LAISHA
Open Laisha

GATE Farm Machinery & Equipment I — Tillage, Sowing, Planting, Fertiliser: practice questions

GATE — Agricultural Engineering (AG) · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
44written to this exam in this subject
14syllabus units

About GATE

GATE — Agricultural Engineering (AG) is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks (15 General Aptitude + 85 technical: 25 one-mark and 30 two-mark questions). MCQ, MSQ and NAT; negative marking on MCQ only (−1/3 for one-mark, −2/3 for two-mark); no partial credit on MSQ. On-screen virtual calculator.

Source: gate2027.iitm.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Farm Machinery & Equipment I — Tillage, Sowing, Planting, Fertiliser in GATE

Numerical answer and MCQ items on seed-drill, planter and fertiliser-drill calibration (one of the most often repeated topics), rotary-tiller bite length, mouldboard plough draft and power, offset disc harrow force balance, field capacity, and machinery cost by straight-line, declining-balance and sum-of-years-digits depreciation with break-even custom hire.

Machines that prepare the seedbed and put seed and fertiliser in the ground, and how to calibrate and cost them.

Our 44 GATE questions in this subject: 8 easy, 29 medium, 7 hard, across 14 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE and are not shown on any other exam's page.

Question 1 · hard

A mounted mouldboard plough keeps rising out of work in firm soil even with the hydraulic set deep. Which fault is the most likely mechanical cause?

  1. Forward speed slightly lower than usual
  2. Too much horizontal suction
  3. Worn shares that have lost their vertical suction
  4. Mouldboards polished by scouring
Answer and working

C. Worn shares that have lost their vertical suction

Worn share points lose the downward suction that pulls the bottom in, and the plough floats out. A small change in speed does not make a plough float out; polished mouldboards help scouring, and horizontal suction affects width, not depth.

Question 2 · medium

Chisel shanks set too far apart for their working depth will most likely

  1. invert the soil completely
  2. reduce the draft to zero
  3. leave ridges of untilled soil between the shanks
  4. cause the plough to run shallower than set, since the soil lifts the frame
Answer and working

C. leave ridges of untilled soil between the shanks

The loosened zones from adjacent shanks must meet below the surface. If spacing is too large for the depth, untilled ridges remain between shanks.

Question 3 · medium

A tractor with a 2.0 m wheelbase exerts a horizontal drawbar pull of 12 kN at a drawbar height of 0.5 m. What weight is transferred from the front to the rear axle (simple static approximation)?

  1. 48 kN
  2. 3.0 kN
  3. 6.0 kN·m
  4. 9.0 kN
Answer and working

B. 3.0 kN

Taking moments about the rear wheel contact: ΔW = P·h/L = 12 × 0.5 / 2.0 = 3.0 kN. Inverting the ratio gives 48 kN; multiplying P by h alone gives 6.0 kN·m, a moment, not a force; using (L − h) as the arm gives 9.0 kN.

Question 4 · medium

In a horizontal-plate planter, what is the function of the spring-loaded cut-off?

  1. Push the seed out of the cell into the tube
  2. Drive the plate from the ground wheel
  3. Cover the seed in the furrow
  4. Remove excess seeds so each cell carries one seed
Answer and working

D. Remove excess seeds so each cell carries one seed

The cut-off wipes surplus seeds from the cell; the knock-out or ejector pushes the seed from the cell into the tube.

Question 5 · medium

A planter's ground wheel is 50 cm in diameter and drives a 12-cell plate at 0.5 plate turns per wheel turn. Ignoring skid, what is seed spacing?

  1. 6.54 cm
  2. 13.09 cm
  3. 8.33 cm
  4. 26.18 cm
Answer and working

D. 26.18 cm

Spacing = πD/(i·N) = π × 0.5/(0.5 × 12) = 0.2618 m = 26.18 cm. Multiplying by i gives 6.54 cm; ignoring the drive ratio gives 13.09 cm; leaving out π (using D as the travel per turn) gives 8.33 cm.

Question 6 · medium

Which opener is best suited to sowing through heavy surface residue?

  1. Double-disc opener
  2. Shoe opener
  3. Hoe opener without coulter
  4. Runner opener
Answer and working

A. Double-disc opener

Discs cut through residue instead of dragging it; tined, hoe and shoe openers bunch residue and block.

Question 7 · medium

Why must adjacent passes of a spinning-disc broadcaster overlap?

  1. To reduce the application rate
  2. Because the disc speed varies with engine load, so each pass throws a different width
  3. To stop segregation
  4. The spread pattern tapers toward the edges, so overlap evens out the total
Answer and working

D. The spread pattern tapers toward the edges, so overlap evens out the total

A single-pass pattern is heaviest in the centre and thins at the edges; spacing passes at the correct bout width overlaps the tails to give even coverage.

Question 8 · medium

How many turns of a 1.2 m diameter drive wheel are needed to simulate 1/25 ha with an 11-row drill at 20 cm spacing, taking effective travel per turn as πD(1 − 0.05)?

  1. 48.2
  2. 101.5
  3. 558
  4. 50.8
Answer and working

D. 50.8

Width = 11 × 0.2 = 2.2 m. Travel per turn = π × 1.2 × 0.95 = 3.581 m. Area per turn = 7.879 m². N = 400/7.879 = 50.8 turns. Ignoring skid gives 48.2; using one row gives 558. 101.5 uses the 1.2 m as a radius (π × 0.6 × 0.95).

Question 9 · hard

A farm must sow 40 ha within 10 days of 8 working hours each, at 5 km/h and 80 % field efficiency. What minimum effective width is needed?

  1. 0.125 m
  2. 1.00 m
  3. 1.25 m
  4. 10.0 m
Answer and working

C. 1.25 m

Hours = 80. Required EFC = 40/80 = 0.5 ha/h. w = 10 × 0.5/(5 × 0.8) = 1.25 m. Omitting the factor 10 gives 0.125 m; ignoring efficiency gives 1.00 m.

Question 10 · medium

Owning a zero-till drill costs 60 000 per year fixed plus 900 per hectare variable. Custom hire costs 2400 per hectare. Above what annual area is owning cheaper?

  1. 25 ha
  2. 66.7 ha
  3. 18.2 ha
  4. 40 ha
Answer and working

D. 40 ha

Break-even area = FC/(custom rate − VC) = 60 000/(2400 − 900) = 40 ha. Ignoring variable cost gives 25 ha; adding VC to the hire rate gives 18.2 ha. 66.7 ha divides by the variable cost alone (60 000/900).

A study plan for Farm Machinery & Equipment I — Tillage, Sowing, Planting, Fertiliser in GATE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (59% of the 44 questions): Forces on tillage tools, draft and hitching (7, 16%); Cost analysis of implements (6, 14%); Calibration of seed drills (5, 11%); Field capacity and field efficiency (4, 9%); Seed-metering mechanisms: fluted roller, cup, plate and pneumatic (4, 9%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Fertiliser distributors (3, 7%); Harrows, cultivators and rotavators (3, 7%); Seed drills and planters (3, 7%); Disc plough (2, 5%); Mouldboard plough (2, 5%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Paddy and vegetable transplanters (2, 5%); Chisel plough and subsoiler (1, 2%); Furrow geometry (1, 2%); Furrow openers (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Mouldboard plough (1 hard of 2), Seed drills and planters (1 hard of 3), Field capacity and field efficiency (1 hard of 4).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Paddy and vegetable transplanters (1 easy of 2); Cost analysis of implements (2 easy of 6).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE Farm Machinery & Equipment I — Tillage, Sowing, Planting, Fertiliser

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.