual work = rated power × hours × load factor = 35 × 800 × 0.55 = 15,400 kWh (= 55.4 GJ). Ignoring the load factor gives 28,000 kWh; dividing by it gives 50,909 kWh; 15.4 is MWh labelled kWh.

Question 4 · hard

An audit finds a 15 kW motor driving a pump that needs only 6 kW. What is the main energy consequence?

  1. The motor overheats because it is overloaded
  2. Efficiency rises because losses fall with load
  3. The motor runs at low load, where both its efficiency and power factor are poor
  4. There is no effect at all, because a motor always draws only the power its load needs
Answer and working

C. The motor runs at low load, where both its efficiency and power factor are poor

At 40% load an induction motor's efficiency and power factor fall, so more energy and reactive current are drawn per kW delivered. It is underloaded, not overloaded; matching motor size to load is a standard energy-saving measure.

Question 5 · medium

Why are multi-blade, high-solidity rotors used on windmills that drive piston pumps for stock water?

  1. High starting torque at low wind speed and slow rotation suit a pump that starts under load
  2. They reach the highest tip speed ratios of any rotor
  3. They have the highest power coefficient of all rotor types, exceeding the Betz limit at low wind
  4. They need no tail vane or yawing mechanism
Answer and working

A. High starting torque at low wind speed and slow rotation suit a pump that starts under load

High solidity gives high torque at low speed (tip speed ratio about 1), which a reciprocating pump needs to start. Two- or three-blade low-solidity rotors run at high tip speed ratios and suit generators.

Question 6 · medium

Producer gas from an air-blown biomass gasifier has a low calorific value (roughly 4–6 MJ/m³) mainly because:

  1. It contains mostly methane
  2. Its hydrogen content exceeds 80%
  3. It is produced at high pressure
  4. It contains a large fraction of nitrogen from the gasifying air
Answer and working

D. It contains a large fraction of nitrogen from the gasifying air

The combustible components are CO and H2 with some CH4, but air brings in nitrogen, which dilutes the gas along with CO2. Oxygen- or steam-blown gasifiers give richer gas.

Question 7 · hard

A district of 10,000 ha net sown area has 2.0 kW/ha. The target is 4.0 kW/ha, to be met entirely with 35 kW tractors. About how many additional tractors are needed?

  1. 1143 tractors
  2. 58 tractors
  3. 1715 tractors
  4. 572 tractors
Answer and working

D. 572 tractors

Additional power = (4.0 − 2.0) × 10,000 = 20,000 kW; tractors = 20,000/35 = 571.4 → 572. Using the full 4 kW/ha ignores existing power (1143). In practice targets are met with a mix of sources. 58 uses 350 kW per tractor, a factor-of-ten slip (20,000/350 = 57.1); 1715 adds the existing 2.0 kW/ha to the target (60,000/35).

Question 8 · medium

Which is a real limitation of farm power availability (kW/ha) as an indicator of mechanisation?

  1. It cannot be calculated from census data
  2. It excludes tractors and power tillers
  3. It is always expressed per worker, not per hectare
  4. It counts installed rated power, not the hours or load at which machines are actually used
Answer and working

D. It counts installed rated power, not the hours or load at which machines are actually used

Two regions with the same kW/ha can differ widely if one uses machines 1500 h/year and the other 300 h/year. The index also ignores timing, access by small farms and machine condition.

Question 9 · easy

For the same crop (5000 kg/ha grain, 25,000 MJ/ha input), what is the energy productivity?

  1. 5.0 kg/MJ
  2. 0.20 kg/MJ
  3. 2.94 kg/MJ
  4. 200 kg/MJ
Answer and working

B. 0.20 kg/MJ

Energy productivity = product ÷ energy input = 5000/25,000 = 0.20 kg/MJ. Its inverse, 5.0 MJ/kg, is specific energy; 2.94 is the dimensionless energy ratio. 200 kg/MJ is the 0.20 multiplied by 1,000.

Question 10 · medium

Operation-wise mechanisation data show tillage and threshing almost fully mechanised, but rice transplanting and cotton picking largely manual. What use is this for policy?

  1. It shows that the district is fully mechanised and needs no further support
  2. It proves that kW/ha is the only measure that matters
  3. It identifies the operations where research, machinery development and subsidy will do most to raise the overall level
  4. It shows tractors should be removed from tillage
Answer and working

C. It identifies the operations where research, machinery development and subsidy will do most to raise the overall level

An overall index hides gaps. Operation-wise figures show bottlenecks such as transplanting and harvesting where targeted interventions pay off.

A study plan for Farm Power Sources in ASRB NET

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (68% of the 37 questions): Mechanisation indices (12, 32%); Farm power availability (kW/ha) (9, 24%); Biomass and biofuels as power sources (4, 11%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Animal draught power and harnessing (3, 8%); Electrical power on the farm (3, 8%); Mechanical power: engines and tractors (3, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Human power and its limits (2, 5%); Wind power as a farm power source (1, 3%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Electrical power on the farm (2 hard of 3), Human power and its limits (1 hard of 2), Farm power availability (kW/ha) (3 hard of 9).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Mechanisation indices (4 easy of 12); Farm power availability (kW/ha) (3 easy of 9).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ASRB NET Farm Power Sources

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.