BCS Agriculture cadre — Agricultural Engineering (subject code 821) · Bangladesh · Bangladesh Public Service Commission
Original practice questions written to the published syllabus · not past papersBCS Agriculture cadre — Agricultural Engineering (subject code 821) is a government recruitment exam run by Bangladesh Public Service Commission, for candidates in Bangladesh. Preliminary 200-mark MCQ (2 h); written 900 marks; viva 200 marks. Code 821 is a 200-mark post-related paper.
Source: bpsc.gov.bd.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Designing and evaluating sprinkler and drip systems, from emitter hydraulics to pump selection.
Our 45 BCS Agriculture cadre questions in this subject: 30 easy, 15 medium, 0 hard, across 14 units.
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
Sprinklers discharging 0.5 L/s each are spaced 12 m along the lateral and 18 m between laterals. What is the average application rate?
D. 8.33 mm/h
I = 3600 q / (Sl × Sm) = 3600 × 0.5 / (12 × 18) = 8.33 mm/h (1 L over 1 m² is 1 mm). Using 1000 instead of 3600 (treating L/s as m³/h) gives 2.31; adding the spacings instead of multiplying gives 60; using 12 m × 12 m gives 12.5.
A soil has a basic infiltration rate of 10 mm/h. Sprinklers are to be set on a 12 m × 12 m square grid. What is the largest sprinkler discharge that avoids ponding?
C. 0.40 L/s
q = I × Sl × Sm = 10 mm/h × 144 m² = 1440 L/h = 0.40 L/s. 1.44 is the answer in m³/h mistakenly labelled L/s; the other options are factor-of-ten slips.
Using Christiansen's formula with m = 1.852, what is the F factor for a lateral with 10 outlets, the first a full spacing from the inlet?
A. 0.402
F = 1/(m+1) + 1/(2N) + √(m−1)/(6N²) = 0.3506 + 0.0500 + 0.0015 = 0.402. 0.351 is the limit for very many outlets; 0.452 uses 1/N instead of 1/(2N); 0.5 is a guess from the average of full and zero flow.
Drip laterals are most commonly made of which material?
B. Polyethylene
Laterals are flexible polyethylene tubing (commonly LLDPE/LDPE blends) because it is cheap, flexible, resistant to fertilisers and allows emitters to be inserted or moulded in. Aluminium is used for portable sprinkler laterals; PVC is common for buried mains.
Which international standard specifies requirements and test methods for irrigation emitters and emitting pipe?
C. ISO 9261
ISO 9261 covers emitters and emitting pipe (including limits on the coefficient of variation and deviation from nominal flow). ISO 9001 is quality management, ISO 14001 environmental management and ISO 5725 measurement accuracy.
An emitter exponent x = 1.0 indicates which flow regime?
A. Fully laminar flow
Laminar flow through a long, fine passage makes discharge proportional to head (x = 1). Fully turbulent orifice flow gives x = 0.5, vortex emitters about 0.4, and pressure-compensating emitters approach zero.
Which filter is effective for removing sand from well water but ineffective against algae and organic matter?
B. Hydrocyclone (centrifugal sand separator)
A hydrocyclone separates particles denser than water by centrifugal action; algae and organic matter have densities close to water and pass through. Media filters are preferred for organic loads.
Up to roughly what soil water suction does a standard tensiometer give reliable readings?
C. About 80–85 kPa
A tensiometer's water column breaks (air enters through the porous cup) at around 80–85 kPa suction, so it covers the wet range important for frequently irrigated crops. 1500 kPa is the wilting point, beyond its range; 33 kPa (not 330) is field capacity for medium soils. About 10 kPa is a wet-soil reading well inside the working range, not its limit.
What does the economic pipe size minimise?
D. The sum of annualised pipe cost and annual pumping energy cost
Larger pipes cost more but save energy by reducing friction. The economic size is the one with the least total annual cost; minimising pipe cost alone leads to high energy bills, and minimising friction alone leads to oversized pipes.
A proposed drip project has a present value of benefits of 420 000 and a present value of costs of 300 000. What are its benefit–cost ratio and NPV?
D. B/C = 1.40; NPV = 120 000
B/C = 420 000 / 300 000 = 1.40; NPV = 420 000 − 300 000 = 120 000. The inverse ratio gives 0.71; adding benefits and costs gives 720 000. A B/C above 1 with positive NPV indicates the project is worthwhile at the discount rate used.
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
Read the manual chapters for these first and do every worked question you can find on them.
Aim for one sitting per unit, then mixed questions across them.
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Do these early in revision so they are fast on the day.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
| Free | Smarter | |
|---|---|---|
| Grow guides, pest pages, articles | Read all | Read all |
| Ask Laisha | 5 a day | Up to 1,000 a month |
| Exam practice | The sample on each page | Every question, timed papers |
| Crop calendar and pest alerts | — | For your own fields |
| Calculators and tools | — | All |
| Uploads and reports | — | 100 a month, real files |
An AI operating system for agriculture: free guides, manuals and tools written for every country.