LAISHA
Open Laisha

GATE Engineering Properties of Agricultural Produce: practice questions

GATE — Agricultural Engineering (AG) · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
49written to this exam in this subject
10syllabus units

About GATE

GATE — Agricultural Engineering (AG) is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks (15 General Aptitude + 85 technical: 25 one-mark and 30 two-mark questions). MCQ, MSQ and NAT; negative marking on MCQ only (−1/3 for one-mark, −2/3 for two-mark); no partial credit on MSQ. On-screen virtual calculator.

Source: gate2027.iitm.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Engineering Properties of Agricultural Produce in GATE

Engineering properties is the first line of Section 6 (Agricultural Process Engineering). Expect numerical-answer questions on sphericity and geometric mean diameter, bulk density and porosity, moisture-basis conversion and water removed in drying, and power-law or Bingham flow (apparent viscosity, consistency index from two shear points). Rheology has appeared in about half of the recent papers; water activity and Raoult's law also recur. State the sphericity formula used and carry units through.

The physical, frictional, aerodynamic, thermal, rheological and electrical properties of grains, fruits and foods that every machine and process is designed around.

Our 49 GATE questions in this subject: 6 easy, 22 medium, 21 hard, across 10 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE and are not shown on any other exam's page.

Question 1 · medium

In the platform-scale method, a 175 g orange is pushed fully under water in a beaker on a balance with a thin rod, and the balance reading rises by 182 g. Taking water density as 1000 kg/m³, the density of the orange is

  1. 1040 kg/m³
  2. 175 kg/m³
  3. 962 kg/m³
  4. 490 kg/m³
Answer and working

C. 962 kg/m³

The rise in reading is the mass of water displaced, so volume = 182 cm³ and density = 175 / 182 = 0.962 g/cm³ = 962 kg/m³. 1040 kg/m³ inverts the ratio; 175 kg/m³ confuses the mass in grams with density; 490 kg/m³ adds the two readings, which has no physical basis.

Question 2 · medium

Wheat has a bulk density of 780 kg/m³ and a kernel (true) density of 1290 kg/m³. Its porosity is

  1. 60.5%
  2. 24.6%
  3. 65.4%
  4. 39.5%
Answer and working

D. 39.5%

ε = 1 − ρ_b/ρ_t = 1 − 780/1290 = 0.395, i.e. 39.5%. 60.5% is ρ_b/ρ_t, the solid fraction; 24.6% divides the density difference by the sum of the densities; 65.4% is the void ratio e = ε/(1 − ε), not porosity.

Question 3 · medium

Wheat on a steel chute has a static coefficient of friction of 0.35. Taking the minimum angle at which grain starts to slide from rest as arctan(μ_s), the chute must be inclined at not less than

  1. 20.5°
  2. 19.3°
  3. 20.1°
  4. 70.7°
Answer and working

B. 19.3°

θ = arctan 0.35 = 19.3°. arcsin 0.35 = 20.5° confuses tan with sin; 20.1° treats 0.35 as an angle in radians; 70.7° measures from the vertical. In practice a margin is added for moisture and wear.

Question 4 · medium

A spherical seed of diameter 6 mm is held in an air stream of 10 m/s. With drag coefficient 0.44 and air density 1.2 kg/m³, the drag force F = C_d A ρ V²/2 is

  1. 1.493 mN
  2. 0.746 mN
  3. 2.986 mN
  4. 0.075 mN
Answer and working

B. 0.746 mN

A = π d²/4 = 2.8274e-05 m²; F = 0.44 × 2.8274e-05 × 1.2 × 100 / 2 = 7.464e-04 N = 0.746 mN. 1.493 mN omits the 1/2; 2.986 mN uses π d² as the area; 0.075 mN uses V instead of V².

Question 5 · hard

A 5 mm kernel falls through air at 9 m/s (air density 1.2 kg/m³, viscosity 1.8 × 10⁻⁵ Pa·s). Its particle Reynolds number and flow regime are

  1. 3.0, Stokes regime with drag coefficient 24/Re
  2. 3000000, fully turbulent pipe flow above transition
  3. 3000, Newton regime with nearly constant drag coefficient
  4. 333, intermediate regime between Stokes and Newton
Answer and working

C. 3000, Newton regime with nearly constant drag coefficient

Re = ρ V d/μ = 1.2 × 9 × 0.005 / 1.8 × 10⁻⁵ = 3000, within the Newton range (about 1000 to 2 × 10⁵), where C_d is nearly constant. 3.0 comes from entering viscosity in mPa·s as if it were Pa·s; 3000000 enters the diameter in mm; 333 omits the velocity. Pipe-flow regime language does not apply to a falling particle.

Question 6 · medium

A tomato concentrate follows the power law τ = K γ̇ⁿ with K = 8.5 Pa·sⁿ and n = 0.35. Its apparent viscosity at a shear rate of 100 s⁻¹ is

  1. 42.6 Pa·s
  2. 1.696 Pa·s
  3. 0.426 Pa·s
  4. 0.085 Pa·s
Answer and working

C. 0.426 Pa·s

η_a = K γ̇^(n−1) = 8.5 × 100^(−0.65) = 0.426 Pa·s. 42.6 is the shear stress τ in Pa, not a viscosity; 1.696 uses exponent −n instead of n − 1; 0.085 divides K by γ̇, valid only for n = 0.

Question 7 · hard

A juice concentrate has a viscosity of 12.0 mPa·s at 20 °C and an Arrhenius flow activation energy of 25 kJ/mol, η = A exp(E_a/RT). Its viscosity at 60 °C is

  1. 0.00 mPa·s
  2. 3.50 mPa·s
  3. 41.1 mPa·s
  4. 4.00 mPa·s
Answer and working

B. 3.50 mPa·s

η2 = 12.0 × exp[(25000/8.314)(1/333.15 − 1/293.15)] = 12.0 × exp(−1.2316) = 3.50 mPa·s. Using Celsius temperatures sends the exponent to an absurd value and gives effectively zero (0.00); reversing the sign gives a rise to 41.1 mPa·s, the wrong direction; scaling by 20/60 assumes inverse proportionality to °C, which has no basis. That scaling gives 12.0 × 20/60 = 4.00 mPa·s.

Question 8 · hard

A food with loss factor ε'' = 12 is heated at 2450 MHz in a field of 1500 V/m (rms). Using P = 2π f ε0 ε'' E² with ε0 = 8.854 × 10⁻¹² F/m, the power absorbed per unit volume is

  1. 0.586 MW/m³
  2. 0.00245 MW/m³
  3. 3.68 MW/m³
  4. 3680 MW/m³
Answer and working

C. 3.68 MW/m³

P = 2π × 2.45 × 10⁹ × 8.854 × 10⁻¹² × 12 × 1500² = 3.6800e+06 W/m³ = 3.68 MW/m³. 0.586 omits 2π; 0.00245 uses E instead of E²; 3680 is a kW–MW slip.

Question 9 · medium

Fresh carrot has a moisture content of 150% dry basis. Its moisture content on wet basis is

  1. 150.0%
  2. 60.0%
  3. 40.0%
  4. 66.7%
Answer and working

B. 60.0%

M_wb = M_db/(1 + M_db) = 1.5/2.5 = 0.600, i.e. 60.0%. 150.0% is impossible on wet basis; 40.0% is the dry-matter fraction; 66.7% is 1/1.5, the reciprocal of dry basis.

Question 10 · medium

At a fixed relative humidity of the drying air, raising the air temperature changes the equilibrium moisture content of grain in which direction?

  1. It raises the EMC, so warmer air at the same RH leaves the grain wetter at equilibrium
  2. It leaves the EMC unchanged, since EMC depends on relative humidity alone
  3. It lowers the EMC, so warmer air at the same RH dries grain to a lower final moisture
  4. It raises the EMC above 100% dry basis whenever the air exceeds 60 °C
Answer and working

C. It lowers the EMC, so warmer air at the same RH dries grain to a lower final moisture

Isotherms shift downward as temperature rises, so EMC at a given RH falls; ASABE equilibrium-moisture equations include temperature for this reason. The reverse is the common slip; RH alone does not fix EMC; and grain does not exceed 100% dry basis at high temperature.

A study plan for Engineering Properties of Agricultural Produce in GATE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (55% of the 49 questions): Rheology: Newtonian and non-Newtonian flow (8, 16%); Water activity (8, 16%); Thermal properties: specific heat, conductivity and diffusivity (6, 12%); Aerodynamic properties: terminal velocity (5, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Size and shape: sphericity and roundness (5, 10%); Viscoelastic models (5, 10%); Frictional properties: angle of repose and coefficient of friction (4, 8%); Porosity (4, 8%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Electrical and optical properties (3, 6%); Volume and density: bulk and true (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Electrical and optical properties (2 hard of 3), Rheology: Newtonian and non-Newtonian flow (5 hard of 8), Aerodynamic properties: terminal velocity (3 hard of 5).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Thermal properties: specific heat, conductivity and diffusivity (3 easy of 6); Size and shape: sphericity and roundness (1 easy of 5).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE Engineering Properties of Agricultural Produce

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.