LAISHA
Open Laisha

Agricultural and Biosystems Engineers Licensure Examination Farm Machinery & Equipment I — Tillage, Sowing, Planting, Fertiliser: practice questions

Agricultural and Biosystems Engineers Licensure Examination (ABELE) · Philippines · Professional Regulatory Board of Agricultural and Biosystems Engineering, PRC

Original practice questions written to the published syllabus · not past papers
10worked here, free
41written to this exam in this subject
15syllabus units

About Agricultural and Biosystems Engineers Licensure Examination

Agricultural and Biosystems Engineers Licensure Examination (ABELE) is a licensing and registration exam run by Professional Regulatory Board of Agricultural and Biosystems Engineering, PRC, for candidates in Philippines. Paper-based, 2 days (Day 1 6 hours; Day 2 5 hours + 4 hours). Non-programmable calculator only; the Dec 2025 programme bans the Casio fx-991ES/ES Plus by name.

Source: prc.gov.ph.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Farm Machinery & Equipment I — Tillage, Sowing, Planting, Fertiliser in Agricultural and Biosystems Engineers Licensure Examination

Machines that prepare the seedbed and put seed and fertiliser in the ground, and how to calibrate and cost them.

Our 41 Agricultural and Biosystems Engineers Licensure Examination questions in this subject: 16 easy, 20 medium, 5 hard, across 15 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to Agricultural and Biosystems Engineers Licensure Examination and are not shown on any other exam's page.

Question 1 · medium

Why is a reversible (two-way) mouldboard plough preferred on sloping and irrigated land?

  1. It needs much less draft per bottom than a one-way plough of the same width of cut
  2. It does not need a landside
  3. It inverts the slice more completely than any one-way bottom, burying all residue on slopes
  4. All slices are thrown one way across the field, so no back or dead furrows are formed
Answer and working

D. All slices are thrown one way across the field, so no back or dead furrows are formed

Flipping at each headland keeps the slices going the same direction, leaving the field level without back and dead furrows, which matters for irrigation and on slopes. Draft per bottom is similar, and each bottom still has a landside.

Question 2 · medium

A 3-bottom mouldboard plough cuts 30 cm per bottom at 20 cm depth in soil with a unit draft of 7 N/cm². It is pulled at 5 km/h. What drawbar power is needed?

  1. 63.0 kW
  2. 17.5 kW
  3. 5.83 kW
  4. 175 kW
Answer and working

B. 17.5 kW

Draft = bottoms × width × depth × unit draft = 3 × 30 × 20 × 7 = 12,600 N. Speed = 5/3.6 = 1.389 m/s. Power = 12,600 × 1.389 = 17,500 W = 17.5 kW. Multiplying by 5 without converting km/h gives 63.0 kW; using one bottom gives 5.83 kW. 175 kW is a factor-of-ten slip.

Question 3 · easy

Tractor hydraulic draft control acts to

  1. hold the implement at a fixed height relative to the tractor regardless of draft
  2. lock the differential
  3. change the PTO speed
  4. keep implement draft nearly constant by raising or lowering it
Answer and working

D. keep implement draft nearly constant by raising or lowering it

Draft control senses force in the links and adjusts implement depth to keep draft steady. Position control holds a fixed height.

Question 4 · medium

In a mat-type rice transplanter, the number of seedlings per hill is adjusted by

  1. the forward speed of the tractor relative to the picking fork
  2. the float height
  3. the row spacing, which can be changed by moving the planting arms
  4. the lateral shift of the tray and the vertical feed of the mat
Answer and working

D. the lateral shift of the tray and the vertical feed of the mat

The block picked is set by the tray's sideways step and the downward mat feed. Forward speed and gear change hill spacing; row spacing is fixed.

Question 5 · medium

A 6-row walk-behind rice transplanter at 30 cm row spacing moves at 2 km/h with 70 % field efficiency. What is its effective field capacity?

  1. 0.252 ha/h
  2. 0.36 ha/h
  3. 2.52 ha/h
  4. 0.042 ha/h
Answer and working

A. 0.252 ha/h

Width = 6 × 0.30 = 1.8 m. TFC = 1.8 × 2/10 = 0.36 ha/h. EFC = 0.36 × 0.7 = 0.252 ha/h. Forgetting efficiency gives 0.36; omitting the /10 gives 2.52; using one row gives 0.042.

Question 6 · medium

In a transplanter field test, 18 of 400 expected hill positions had no seedlings. What is the missing-hill percentage?

  1. 18 %
  2. 0.45 %
  3. 95.5 %
  4. 4.5 %
Answer and working

D. 4.5 %

Missing hills = 18/400 × 100 = 4.5 %. 95.5 % is the percentage of filled hills, and 0.45 % is a decimal slip.

Question 7 · easy

How many hours will a machine with an effective field capacity of 0.6 ha/h take to cover 60 ha?

  1. 36 h
  2. 10 h
  3. 100 h
  4. 0.01 h
Answer and working

C. 100 h

Time = area/EFC = 60/0.6 = 100 h. 36 comes from multiplying the numbers. 10 h reads 0.6 ha/h as 6 ha/h; 0.01 h inverts the ratio.

Question 8 · hard

A calibrated drill sows 12 % more seed per hectare in the field than in the stationary test. Which explanation is most consistent?

  1. The drive wheel turns more per metre than assumed (less skid, smaller rolling radius) or vibration raises flow
  2. The seed is lighter (lower test weight) in the field
  3. The row spacing is wider in the field than in the test, so each row must deliver 12 % more seed to cover the area
  4. The hopper is fuller in the field only
Answer and working

A. The drive wheel turns more per metre than assumed (less skid, smaller rolling radius) or vibration raises flow

More seed per area means more meter turns per metre or more flow per turn: a smaller effective rolling radius from sinkage, less skid than assumed, or vibration. A field check over a measured run reveals it.

Question 9 · medium

On a mounted plough, the fore-and-aft level (so front and rear bottoms cut the same depth) is set with the

  1. levelling lift rod
  2. top link
  3. check chain
  4. PTO shaft
Answer and working

B. top link

Lengthening or shortening the top link pitches the plough; the lift rod levels it sideways; check chains control sway.

Question 10 · hard

A custom-hire operator must sow wheat into loose rice straw after combine harvest without burning. Which machine choice is most appropriate?

  1. A conventional tined drill after burning the straw
  2. A spinning-disc broadcaster with no incorporation
  3. A mouldboard plough followed by a runner-opener drill in the same day to bury all the straw
  4. A disc or rotary zero-till drill that cuts or clears straw ahead of the openers
Answer and working

D. A disc or rotary zero-till drill that cuts or clears straw ahead of the openers

Loose straw blocks tined openers; straw-managing zero-till drills cut or clear straw so the openers can place seed, allowing sowing without burning. Burning is what such drills were developed to avoid.

A study plan for Farm Machinery & Equipment I — Tillage, Sowing, Planting, Fertiliser in Agricultural and Biosystems Engineers Licensure Examination

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (49% of the 41 questions): Cost analysis of implements (5, 12%); Field capacity and field efficiency (4, 10%); Forces on tillage tools, draft and hitching (4, 10%); Paddy and vegetable transplanters (4, 10%); Fertiliser distributors (3, 7%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Mouldboard plough (3, 7%); Seed drills and planters (3, 7%); Calibration of seed drills (2, 5%); Chisel plough and subsoiler (2, 5%); Disc plough (2, 5%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Furrow geometry (2, 5%); Furrow openers (2, 5%); Harrows, cultivators and rotavators (2, 5%); Objectives and types of tillage (2, 5%); Seed-metering mechanisms: fluted roller, cup, plate and pneumatic (1, 2%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Field capacity and field efficiency (2 hard of 4), Calibration of seed drills (1 hard of 2), Seed drills and planters (1 hard of 3).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Harrows, cultivators and rotavators (2 easy of 2); Field capacity and field efficiency (2 easy of 4).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — Agricultural and Biosystems Engineers Licensure Examination Farm Machinery & Equipment I —

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.