LAISHA
Open Laisha

ASRB NET Machine Design: practice questions

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering · India · Agricultural Scientists Recruitment Board (ICAR)

Original practice questions written to the published syllabus · not past papers
10worked here, free
42written to this exam in this subject
13syllabus units

About ASRB NET

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering is a specialist certification exam run by Agricultural Scientists Recruitment Board (ICAR), for candidates in India. NET: 150 MCQs, 150 marks, 2 hours, −1/3 per wrong answer, English/Hindi, PG level. Combined NET/ARS/SMS/STO recruitment runs prelims, mains and interview.

Official site: pw.live.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Machine Design in ASRB NET

Design principles of farm machinery components, materials of soil-engaging tools, instrumentation (strain gauges, load cells, dynamometers) and overload safety devices.

Sizing the parts of farm machines so they do not fail: shafts, keys, joints, springs, bearings, drives and overload devices.

Our 42 ASRB NET questions in this subject: 22 easy, 14 medium, 6 hard, across 13 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ASRB NET and are not shown on any other exam's page.

Question 1 · easy

The fracture surface of a broken cultivator tine shows smooth curved bands spreading from a point at a weld toe and a small rough zone on the opposite side. What does this indicate?

  1. Failure by creep at high temperature
  2. Brittle fracture caused by low temperature alone
  3. Fatigue failure from the weld toe
  4. A single sudden overload in tension
Answer and working

C. Fatigue failure from the weld toe

Smooth beach marks spreading from an origin show a crack that grew slowly over many load cycles; the rough zone is the final fast fracture of the remaining section. A single overload gives a fibrous or granular surface over the whole section without beach marks. Creep does not occur at field temperatures in steel.

Question 2 · easy

Two shafts are parallel but offset laterally by a few millimetres. Which coupling is designed for this?

  1. Single Hooke's joint
  2. Oldham coupling
  3. Rigid flange coupling
  4. Muff (sleeve) coupling
Answer and working

B. Oldham coupling

The Oldham coupling has a floating centre disc with perpendicular tongues sliding in slots of the two flanges, so it transmits torque between parallel offset shafts. Muff and rigid flange couplings need collinear shafts, and the Hooke's joint is for intersecting axes.

Question 3 · easy

Why is the tractor PTO output shaft made as a splined shaft rather than a plain shaft with a single key?

  1. A splined shaft does not need a guard, because the implement yoke covers the rotating splines
  2. Splines are cheaper to make than a keyway
  3. Splines stop the shaft from bending
  4. Splines carry more torque with less stress concentration and let the yoke slide on and off
Answer and working

D. Splines carry more torque with less stress concentration and let the yoke slide on and off

A splined shaft is in effect many integral keys, sharing the torque and allowing an axial sliding fit, so the implement yoke can be pushed on and locked. Splines do not prevent bending, are more costly to make than a keyway, and every PTO shaft needs a shield regardless.

Question 4 · easy

A bolt of uniform strength has its shank turned down to about the thread root diameter. What is gained?

  1. The shank stretches more, so the bolt absorbs more shock energy and takes a smaller share of fluctuating load
  2. The bolt no longer needs to be preloaded
  3. The threads no longer act as a stress raiser
  4. The bolt becomes stronger in static tension, because the thinner shank work-hardens and raises the proof load of the thread
Answer and working

A. The shank stretches more, so the bolt absorbs more shock energy and takes a smaller share of fluctuating load

Reducing the shank to the root area makes the stress roughly uniform along the bolt and lowers bolt stiffness, so it stores more strain energy before yielding and takes less of the fluctuating load. Static strength is still set by the thread root, and the thread notch remains.

Question 5 · easy

Which weld defect is a groove melted into the base metal along the weld toe and left unfilled?

  1. Lack of penetration at the root
  2. Slag inclusion
  3. Gas porosity
  4. Undercut
Answer and working

D. Undercut

Undercut is a groove at the toe where the arc has melted parent metal that the weld did not refill; it is a sharp notch and a fatigue crack starter. Porosity is gas pockets, slag inclusion is trapped flux, and lack of penetration is an unfused root.

Question 6 · medium

A tractor final-drive pinion shows pitting on the tooth flanks after 1,500 hours, but no tooth has cracked. What does this tell the designer?

  1. The Barth velocity factor was too conservative
  2. The Lewis bending (root) strength was too low, so the tooth roots must be enlarged before fatigue cracks start from the pits
  3. The gear material was too ductile in tension
  4. Surface (contact) fatigue, not bending strength, governs; surface hardness or contact stress must be addressed
Answer and working

D. Surface (contact) fatigue, not bending strength, governs; surface hardness or contact stress must be addressed

Pitting is surface fatigue from repeated Hertzian contact stress, which Buckingham's wear strength (and the AGMA/ISO contact method) addresses; case hardening, a larger pinion or wider face lowers it. Bending failure would show root cracks.

Question 7 · easy

Why is a shear pin designed using the ultimate shear strength of its material rather than an allowable stress with a factor of safety?

  1. Because it is meant to break at a chosen torque, so its breaking strength must be predicted, not kept below
  2. Because a factor of safety would make the pin too small to fit the hub bore, so the drive could not be assembled
  3. Because ultimate strength is always lower than yield strength
  4. Because pins never carry fluctuating loads
Answer and working

A. Because it is meant to break at a chosen torque, so its breaking strength must be predicted, not kept below

A shear pin is a deliberate weak link: it must fail at the set torque to protect the drive. Using allowable stress with a factor of safety would make it stronger than intended, so it would not break when it should. Ultimate strength is higher than yield, not lower.

Question 8 · easy

Which overload protection is most suited to a tine cultivator working in soil with many buried stones?

  1. Spring-trip or hydraulic-reset standards that let each tine ride over the obstacle and return automatically
  2. A friction slip clutch on the tractor PTO
  3. A rigid welded tine with a high factor of safety
  4. Shear bolts on every tine, to be replaced after each strike, since frequent stops let the operator inspect the frame
Answer and working

A. Spring-trip or hydraulic-reset standards that let each tine ride over the obstacle and return automatically

Where obstacles are frequent, automatic-reset devices avoid stopping to replace bolts and protect each tine. Shear bolts suit soils with occasional obstructions. A rigid tine transmits the full impact to the frame. A cultivator is drawn by the drawbar or hitch, not driven by the PTO.

Question 9 · hard

A spring-tine cultivator tine spring is subject to a load that fluctuates between 300 N and 900 N at every stone and clod. Which approach is correct for its design?

  1. Find the mean and alternating shear stresses in the wire, apply the Wahl factor, and check against a fatigue criterion such as Goodman in torsion using the wire's torsional endurance strength
  2. Design only for 900 N with the static shear yield strength
  3. Ignore the curvature factor, because it applies only to static loading
  4. Design for the average load of 600 N with the static shear yield strength
Answer and working

A. Find the mean and alternating shear stresses in the wire, apply the Wahl factor, and check against a fatigue criterion such as Goodman in torsion using the wire's torsional endurance strength

Fluctuating loading needs a fatigue check. The mean load is 600 N and the alternating load 300 N; each gives a stress through tau = K 8PD/(pi d^3), with the Wahl factor (curvature matters most in fatigue). The pair is checked against Goodman or Soderberg in shear. Static checks alone miss fatigue.

Question 10 · hard

Shear pins on a forage harvester feed roll drive sometimes fail after long use at torques below their design breaking torque. What is the most likely mechanism, and what reduces it?

  1. Fatigue of the pin under repeated torque peaks, aggravated by clearance; a tight-fitting pin in hardened bushes and a controlled neck reduce it
  2. The ultimate shear strength rising with use; use a thicker pin
  3. Creep of the steel at harvest temperatures; use a lower-strength pin
  4. Corrosion alone; paint the pin
Answer and working

A. Fatigue of the pin under repeated torque peaks, aggravated by clearance; a tight-fitting pin in hardened bushes and a controlled neck reduce it

Repeated peaks below the breaking torque accumulate fatigue damage, and clearance adds impact and bending. A snug fit in hardened bushes and a consistent reduced section give more repeatable breaking. Creep does not occur in steel at field temperatures, and strength does not increase with use.

A study plan for Machine Design in ASRB NET

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (55% of the 42 questions): Overload safety devices: shear bolts and slip clutches (7, 17%); Rolling and sliding bearings and bearing life (5, 12%); Keys and couplings (4, 10%); Measurement of force, torque and strain on machine elements (4, 10%); Bolted joints (3, 7%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Knuckle and cotter joints (3, 7%); Stress concentration and fatigue (Goodman and Soderberg) (3, 7%); Welded joints (3, 7%); Belt and chain drives (2, 5%); Shafts under combined bending and torsion (2, 5%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Springs (2, 5%); Spur gear design (Lewis and Buckingham) (2, 5%); The design process, materials and factor of safety (2, 5%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Springs (1 hard of 2), Knuckle and cotter joints (1 hard of 3), Stress concentration and fatigue (Goodman and Soderberg) (1 hard of 3).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Keys and couplings (3 easy of 4); Bolted joints (2 easy of 3).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ASRB NET Machine Design

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.