LAISHA
Open Laisha

ASRB NET Farm Machinery & Equipment II — Plant Protection, Harvesting, Threshing: practice questions

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering · India · Agricultural Scientists Recruitment Board (ICAR)

Original practice questions written to the published syllabus · not past papers
10worked here, free
43written to this exam in this subject
15syllabus units

About ASRB NET

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering is a specialist certification exam run by Agricultural Scientists Recruitment Board (ICAR), for candidates in India. NET: 150 MCQs, 150 marks, 2 hours, −1/3 per wrong answer, English/Hindi, PG level. Combined NET/ARS/SMS/STO recruitment runs prelims, mains and interview.

Official site: pw.live.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Farm Machinery & Equipment II — Plant Protection, Harvesting, Threshing in ASRB NET

PG-level recall and reasoning on plant protection and harvesting machinery, testing indices, residue management machinery and safety.

Sprayers, weeders, mowers, reapers, combines and threshers: how they work, how to calibrate them and where losses come from.

Our 43 ASRB NET questions in this subject: 2 easy, 22 medium, 19 hard, across 15 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ASRB NET and are not shown on any other exam's page.

Question 1 · hard

Electrostatic spraying improves deposition on the underside of leaves mainly because

  1. charged droplets are larger and resist drift
  2. charge lowers the surface tension of the droplets so they spread wider and wet both leaf surfaces by capillary flow
  3. charged droplets evaporate more slowly
  4. charged droplets induce an opposite charge on the earthed plant and are attracted onto hidden surfaces
Answer and working

D. charged droplets induce an opposite charge on the earthed plant and are attracted onto hidden surfaces

The plant is effectively earthed; a charged droplet induces an image charge and is pulled along field lines, curving round leaves (wrap-around). Charging does not make droplets larger; its effect is strongest on small droplets with a high charge-to-mass ratio.

Question 2 · hard

A granule applicator is calibrated using dry sand instead of the actual granular product. The main problem is that

  1. sand is too heavy for the metering roller
  2. sand damages the delivery tubes
  3. output depends on particle size, density and flowability, so sand output does not predict product output
  4. granules are always metered by volume, so any free-flowing material of any density gives the same kg/ha at one setting
Answer and working

C. output depends on particle size, density and flowability, so sand output does not predict product output

Metering devices deliver a volume that depends on how the particles flow; mass per unit volume differs by material, so calibration must use the product itself. The idea that granules are always metered by volume, so any free-flowing material gives the same kg/ha, is the misconception the question targets.

Question 3 · medium

The cono weeder used in rice has

  1. two conical rotors with serrated strips in tandem and a float
  2. a single rotating flat disc driven by a small petrol engine at high speed
  3. a spring-tine harrow with rubber fingers
  4. a heated plate to scorch weeds
Answer and working

A. two conical rotors with serrated strips in tandem and a float

The cono weeder has two cones set in tandem with opposite orientation, serrated strips that churn soil, and a float that stops it sinking in puddled soil. It is pushed and pulled between rows.

Question 4 · medium

Rolling cultivators with angled spider (star) wheel gangs are used to

  1. cut the standing crop and lay it in windrows ahead of the pick-up baler
  2. level the field after puddling
  3. chop crop residue
  4. throw soil towards or away from the crop row while cutting weeds
Answer and working

D. throw soil towards or away from the crop row while cutting weeds

Angling the gangs lets them move soil sideways, towards the row for earthing up and weed smothering or away from it for early cultivation.

Question 5 · hard

A weeder performance index combines field capacity, plant damage, weeding efficiency and power as

  1. field capacity × plant damage / (weeding efficiency × power)
  2. field capacity × (100 − plant damage) × weeding efficiency / power
  3. weeding efficiency / (field capacity × power)
  4. power × plant damage / field capacity
Answer and working

B. field capacity × (100 − plant damage) × weeding efficiency / power

The index rises with capacity, efficiency and the share of plants left undamaged, and falls with power input, so field capacity × (100 − plant damage) × weeding efficiency / power is the correct form. The others reward damage or penalise capacity.

Question 6 · hard

Oblique (slicing) cutting, where the blade edge moves partly along its own length, is used because it

  1. raises the blade speed without more power
  2. eliminates the need for a sharp edge
  3. reduces the force to start the cut
  4. prevents stems from sliding out of the knife
Answer and working

C. reduces the force to start the cut

A sliding component of motion along the edge reduces the normal force needed to penetrate, as a bread knife shows. Holding the stem in place is the job of serrations, and sharpness still matters.

Question 7 · hard

An operator sets the reel index at 2.2 in a ripe, standing wheat crop that shatters easily. The likely result is

  1. lodged crop feeding better
  2. increased shatter loss at the header as bats strike the heads hard
  3. lower header loss because the crop is swept faster onto the platform
  4. no change because reel speed does not affect losses
Answer and working

B. increased shatter loss at the header as bats strike the heads hard

Too high a reel index beats the heads and knocks grain out; about 1.25–1.5 is commonly recommended, higher only for lodged crop. Reel speed does affect header loss.

Question 8 · hard

A combine working across a steep side slope shows high shoe loss even though settings are correct on level ground. The reason and remedy are

  1. material piles on the downhill side of the shoe; use a levelling shoe or hillside combine
  2. the fan speed drops on slopes as the engine is loaded, so raise the engine speed to full throttle
  3. the cylinder speed rises on slopes; reduce it
  4. walkers stop working on slopes; add a beater
Answer and working

A. material piles on the downhill side of the shoe; use a levelling shoe or hillside combine

Gravity shifts material sideways, overloading one side of the sieves and leaving the other bare. Self-levelling shoes or hillside combines keep the shoe level.

Question 9 · hard

Why is digging potatoes in wet, sticky clay particularly difficult for elevator diggers?

  1. Clay is too hard to penetrate
  2. Tubers float
  3. The haulm grows back
  4. Wet clay does not sieve through the elevator and clings to tubers
Answer and working

D. Wet clay does not sieve through the elevator and clings to tubers

Sticky soil forms a mass that will not fall through the rod gaps, so the elevator is overloaded and separation fails. Dry soil causes the opposite problem of clods.

Question 10 · medium

The fishtail or deflector at the end of a duster delivery tube is used to

  1. spread the dust into a wider, even cloud
  2. meter the dust
  3. agitate the hopper
  4. pressurise the dust
Answer and working

A. spread the dust into a wider, even cloud

It shapes the output. Metering is done by the adjustable orifice at the hopper base.

A study plan for Farm Machinery & Equipment II — Plant Protection, Harvesting, Threshing in ASRB NET

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (47% of the 43 questions): Combine harvester: header, threshing cylinder and concave (4, 9%); Combine separation and cleaning: straw walker and cleaning shoe (4, 9%); Harvesting and threshing losses (4, 9%); Mowers: reciprocating and rotary; mechanics of cutting (4, 9%); Weeders and inter-cultivation equipment (4, 9%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Dusters (3, 7%); Nozzles and droplet spectra (3, 7%); Sprayers: hydraulic, air-assisted and electrostatic (3, 7%); Straw and residue management machines (3, 7%); Threshers (3, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Cotton and sugarcane harvesting (2, 5%); Reapers (2, 5%); Root-crop diggers (2, 5%); Chaff cutters (1, 2%); Sprayer calibration and application rate (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Reapers (2 hard of 2), Sprayer calibration and application rate (1 hard of 1), Sprayers: hydraulic, air-assisted and electrostatic (2 hard of 3).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Nozzles and droplet spectra (1 easy of 3); Mowers: reciprocating and rotary; mechanics of cutting (1 easy of 4).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ASRB NET Farm Machinery & Equipment II — Plant Protection, Harvesting, Threshing

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.