LAISHA
Open Laisha

ASRB NET Engineering Properties of Agricultural Produce: practice questions

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering · India · Agricultural Scientists Recruitment Board (ICAR)

Original practice questions written to the published syllabus · not past papers
10worked here, free
80written to this exam in this subject
10syllabus units

About ASRB NET

ASRB NET — Farm Machinery & Power / Land & Water Management Engineering / Agricultural Structures & Process Engineering is a specialist certification exam run by Agricultural Scientists Recruitment Board (ICAR), for candidates in India. NET: 150 MCQs, 150 marks, 2 hours, −1/3 per wrong answer, English/Hindi, PG level. Combined NET/ARS/SMS/STO recruitment runs prelims, mains and interview.

Official site: pw.live.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Engineering Properties of Agricultural Produce in ASRB NET

Conceptual MCQs on property definitions and measurement methods (platform scale, toluene displacement, air-comparison pycnometer, tilting table, vertical wind tunnel, DSC), and on how properties are used in design of cleaners, bins, dryers and conveyors.

The physical, frictional, aerodynamic, thermal, rheological and electrical properties of grains, fruits and foods that every machine and process is designed around.

Our 80 ASRB NET questions in this subject: 33 easy, 39 medium, 8 hard, across 10 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ASRB NET and are not shown on any other exam's page.

Question 1 · easy

Curray's roundness of a fruit resting in its natural position is calculated as

  1. geometric mean diameter divided by the major diameter, both measured with a vernier calliper on the fruit
  2. radius of the largest inscribed circle multiplied by the number of corners counted on the outline
  3. surface area of the fruit divided by its volume, expressed per millimetre of the fruit's length
  4. projected area of the fruit divided by the area of the smallest circle circumscribing the projection
Answer and working

D. projected area of the fruit divided by the area of the smallest circle circumscribing the projection

Curray's roundness = A_p / A_c. The geometric mean over major diameter is Mohsenin's sphericity, not roundness. Wadell's roundness divides the summed corner radii by N R, rather than multiplying. Surface-to-volume ratio is a different shape index used in heat and mass transfer.

Question 2 · hard

A kernel is treated as a sphere of diameter 5 mm and density 1300 kg/m³ falling in air of density 1.2 kg/m³ with a constant drag coefficient of 0.44 (Newton regime). Its terminal velocity, V_t = [4 g d (ρ_p − ρ_f)/(3 C_d ρ_f)]^(1/2), is

  1. 9.0 m/s
  2. 983 m/s
  3. 0.39 m/s
  4. 12.7 m/s
Answer and working

D. 12.7 m/s

V_t² = 4 × 9.81 × 0.005 × 1298.8 / (3 × 0.44 × 1.2) = 160.9; V_t = 12.7 m/s. 9.0 m/s comes from using 2 instead of 4 in the numerator; 983 m/s applies Stokes' law (air viscosity 1.8 × 10⁻⁵ Pa·s) far outside its Reynolds-number range; 0.39 m/s puts particle density in the denominator instead of air density.

Question 3 · easy

Pneumatic conveying of grain in dilute phase requires that the conveying air velocity be

  1. equal to half the terminal velocity of the grain, so that kernels are not damaged in bends
  2. less than the terminal velocity of the chaff, so that only clean grain is lifted
  3. independent of terminal velocity, since the blower pressure alone carries the grain
  4. greater than the terminal velocity of the grain, with a design margin to prevent settling
Answer and working

D. greater than the terminal velocity of the grain, with a design margin to prevent settling

Kernels stay in suspension only if the air moves faster than their terminal velocity; designers add a margin because bends and particle interactions cause settling. Half the terminal velocity would drop the grain; air slower than the chaff's terminal velocity lifts nothing; pressure without adequate velocity does not keep particles suspended.

Question 4 · easy

The rheological model conventionally used to describe molten chocolate is

  1. Ostwald-de Waele, τ = K γ̇ⁿ
  2. Maxwell, σ = E ε0 exp(−t/λ)
  3. Casson, √τ = √τ0 + √(η_c γ̇)
  4. Newton, τ = μ γ̇ with no yield
Answer and working

C. Casson, √τ = √τ0 + √(η_c γ̇)

The Casson model, with a yield stress and plastic behaviour, is the established model for chocolate. The power law has no yield term; the Maxwell model is a viscoelastic relaxation model, not a flow-curve model; molten chocolate is not Newtonian.

Question 5 · medium

A dough has a relaxation time of 100 s. During 1-second mixing strokes it behaves elastically, but over a 1-hour proof it flows. This is explained by

  1. the Reynolds number, which exceeds 2100 during mixing and falls below it during proofing
  2. the Deborah number λ/t_obs, far above 1 during mixing and far below 1 during proofing
  3. the Biot number, which is high during mixing because of fast heat transfer at the surface
  4. the flow behaviour index n, which changes from below 1 to above 1 as the dough rests
Answer and working

B. the Deborah number λ/t_obs, far above 1 during mixing and far below 1 during proofing

De = 100/1 = 100 during mixing (solid-like) and 100/3600 ≈ 0.03 over the proof (liquid-like). The Reynolds number concerns inertia against viscosity in flow, the Biot number concerns heat-transfer resistances, and a change in n is not what makes dough flow on resting.

Question 6 · easy

On the force-deformation curve of an apple compressed between plates, the bioyield point is where

  1. the skin splits visibly and the force drops sharply towards zero as the whole fruit fails in compression
  2. the curve first leaves the origin and the plates make full contact with the fruit
  3. the slope of the curve is steepest, which gives the apparent modulus of elasticity
  4. deformation increases with no increase or a decrease in force, marking the start of cell rupture
Answer and working

D. deformation increases with no increase or a decrease in force, marking the start of cell rupture

Bioyield is the point of internal failure of cells, reached before the macroscopic rupture point, and it is the practical handling limit. Visible splitting is the rupture point; first contact is the start of the test; the steepest initial slope is used for modulus, not bioyield.

Question 7 · medium

A food has a dielectric constant ε' = 52 and a dielectric loss factor ε'' = 15 at 2450 MHz. Its loss tangent is

  1. 3.467
  2. 0.224
  3. 0.780
  4. 0.288
Answer and working

D. 0.288

tan δ = ε''/ε' = 15/52 = 0.288. 3.467 inverts the ratio; 0.224 divides by the sum; 0.780 multiplies the two, which has no meaning.

Question 8 · medium

Two batches of dried mango differ by ΔL* = −3, Δa* = 4 and Δb* = −12. The total colour difference ΔE = √(ΔL*² + Δa*² + Δb*²) is

  1. 19.0
  2. −11.0
  3. 13.0
  4. 169.0
Answer and working

C. 13.0

ΔE = √(9 + 16 + 144) = √169 = 13.0. 19.0 adds the absolute differences; −11.0 adds the signed differences; 169.0 forgets the square root.

Question 9 · medium

A shelf-stable snack bar has a water activity of 0.83. Using the general minimum water activities for growth given in food microbiology texts, which group is the main spoilage risk?

  1. Moulds, many growing down to about 0.80
  2. Most spoilage bacteria, which grow down to about 0.70
  3. No microbes, since none grow below a_w of 0.90
  4. Yeasts only, since moulds need a_w above 0.95
Answer and working

A. Moulds, many growing down to about 0.80

Most spoilage bacteria need about 0.90–0.91, yeasts about 0.88, and most moulds about 0.80, so at 0.83 moulds are the chief threat. Bacteria do not grow at 0.70; xerophilic moulds and osmophilic yeasts can grow down to about 0.6, so 'no microbes below 0.90' is wrong; moulds tolerate lower a_w than yeasts, not higher. Limits shift with pH, temperature and preservatives.

Question 10 · easy

Which saturated salt solution at 25 °C holds the relative humidity closest to 75% in a desiccator used for isotherm work?

  1. Lithium chloride
  2. Magnesium chloride
  3. Potassium sulfate
  4. Sodium chloride
Answer and working

D. Sodium chloride

Saturated NaCl gives about 75% RH at 25 °C. Lithium chloride gives about 11%, magnesium chloride about 33% and potassium sulfate about 97%; the values change slightly with temperature.

A study plan for Engineering Properties of Agricultural Produce in ASRB NET

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (48% of the 80 questions): Electrical and optical properties (10, 13%); Viscoelastic models (10, 13%); Volume and density: bulk and true (9, 11%); Water activity (9, 11%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Size and shape: sphericity and roundness (8, 10%); Thermal properties: specific heat, conductivity and diffusivity (8, 10%); Aerodynamic properties: terminal velocity (7, 9%); Frictional properties: angle of repose and coefficient of friction (7, 9%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Porosity (6, 8%); Rheology: Newtonian and non-Newtonian flow (6, 8%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Thermal properties: specific heat, conductivity and diffusivity (2 hard of 8), Electrical and optical properties (2 hard of 10), Viscoelastic models (2 hard of 10).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Aerodynamic properties: terminal velocity (4 easy of 7); Size and shape: sphericity and roundness (4 easy of 8).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ASRB NET Engineering Properties of Agricultural Produce

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.