LAISHA
Open Laisha

Nepal Engineering Council Registration Exam Farm Machinery & Equipment I — Tillage, Sowing, Planting, Fertiliser: practice questions

Nepal Engineering Council Registration Exam — Agricultural Engineering · Nepal · Nepal Engineering Council

Original practice questions written to the published syllabus · not past papers
10worked here, free
27written to this exam in this subject
15syllabus units

About Nepal Engineering Council Registration Exam

Nepal Engineering Council Registration Exam — Agricultural Engineering is a licensing and registration exam run by Nepal Engineering Council, for candidates in Nepal.

Official site: nec.gov.np.

We have not been able to confirm these details against the exam body's own specification, so fees, dates and pass marks are left out on purpose. Check the current format, eligibility, fees and dates on the official site.

Farm Machinery & Equipment I — Tillage, Sowing, Planting, Fertiliser in Nepal Engineering Council Registration Exam

Machines that prepare the seedbed and put seed and fertiliser in the ground, and how to calibrate and cost them.

Our 27 Nepal Engineering Council Registration Exam questions in this subject: 18 easy, 9 medium, 0 hard, across 15 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Nepal Engineering Council Registration Exam and are not shown on any other exam's page.

Question 1 · easy

Which operation is classed as primary tillage?

  1. Mouldboard ploughing after harvest
  2. Spike-tooth harrowing after ploughing
  3. Planking to crush clods before sowing
  4. Inter-row weeding with a sweep cultivator
Answer and working

A. Mouldboard ploughing after harvest

Primary tillage is the first, deeper operation that cuts and inverts or shatters the soil, done with mouldboard, disc or chisel ploughs. Harrowing and planking are secondary tillage that refine the seedbed, and inter-row weeding after emergence is inter-cultivation.

Question 2 · medium

When a field is ploughed with a one-way mouldboard plough by the casting method, what is left in the centre of each land?

  1. A raised back furrow
  2. A dead furrow
  3. A headland ridge
  4. No furrow mark
Answer and working

B. A dead furrow

Casting starts at the edges and works inward, throwing slices outward, so the last pass leaves an open dead furrow in the middle. Gathering starts in the centre and makes a back furrow. Only a reversible plough leaves no marks.

Question 3 · easy

Draft of a tillage implement is defined as

  1. the horizontal component of the pull parallel to the direction of travel
  2. the total resultant soil force acting on the implement, whatever its direction
  3. the vertical component of the pull
  4. the side force on the landside
Answer and working

A. the horizontal component of the pull parallel to the direction of travel

Draft is the horizontal component along the line of travel. The resultant also has vertical and side components.

Question 4 · easy

The vertical uncut face of soil left beside a mouldboard plough furrow is the

  1. furrow sole
  2. crown
  3. back furrow
  4. furrow wall
Answer and working

D. furrow wall

The furrow wall is the vertical face, the sole is the bottom of the furrow and the crown is the top of the inverted slice.

Question 5 · easy

In a cup-feed seed meter, seeds are lifted from the hopper by

  1. a vacuum
  2. cups or spoons on the rim of a rotating vertical disc
  3. a fluted roller
  4. an auger
Answer and working

B. cups or spoons on the rim of a rotating vertical disc

Cups on a rotating disc scoop seeds and drop them into funnels leading to the seed tubes.

Question 6 · easy

Which furrow opener is typical of zero-till wheat drills sown after rice in the Indo-Gangetic plains?

  1. Shoe (runner)
  2. Mouldboard bottom
  3. Inverted-T tine
  4. Spike tooth
Answer and working

C. Inverted-T tine

The inverted-T opener cuts a narrow slot with a wider base, disturbing little soil; it is the standard zero-till opener in that region.

Question 7 · medium

The most common field-preparation cause of missing and buried hills with a rice transplanter is

  1. too-dense mat nursery
  2. poorly levelled or unsettled puddle
  3. low engine speed
  4. narrow row spacing
Answer and working

B. poorly levelled or unsettled puddle

Unlevel fields give uneven water and soil depth, so the fork plants too deep in low spots and misses in high spots; an unsettled puddle lets seedlings sink or float.

Question 8 · easy

Which of the following is a variable (operating) cost of a machine?

  1. Fuel
  2. Depreciation from obsolescence
  3. Insurance
  4. Housing
Answer and working

A. Fuel

Fuel and lubricant costs rise with hours of use. Insurance and housing are fixed ownership costs; obsolescence-driven depreciation occurs even without use. Lubricant cost behaves the same way.

Question 9 · medium

Why do plate planters give best results with graded seed?

  1. Graded seed germinates faster
  2. Cells are sized for one seed of a given size; mixed sizes cause misses and doubles
  3. The cut-off works only with large seed, so small seeds slip through unmetered
  4. Grading removes the need for calibration, because every seed then has the same mass
Answer and working

B. Cells are sized for one seed of a given size; mixed sizes cause misses and doubles

Seeds too big fail to enter the cell (misses) and small ones enter in pairs (doubles); grading matches seed to the cell.

Question 10 · easy

In a mat-type rice transplanter, the hill spacing along the row is changed by

  1. changing the row spacing
  2. raising the floats
  3. changing the number of seedlings per hill picked by the fork, which spreads the hills
  4. changing the ratio of planting-arm speed to forward travel with a gear lever
Answer and working

D. changing the ratio of planting-arm speed to forward travel with a gear lever

The planting mechanism is geared to travel; a different ratio gives more or fewer hills per metre. Row spacing is fixed by design.

A study plan for Farm Machinery & Equipment I — Tillage, Sowing, Planting, Fertiliser in Nepal Engineering Council Registration Exam

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (52% of the 27 questions): Mouldboard plough (4, 15%); Paddy and vegetable transplanters (3, 11%); Seed-metering mechanisms: fluted roller, cup, plate and pneumatic (3, 11%); Disc plough (2, 7%); Furrow geometry (2, 7%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Furrow openers (2, 7%); Harrows, cultivators and rotavators (2, 7%); Objectives and types of tillage (2, 7%); Calibration of seed drills (1, 4%); Chisel plough and subsoiler (1, 4%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Cost analysis of implements (1, 4%); Fertiliser distributors (1, 4%); Field capacity and field efficiency (1, 4%); Forces on tillage tools, draft and hitching (1, 4%); Seed drills and planters (1, 4%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Bank the easy marks: Harrows, cultivators and rotavators (2 easy of 2); Calibration of seed drills (1 easy of 1).

    Do these early in revision so they are fast on the day.

  5. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Nepal Engineering Council Registration Exam Farm Machinery & Equipment I — Tillage, Sowing

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.