Agricultural and Biosystems Engineers Licensure Examination (ABELE) · Philippines · Professional Regulatory Board of Agricultural and Biosystems Engineering, PRC
Original practice questions written to the published syllabus · not past papersAgricultural and Biosystems Engineers Licensure Examination (ABELE) is a licensing and registration exam run by Professional Regulatory Board of Agricultural and Biosystems Engineering, PRC, for candidates in Philippines. Paper-based, 2 days (Day 1 6 hours; Day 2 5 hours + 4 hours). Non-programmable calculator only; the Dec 2025 programme bans the Casio fx-991ES/ES Plus by name.
Source: prc.gov.ph.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Designing and evaluating sprinkler and drip systems, from emitter hydraulics to pump selection.
Our 45 Agricultural and Biosystems Engineers Licensure Examination questions in this subject: 30 easy, 15 medium, 0 hard, across 14 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to Agricultural and Biosystems Engineers Licensure Examination and are not shown on any other exam's page.
A centre pivot irrigates a full circle inscribed in a square field with no corner arm or end gun. What fraction of the square is irrigated?
C. About 78.5 % (π/4)
Circle area πr² divided by square area (2r)² = π/4 ≈ 0.785. 2/π (63.7 %) confuses the area ratio with a different circle constant; the corners (about 21.5 %) stay dry unless a corner system or end gun is used. 100 % ignores the dry corners; 50 % treats the circle as half the square.
A centre pivot lateral is 400 m long from pivot to the last sprinkler (no end gun). What area does it irrigate?
B. 50.3 ha
Area = πr² = π × 400² = 502655 m² = 50.3 ha. 64.0 ha is the enclosing square (800 m × 800 m); 16.0 ha is 400 m × 400 m; 12.6 ha treats 400 m as the diameter.
What value of Christiansen's uniformity coefficient indicates perfectly uniform application?
B. 100 %
If every can catches the mean depth, the sum of absolute deviations is zero and CU = 100 %. 85 % is a commonly cited design target for high-value crops, not the ideal. 0 % and 50 % have no special meaning for CU; 0 % would require deviations as large as the mean.
Where on a pressurised mainline should combination air-release and vacuum-relief valves be installed?
A. At high points and at the pump discharge
Air collects at high points and must be released during filling and operation; vacuum relief at high points prevents pipe collapse and suction when the line drains. Low points get drain valves instead.
Christiansen's rule limits pressure variation along a sprinkler lateral to about 20 % of the operating pressure. What discharge variation does this correspond to?
B. About 10 %
Nozzle discharge varies with the square root of pressure, so a 20 % pressure change gives about √1.2 − 1 ≈ 9.5 % (or 1 − √0.8 ≈ 10.6 %) change, i.e. about 10 %. 20 % would be true only if discharge were proportional to pressure. 40 % doubles the pressure variation instead of roughly halving it; 4 % squares the 20 % fraction (0.2² = 0.04).
An emitter discharges 2.0 L/h at 100 kPa and 2.2 L/h at 150 kPa. What is its discharge exponent x?
B. 0.235
x = ln(q1/q2)/ln(h1/h2) = ln(2.2/2.0)/ln(150/100) = 0.0953/0.4055 = 0.235. 0.200 is the ratio of percentage changes (10 %/50 %), a linear approximation that is poor for a 50 % change; 4.25 inverts the ratio. 0.500 simply assumes a fully turbulent emitter.
Which filter is effective for removing sand from well water but ineffective against algae and organic matter?
B. Hydrocyclone (centrifugal sand separator)
A hydrocyclone separates particles denser than water by centrifugal action; algae and organic matter have densities close to water and pass through. Media filters are preferred for organic loads.
Approximately what opening size corresponds to a 120-mesh screen?
D. About 125 µm
120 mesh (120 openings per inch) has openings of about 0.125 mm = 125 µm. About 75 µm corresponds to 200 mesh. About 1.20 mm and about 12 µm are factor-of-ten slips.
When should a drip system filter be backflushed or cleaned?
B. When pressure drop rises
Filters are cleaned on a pressure-differential criterion read from gauges or a differential switch (or on a timer). Waiting for emitter clogging means the filter has already failed.
A common rule for selecting filtration fineness for drip emitters is that the filter should remove particles:
C. Several times smaller than the smallest emitter passage, per the maker
Particles smaller than the passage can still bridge and aggregate, so filters are chosen several times finer than the passage (sources quote fractions from about one-quarter to one-tenth); the manufacturer's recommendation governs.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.